Agilent Technologies E4419B Manuel utilisateur

Agilent Technologies

Agilent

E4419B Power Meter

User’s Guide

ii E4419B Power Meter User’s Guide

Notices

2008-2010

No part of this manual may be reproduced

in any form or by any means (including

electronic storage and retrieval or

translation into a foreign language) without

prior agreement and written consent from

Agilent Technologies, Inc. as governed by

United States and international copyright

laws.

Manual Part Number

E4419-90006

Edition

Sixth Edition, April 23, 2010

Printed in Malaysia

Agilent Technologies, Inc.

3501 Stevens Creek Blvd.

Santa Clara, CA 95052 USA

Warranty

The material contained in this

document is provided “as is,” and is

subject to being changed, without

notice, in future editions. Further, to

the maximum extent permitted by

applicable law, Agilent disclaims all

warranties, either express or implied,

with regard to this manual and any

information contained herein,

including but not limited to the

implied warranties of

merchantability and fitness for a

particular purpose. Agilent shall not

be liable for errors or for incidental or

consequential damages in

connection with the furnishing, use,

or performance of this document or of

any information contained herein.

Should Agilent and the user have a

separate written agreement with

warranty terms covering the material

in this document that conflict with

these terms, the warranty terms in the

separate agreement shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a

license and may be used or copied only in

accordance with the terms of such

license.

Restricted Rights Legend

U.S. Government Restricted Rights.

Software and technical data rights granted

to the federal government include only

those rights customarily provided to end

user customers. Agilent provides this

customary commercial license in Software

and technical data pursuant to FAR 12.211

(Technical Data) and 12.212 (Computer

Software) and, for the Department of

Defense, DFARS 252.227-7015 (Technical

Data - Commercial Items) and DFARS

227.7202-3 (Rights in Commercial Computer

Software or Computer Software

Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in damage to the product or

loss of important data. Do not

proceed beyond a CAUTION notice

until the indicated conditions are

fully understood and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in personal injury or death.

Do not proceed beyond a

WARNING notice until the

indicated conditions are fully

understood and met.

E4419B Power Meter User’s Guide iii

Certification

Agilent Technologies certifies that this product met its published

specifications at the time of shipment from the factory. Agilent

Technologies further certifies that its calibration measurements are

traceable to the United States National Institute of Standards and

Technology, to the extent allowed by the Institute’s calibration facility and

to the calibration facilities of other International Standards Organization

members.

Warranty

This Agilent Technologies instrument product is warranted against

defects in material and workmanship for a period of one year from date of

shipment. During the warranty period, Agilent Technologies will at its

option, either repair or replace products which prove to be defective. For

warranty service or repair, this product must be returned to a service

facility designated by Agilent Technologies. Buyer shall prepay shipping

charges to Agilent Technologies and Agilent Technologies shall pay

shipping charges, duties and taxes for products returned to Agilent

Technologies from another country. Agilent Technologies warrants that its

software and firmware designated by Agilent Technologies for use with

an instrument will execute its programming instructions when properly

installed on that instrument. Agilent Technologies does not warrant that

the operation of the instrument, or firmware will be uninterrupted or error

free.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper

or inadequate maintenance by Buyer, Buyer-supplied software or

interfacing, unauthorized modification or misuse, operation outside of the

environmental specifications for the product, or improper site preparation

or maintenance. NO OTHER WARRANTY IS EXPRESSED OR IMPLIED.

AGILENT TECHNOLOGIES SPECIFICALLY DISCLAIMS THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

iv E4419B Power Meter User’s Guide

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER’S SOLE AND EXCLUSIVE

REMEDIES. AGILENT TECHNOLOGIES SHALL NOT BE LIABLE FOR ANY

DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER

LEGAL THEORY.

Warnings and Cautions

This guide uses warnings and cautions to denote hazards.

Recommended Calibration Interval

Agilent Technologies recommends a two- years calibration cycle for the

E4419B power meter.

WARNING A warning calls attention to a procedure, practice or the like, which, if

not correctly performed or adhered to, could result in injury or the loss of

life. Do not proceed beyond a warning until the indicated conditions are

fully understood and met.

CAUTION A caution calls attention to a procedure, practice or the like which, if not

correctly performed or adhered to, could result in damage to or the

destruction of part or all of the equipment. Do not proceed beyond a

caution until the indicated conditions are fully understood and met.

E4419B Power Meter User’s Guide v

Safety Symbols

The following symbol on the instrument and in the documentation

indicates precautions that must be taken to maintain safe operation of

the instrument.

Caution, risk of danger.

The Instruction Documentation Symbol. The product is marked with this

symbol when it is necessary for the user to refer to the instructions in the

supplied documentation.

Alternating current (AC).

This symbol indicates the operating switch for ‘Stand-by’ mode. Note, the

instrument is NOT isolated from the mains when the switch is pressed.

To isolate the instrument, the mains coupler (mains input cord) should be

removed from the power supply.

This symbol indicates the operating switch for ‘On’ mode).

External Protective Earth Terminal.

While this is a Class I product, provided with a protective earthing

conductor in a power cord, an external protective earthing terminal has

also been provided. This terminal is for use where the earthing cannot be

assured. At least an 18AWG earthing conductor should be used in such

an instance, to ground the instrument to an assured earth terminal.

vi E4419B Power Meter User’s Guide

Personal Safety Considerations

This is a Safety Class I product (provided with a protective earthing

ground incorporated in the power cord). The mains plug shall only be

inserted in a socket outlet provided with a protective earth contact. Any

interruption of the protective conductor, inside or outside the instrument,

is likely to make the instrument dangerous. Intentional interruption is

prohibited

General Safety Considerations

WARNING If this instrument is not used as specified, the protection provided by the

equipment could be impaired. This instrument must be used in a normal

condition (in which all means of protection are intact) only.

No operator serviceable parts inside. Refer servicing to qualified

personnel. To prevent electrical shock, do not remove covers.

For continued protection against fire hazard, replace the line fuse(s)

only with fuses of the same type and rating (for example, normal blow,

time delay, etc.). The use of other fuses or material is prohibited.

WARNING Before this instrument is switched on, make sure it has been properly

grounded through the protective conductor of the ac power cable to a

socket outlet provided with protective earth contact.

Any interruption of the protective (grounding) conductor, inside or

outside the instrument, or disconnection of the protective earth terminal

can result in personal injury.

CAUTION Any adjustments or service procedures that require operation of the

instrument with protective covers removed should be performed only by

trained service personnel.

E4419B Power Meter User’s Guide vii

Regulatory Markings

The CE mark shows that the product complies with all the relevant

European legal Directives (if accompanied by a year, it signifies when the

design was proven.

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme à la norme NMB-001 du Canada.

This is the symbol of an Industrial Scientific and Medical Group 1 Class A

product.

The CSA mark is a registered trademark of the Canadian Standards

Association.

viii E4419B Power Meter User’s Guide

IEC 1010-1 Compliance

This instrument has been designed and tested in accordance with IEC

Publication 61010-1 +A1:1992 Safety Requirements for Electrical

Equipment for Measurement, Control and Laboratory Use and has been

supplied in a safe condition. The instruction documentation contains

information and warnings which must be followed by the user to ensure

safe operation and to maintain the instrument in a safe condition.

Statement of Compliance

This product has been designed and tested for compliance with IEC 60529

(1989) Degrees of Protection Provided by Enclosures (IP Code). Level IPx4

is attained if, and only if, the carry case( Agilent Technologies part number

34141A) is fitted.

User Environment

This product is designed for use in a sheltered environment (avoiding

extreme weather conditions) in accordance with Pollution Degree 3

defined in IEC 60664-1, with the carry case (Agilent Technologies part

number 34141A) fitted over the instrument.

The product is suitable for indoor use only, when this carry case is not

fitted.

Installation Instructions

To avoid unnecessary over-temperature conditions, while this carry case

is fitted do not apply an ac mains supply voltage, only operate your

Agilent Technologies E4419B from the battery pack.

E4419B Power Meter User’s Guide ix

Regulatory Information

Sound Emission

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der

Maschinenlarminformationsverordnung vom 18 Januar 1991.

• Sound Pressure LpA < 70 dB.

• Am Arbeitsplatz.

• Normaler Betrieb.

• Nach DIN 45635 T. 19 (Typprufung).

Manufacturers Declaration

This statement is provided to comply with the requirements of the

German Sound DIN 45635 T. 19 (Typprufung).

• Sound Pressure LpA < 70 dB.

• At operator position.

• Normal operation.

• According to ISO 7779 (Type Test).

Australian EMC Regulations

The C-Tick mark is a registered trademark of the Spectrum Management

Agency of Australia. This signifies compliance with the Australian EMC

Framework Regulations under the terms of the Radiocommunications Act

of 1992.

N279

x E4419B Power Meter User’s Guide

Declaration of Conformity (DoC)

The Declaration of Conformity (DoC) for this instrument is available on the

Web site. You can search the DoC by its product model or description.

http://regulations.corporate.agilent.com/DoC/search.htm

NOTE If you are unable to search for the respective DoC, please contact your

local Agilent representative.

Autres manuels pour E4419B

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies E5061B Manuel utilisateur

Agilent Technologies

Agilent Technologies 8510C Manuel utilisateur

Agilent Technologies

Agilent Technologies 4288A Manuel du propriétaire

Agilent Technologies

Agilent Technologies FieldFox N9912A Manuel utilisateur

Agilent Technologies

Agilent Technologies ESA-E Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies PNA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies N5502A Manuel utilisateur

Agilent Technologies

Agilent Technologies U1731C Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent 7890 Series Mode d’emploi

Agilent Technologies

Agilent Technologies 1146B Manuel utilisateur

Agilent Technologies

Agilent Technologies X Series Manuel utilisateur

Agilent Technologies

Agilent Technologies U3051C Manuel du propriétaire

Agilent Technologies

Agilent Technologies 8504B Manuel utilisateur

Agilent Technologies

Agilent Technologies PNA Series Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 89604 Manuel utilisateur

Agilent Technologies

Agilent Technologies 4418B Manuel utilisateur

Agilent Technologies

Agilent Technologies 8510XF Manuel de service

Agilent Technologies

Agilent Technologies u8903a Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent 4396B Manuel utilisateur

Agilent Technologies

Agilent Technologies 42841A Manuel utilisateur

Agilent Technologies

Agilent Technologies 1145A Manuel

Agilent Technologies

Agilent Technologies E5900B Manuel utilisateur

Agilent Technologies

Agilent Technologies 42941A Manuel d'utilisation

Agilent Technologies

Agilent Technologies ESA-E E4402B Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur