Agilent Technologies B2901 Manuel utilisateur

Agilent B2901/02/11/12A Precision Source/Measure Unit

How to source continuous pulses without any measurement

This material shows how to setup the instrument to source continuous pulses without any measurement using the

B2901/02/11/12A, through example to source 2 V continuous pulses with the timing parameters such as 300 us pulse

delay, 200 us pulse width and 500 us source trigger period.

Figure 1 shows the timing chart for the continuous pulse source.

Figure 1. Timing chart for the continuous pulse source

It is required to abort the instrument when you’d like to stop sourcing continuous pulses.

This material also shows how to abort the instrument to stop continuous pulses.

Setting up the pulse condition

Step 1. Press to edit the source function, and then select to set the source function to the voltage

source.

TIMER TriggerOutput ON

Source Value

Output

Off State

V or I

Time

TPD TPW

Pulse

Peak Value

TPD TPW TPD TPW

TSP TSP TSP

TPW : Pulse WidthTPD : Pulse Delay TSP : Source Trigger Period

(1) Press Mode (2) Press VOLTS (V)

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 2. Press to edit the source value, and then enter 0 V to set the source value to 0 V.

Step 3. Press to edit the limit value, and then enter 10 mA to set the limit value to 10 mA.

Step 4. Press to change the keys shown in Assist keys, and then press to show Pulse Sub-Panel.

Step 5. Press , then press to set the pulse source ON. After turning on the pulse source, you can

see Source Shape which shows the pulse source mode.

(1) Press Source (2) Enter Source Value

(1) Press Limit (2) Enter Limit Value

(1) Press Show Pulse (2) Pulse Sub-Panel appears

(1) Press ON Source Shape

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 6. Rotate to select Channel 1 Pulse Parameters and set them up as below.

(Peak: 2 V, Delay: 300 us, Width: 200 us)

Step 7. Press to show Trigger Sub-Panel.

Step 8. Press to edit the trigger type, and then select to set the trigger type to MANUAL.

(1) Press Show Trigger (2) Trigger Sub-Panel appears

(2) Press MANUAL(1) Press

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 9. Rotate to select the source trigger period and press to edit it. Then enter 500 us to set the

source trigger period to 500 us.

Step 10. Rotate to select the source trigger source and press to edit it. Then press to set

the source trigger source to TIMER.

Step 11. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 12. Press and then press to open Trigger Configuration dialogue.

(2) Enter Source Trigger Period(1) Rotate and press

Source Trigger Period

to edit

(2) Press TIMER(1) Rotate and press

Source Trigger Source

to edit

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Config

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 13. Press and select to specify the layer, the trigger parameters of which are configured.

Step 14. Rotate to select the arm count and press to edit it. Then press to set the arm

count to INFINITY.

Step 15. Press to make the modification effective.

(2) Press ARM(1) Press

(2) Press INF.

(1) Rotate and press

ARM Count

to edit

(1) Press OK to make the modification effective

Agilent B2901/02/11/12A Precision Source/Measure Unit

Starting sourcing the continuous pulses

Step 16. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 17. Press , , , and then press to start sourcing the

continuous pulses.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Initiate

(3) Press Trans.

(4) Press Ch 1

Agilent B2901/02/11/12A Precision Source/Measure Unit

Stopping sourcing the continuous pulses

Step 18. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 19. Press , , , and then press to stop sourcing the

continuous pulses.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Abort

(3) Press Trans.

(4) Press Ch 1

Autres manuels pour B2901

Ce manuel convient aux modèles suivants

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies VS Series Guide de référence

Agilent Technologies

Agilent Technologies 8753ET Manuel utilisateur

Agilent Technologies

Agilent Technologies OmniBER OTN Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies E4418B Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent 8163A Mode d'emploi

Agilent Technologies

Agilent Technologies E5072A ENA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies PNA Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies ESA-E E4407B Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 700 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies N9039A Manuel utilisateur

Agilent Technologies

Agilent Technologies 85052A Mode d'emploi

Agilent Technologies

Agilent Technologies E8363A Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 4500 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 1146B Manuel utilisateur

Agilent Technologies

Agilent Technologies ESA-E E4404B Manuel utilisateur

Agilent Technologies

Agilent Technologies 85103F Manuel utilisateur

Agilent Technologies

Agilent Technologies PSA Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies N6705 Manuel utilisateur

Agilent Technologies

Agilent Technologies U1271A Manuel utilisateur

Agilent Technologies

Agilent Technologies 4352B Manuel utilisateur

Agilent Technologies

Agilent Technologies LogicWave Manuel utilisateur

Agilent Technologies

Agilent Technologies E4402B Option H3B Manuel

Agilent Technologies

Agilent Technologies E4402/7B Manuel

Agilent Technologies

Agilent Technologies 16718A Guide de référence

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur