AEMC instruments OX5042 Manuel utilisateur

Model OX5042 Handscope

Instructions for General Electrical

Measurements

First-Time Setup

1. Turn the instrument ON.

2. Press Scope Mode .

3. Press Channel A . The main menu appears as follows at the bottom of the

screen (default settings):

4. Press Channel B .

5. Press the right navigation key until the Multiplier field is highlighted. By

default this is set to x1.

6. Press the down navigation key until the x1000 setting is highlighted.

7. Press Enter to save the setting.

8. Press to highlight the Units field.

9. Press to highlight the Asetting.

10. Press to save the setting. The main menu now appears as follows:

NOTE: These settings will remain in effect (even if the instrument batteries are

drained or removed) until changed by the user.

11. Apply the voltage to be measured to Channel A and current to Channel B.

12. Press the Auto Set button to properly scale the measurements.

www.calcert.com [email protected]1.800.544.2843 0

AC Voltage Measurement

1. Attach the BNC adapter (shown on right) to the Channel A input.

2. Attach the 10’ black and red leads to the adapter.

3. Select the alligator or pencil tip probes and attach them to the

leads as needed.

4. Attach the test leads to the measurement point.

5. Turn the instrument ON.

6. Press Scope Mode .

7. Press Channel A . Verify that the main menu appears as follows:

8. Press Meter Mode . The voltage measurement appears on the screen

(see the example below):

9. Press Aand verify that Auto is ON in the menu at the bottom of the

display. If it isn’t, use the right navigation key to highlight Auto then the up or

down navigation key to select ON.

10. The bottom display should appear as follows:

NOTE: If this menu screen is not displayed, press the Meas key.

Then, press the Achannel key to show the menu.

11. Read the voltage and record it: ___________________________

www.calcert.com [email protected]1.800.544.2843 0

AC Current Measurement

1. Select the current probe based on the current to be measured:

•MN251T (if in your kit) for measuring from 1 – 200A

•MN379T (if in your kit) for measuring from 0.05 – 120A

•MiniFlex sensor for measuring 10 – 3000A.

2. Attach the current probe to the Channel B input.

3. Clip the current probe around the conductor to be measured.

4. Turn the instrument ON.

5. Press Scope Mode .

6. Press Channel B . Verify the main menu appears as follows:

7. Press Meter Mode . The current measurement appears on the Channel B

display (see the example below):

8. Press Band verify that Auto is ON in the menu at the bottom of the display.

If it isn’t, use the right navigation key to highlight Auto then the up or down

navigation key to select ON.

9. The bottom display appear as follows:

NOTE: If this menu screen is not displayed, press the Meas key. Then,

press the Bchannel key to show the menu.

10. Read the current and record it: ___________________________

www.calcert.com [email protected]1.800.544.2843 0

AC Current Harmonics

1. Set up the instrument for current measurement, as instructed by steps 1

through 6 of the “AC Current Measurement” section above.

2. Press Harmonics Mode . The THD (Total Harmonics Distortion) percentage

appears in the upper right corner on the Channel B display (see the example

below):

3. Record the THD percentage: ________________ %

NOTE: If either channel is not connected, an error message appears. To eliminate

the error and clear the message, rapidly press twice the key for the channel

causing the error. This turns OFF the channel, removes the error message, and

displays the THD of the active channel. The channel that is OFF is grayed out. To

re-activate the channel, press its button.

www.calcert.com [email protected]1.800.544.2843 0

Millivolt Drop

1. Set up the instrument for voltage measurement, as instructed by steps 1

through 6 of the “AC Voltage Measurement” section on page 2 above.

2. Press Channel A .

3. Move the test leads to each measurement point, and record each millivolt drop:

___________ ___________ ___________

If applicable, record the completed measurements in your report software.

www.calcert.com [email protected]1.800.544.2843 0

Table des matières

Autres manuels AEMC instruments Instrument de mesure

AEMC instruments

AEMC instruments 6528 Manuel utilisateur

AEMC instruments

AEMC instruments A196-24-BK Manuel utilisateur

AEMC instruments

AEMC instruments 1015 Manuel utilisateur

AEMC instruments

AEMC instruments DIGITAL FLEXPROBE 400D-6 Manuel utilisateur

AEMC instruments

AEMC instruments Measure Up PowerPad III Manuel utilisateur

AEMC instruments

AEMC instruments 6536 Manuel utilisateur

AEMC instruments

AEMC instruments 6536 Manuel utilisateur

AEMC instruments

AEMC instruments 6505 Manuel utilisateur

AEMC instruments

AEMC instruments MR525 Manuel utilisateur

AEMC instruments

AEMC instruments MR6292 Manuel utilisateur

AEMC instruments

AEMC instruments JM852 Manuel utilisateur

AEMC instruments

AEMC instruments 6292 Manuel utilisateur

AEMC instruments

AEMC instruments MN134 Manuel utilisateur

AEMC instruments

AEMC instruments MD304 Manuel utilisateur

AEMC instruments

AEMC instruments MN185 Manuel utilisateur

AEMC instruments

AEMC instruments 6527 Manuel utilisateur

AEMC instruments

AEMC instruments Chauvin Arnoux 6412 Manuel utilisateur

AEMC instruments

AEMC instruments SIMPLE LOGGER L100 Manuel utilisateur

AEMC instruments

AEMC instruments K100 Manuel utilisateur

AEMC instruments

AEMC instruments 6550 Manuel utilisateur

AEMC instruments

AEMC instruments MN185 Manuel utilisateur

AEMC instruments

AEMC instruments PowerPad IV 8345 Manuel utilisateur

AEMC instruments

AEMC instruments JM835A Manuel utilisateur

AEMC instruments

AEMC instruments 5070 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur