AEMC instruments SR759 Manuel utilisateur

AC Current Probe

Model SR759

User Manual

DESCRIPTION

The SR759 (Catalog #2116.33) is designed for use in industrial environments. The ergonomic design allows

itm to easily attach to cables or small bus bars. The “circular” jaws guarantee a very good accuracy and low

phase shift. The probe has four measurement ranges with the highest range measuring to 1000Arms

continuous and is compatible with any AC Voltmeter, multimeter, or other voltage measurement instrument

that has the following features: Range and resolution capable of displaying 1mV of output per amp of

measured current; Voltmeter accuracy of 0.75% or better to take full advantage of the accuracy of the

probe; Input impedance of ≥10MΩ.

WARNING

The safety warnings are provided to ensure the safety of personnel and proper operation of the

instrument. Read the instruction completely.

• Use caution on any circuit: potentially high voltages and currents may be present and may pose a

shock hazard.

• Do not use the probe if damaged. Always connect the current probe to the measuring device before it

is connected around the conductor

• Do not use on non-insulated conductor with a potential to ground greater than 600V CAT III pollution

2. Use extreme caution when clamping around bare conductors or bus bars.

• Before each use, inspect the probe; look for cracks in housing or output cable insulation.

• Do not use clamp in wet environment or in locations that hazardous gases exist.

• Do not use the probe anywhere beyond the tactile barrier.

INTERNATIONAL ELECTRICAL SYMBOLS

This symbol signifies that the current probe is protected by double or reinforced insulation. Use only

factory specified replacement parts when servicing the instrument.

This symbol signifies CAUTION! and requests that the user refer to the user manual before using

the instrument.

This is a type A current sensor. This symbol signifies that application around and removal from

HAZARDOUS LIVE conductors is permitted.

DEFINITION OF MEASUREMENT CATEGORIES

CAT IV: For measurements performed at the primary electrical supply (<1000V) such as on primary

overcurrent protection devices, ripple control units, or meters.

CAT III: For measurements performed in the building installation at the distribution level such as on

hardwired equipment in fixed installation and circuit breakers.

CAT II: For measurements performed on circuits directly connected to the electrical distribution system.

Examples are measurements on household appliances or portable tools.

RECEIVING YOUR SHIPMENT

Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify your

distributor of any missing items. If the equipment appears to be damaged, file a claim immediately with the

carrier and notify your distributor at once, giving a detailed description of any damage.

ELECTRICAL SPECIFICATIONS

Current Range:

1mA to 1.2A, 0.01 to 12A, 0.1 to 120A, 1 to 1200A

Output Signal: 1000mV/AAC (1V @ 1A),

100mV/AAC (1V @ 10A), 10mV/AAC (1V @

100A), 1 mV/AAC (1V @ 1000A)

Accuracy and Phase Shift*:

1A Range

Primary Current

Accuracy %

Phase Shift

0.001 to 0.01A

3% + 1mV

Not Specified

0.01 to 0.1A

≤3% + 1mV

Not Specified

0.1 to 1A

≤0.7% + 1mV

≤10°

1 to 1.2A

≤0.7% + 1mV

≤10°

10A Range

Primary Current

Accuracy %

Phase Shift

0.01 to 0.1A

1% + 0.2mV

Not Specified

0.1 to 1A

≤0.5% + 0.2mV

≤5°

1 to 10A

≤0.5%

≤2°

10 to 12A

≤0.5%

≤2°

100A Range

Primary Current

Accuracy %

Phase Shift

0.1 to 1A

1% + 0.2mV

Not Specified

1 to 10A

≤0.5% + 0.2mV

≤2°

10 to 100A

≤0.3%

≤1°

100 to 120A

≤0.2%

≤1°

1000 A Range

Primary Current

Accuracy %

Phase Shift

1 to 10A

1% + 0.2mV

Not Specified

10 to 100A

≤ 0.5% + 0.2mV

≤ 2°

100 to 1000A

≤ 0.2%

≤ 1°

1000 to 1200A

≤ 0.2%

≤ 1°

*Reference conditions: 23°C ± 3°K, 20 to 75% RH, 48

to 65Hz, external magnetic field < 40A/m, no DC

component, no external current carrying conductor, test

sample centered. Load impedance 10MΩ

Overload: 1200A for 15 min on, 30 min off

Accuracy: Per IEC 185

Frequency Range: 30Hz to 3kHz; current

derating above 500Hz using the formula:

×



()

Load Impedance: 100kΩmin

Working Voltage: 600V CAT III

Common Mode Voltage: 600V CAT III

Influence of Adjacent Conductor: < 1mA/AAC

Influence of Conductor in Jaw Opening:

0.3% of Reading

Influence of Frequency:

1mV/A Range: < 1% R from 10Hz to 1kHz

10mV/A Range: < 1.5% R from 10Hz to 3kHz

100mV/A Range: < 2% R from 10Hz to 3kHz

1000mV/A Range: < 2% R from 30Hz to 1kHz

Open Voltage: 8V peak max.

MECHANICAL SPECIFICATIONS

Operating Temperature:

14° to 122°F (-10° to 50°C)

Storage Temperature:

-4° to 158°F (-20° to 70°C)

Influence of Temperature:

< 0.15% per 10°K

Influence of Humidity:

From 10 to 90%: 0.1%

Jaw Opening: 2.25" (57mm) max

Maximum Conductor Size:

2.05" (52mm)

Envelope Protection: IP 40 (IEC 529)

Drop Test: 1 m (IEC 68-2-32)

100 g (IEC 68-2-27)

Vibration:

5 to 15Hz, 0.15mm (IEC 68-2-6)

Material:

Handles and jaws: Polycarbonate UL94V0

Dimensions:

4.37 x 8.50 x 1.77" (111 x 216 x 45mm)

Weight:

1.21 lbs (550g)

Output:

Two-core cord with reinforced or double insulation,

1.5m (5ft) terminated with 2 safety plugs (4mm)

SAFETY SPECIFICATIONS

Electrical Conformity to International Standards:

This instrument is compliant with IEC 61010-2-032,

300V category IV and 600V category III.

Double or reinforced insulation .

Type of current sensor per IEC 61010-2-032:

type A .

Electromagnetic Compatibility:

The device is in conformity with standard IEC

61326-1.

ORDERING INFORMATION

AC Current Probe SR759 ................ Cat #2116.33

Accessories:

Adapter - Banana (Female) – BNC

(Male) (XM-BB) (600V CAT III) ........ Cat #2118.46

Banana plug adapter

(to non-recessed plug) ...................... Cat #1017.45

25 to 55Hz, 0.25mm

15 to 25Hz, 1mm

99-MAN 100168 v13 08/21

OPERATION

Please make sure that you have already read and fully understand the WARNING section on page 1.

Making Measurements with the AC Current Probe Model SR759

•Connect the black and red terminals to the 2VAC range of your DMM or voltage measuring instrument.

Select the appropriate current range (1000/1V). Clamp the probe around the conductor to be tested with

the arrow pointed toward the load. Read the value display on the DMM and multiply it by the probe ratio

selected. (e.g. If reading = 185mV, the current flowing through the probe is 185 x 1000 = 185,000mA =

185A when 1mV/A range is selected.)

•For best accuracy, avoid if possible, the proximity of other conductors which may create noise.

Tips for Making Precise Measurements

•When using a current probe with a meter, it is important to select the range that provides the best

resolution. Failure to do this may result in measurement errors.

•Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air

gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for

power measurement.

MAINTENANCE

Warning:

•For maintenance use only original replacement parts.

•To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.

•To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents

into the probe.

Cleaning: To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all

times. Failure to do so may result in error in readings. To clean the probe jaws, use very fine sand paper (fine

600) to avoid scratching the jaw then gently clean with a soft oiled cloth.

REPAIR AND CALIBRATION

You must contact our Service Center for a Customer Service Authorization number (CSA#). This will ensure

that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA# on the

outside of the shipping container.

Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments

15 Faraday Drive • Dover, NH 03820 USA

(800) 945-2362 x360 • (603) 749-6434 x360 • repair@aemc.com

(Or contact your authorized distributor)

NOTE: All customers must obtain a CSA# before returning any instrument.

TECHNICAL AND SALES ASSISTANCE

If you are experiencing any technical problems, or require any assistance with the proper use or application

of this instrument, please contact our technical hotline:

(800) 945-2362 (Ext. 351) • (603) 749-6434 (Ext. 351) • techsupport@aemc.com

LIMITED WARRANTY

The current probe is warranted to the owner for a period of two years from the date of original purchase

against defects in manufacture. This limited warranty is given by AEMC®Instruments, not by the distributor

from whom it was purchased. This warranty is void if the unit has been tampered with, abused or if the defect

is related to service not performed by AEMC®Instruments.

Full warranty coverage and product registration is available on our website at: www.aemc.com/warranty.html

Please print the online Warranty Coverage Information for your records.

Autres manuels AEMC instruments Instrument de mesure

AEMC instruments

AEMC instruments JM840A Manuel utilisateur

AEMC instruments

AEMC instruments 6505 Manuel utilisateur

AEMC instruments

AEMC instruments MN213 Manuel utilisateur

AEMC instruments

AEMC instruments 1035 Manuel utilisateur

AEMC instruments

AEMC instruments PEL 105 Manuel utilisateur

AEMC instruments

AEMC instruments SR701 Manuel utilisateur

AEMC instruments

AEMC instruments 407 Manuel utilisateur

AEMC instruments

AEMC instruments MN185 Manuel utilisateur

AEMC instruments

AEMC instruments 502 Manuel utilisateur

AEMC instruments

AEMC instruments 403 Manuel utilisateur

AEMC instruments

AEMC instruments 1510 Manuel utilisateur

AEMC instruments

AEMC instruments AmpFlex 193-24-BK Manuel utilisateur

AEMC instruments

AEMC instruments K100 Manuel utilisateur

AEMC instruments

AEMC instruments MD303 Manuel utilisateur

AEMC instruments

AEMC instruments MA194-24-BK Manuel utilisateur

AEMC instruments

AEMC instruments MR6292 Manuel utilisateur

AEMC instruments

AEMC instruments CM605 Manuel utilisateur

AEMC instruments

AEMC instruments OX5042 Manuel utilisateur

AEMC instruments

AEMC instruments CA846 Manuel utilisateur

AEMC instruments

AEMC instruments 6505 Manuel utilisateur

AEMC instruments

AEMC instruments MN125 Manuel utilisateur

AEMC instruments

AEMC instruments MN103 Manuel utilisateur

AEMC instruments

AEMC instruments PowerPad IV 8345 Manuel utilisateur

AEMC instruments

AEMC instruments A196-24-BK Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur