Advantech EKI-6340 Series Manuel utilisateur

PCI-RF module

DNMA-92 User Manual

Version: 1.0

April 2009

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, whether electronic, mechanical,

photocopying, recording or otherwise without the prior writing of the publisher.

Windows™98SE/2000/ME/XP are trademarks of Microsoft®Corp.

Pentium is trademark of Intel.

All copyright reserved.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the

following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with

any other antenna or transmitter.

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted

in indoor environment only.

Devices will not permit operations on channels 120-132 for 11a and 11n/a which

overlap the 5600 - 5650 MHz band.

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible

for the FCC compliance requirement of the end product, which integrates this module.

20cm minimum distance has to be able to be maintained between the antenna and the

users for the host this module is integrated into. Under such configuration, the FCC

radiation exposure limits set forth for an population/uncontrolled environment can be

satisfied.

Any changes or modifications not expressly approved by the manufacturer could void

the user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at

least 20cm separation with the antenna while this end product is installed and

operated. The end user has to be informed that the FCC radio-frequency exposure

guidelines for an uncontrolled environment can be satisfied. The end user has to also

be informed that any changes or modifications not expressly approved by the

manufacturer could void the user's authority to operate this equipment. If the size of

the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is

required to be available in the users manual: This device complies with Part 15 of

FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference and (2) this device must accept any interference

received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains

TX FCC ID: M82-EKI6430 ". If the size of the end product is larger than 8x10cm,

then the following FCC part 15.19 statement has to also be available on the label:

This device complies with Part 15 of FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

Approved antenna for the End product.

Theaboveapprovedantennaisonlyallowedtouseforthemodule.Itwillbe

necessarytokeep20cmawayfromhumanbody.Otherantennatypeorsame

antennatypebuthigherantennagainisnotallowedtouse.

IMPORTANT NOTE: In the event that these conditions can not be met (for example

used within 20cm or higher antenna gain), then the FCC authorization is no longer

considered valid and the FCC ID can not be used on the final product. In these

circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC authorization.

Table of Contents

1. INTRODUCTION 6

2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 7

2.1 INSTALLATION .........................................................................................................7

2.2 ADDITIONAL SETUP PROCESSES............................................................................10

2.3 UNINSTALLATION...................................................................................................11

3. CONNECTING TO AN EXISTING NETWORK 12

4. CREATINGAN AD HOC NEW NETWORK 17

5. MODIFYINGAWIRELESS NETWORK 21

5.1 INFRASTRUCTURE MODE AND AD HOC MODE.....................................................21

5.2 MODIFYINGAWIRELESS NETWORK.....................................................................22

5.3 DEFAULT SETTINGS WINDOWS XP ZERO-CONFIGURATION................................29

5.4 SUPER A/G SETTING.......................................................... 29。

APPENDIX A: FAQ ABOUT WLAN 30

APPENDIX B: SPECIFICATION 32

1. Introduction

Thank you for purchasing the WLAN a/b/g/n mini-PCI Module that provides the

easiest way to wireless networking. This User Manual contains detailed instructions in

the operation of this product. Please keep this manual for future reference.

System Requirements

 A laptop PC contains:

- 32 MB memory or greater

- 300 MHz processor or higher

 Microsoft®Win™2000/ME/98 Second Edition/XP

2. Driver/Utility Installation / Uninstallation

2.1 Installation

Note! The Installation Section in this User Manual describes the first-time installation

for Windows. To re-install the driver, please first uninstall the previously

installed driver. See Chapter 2.3 “Uninstallation” in this User Manual.

Follow the steps below to complete the driver/utility installation:

1. Insert the Installation Software CD into the CD-Rom Drive.

2. Click “Next”.

3. Read the License Agreement and click “Yes”.

4. Click “Next” to continue or click “Browse” to choose a destination folder.

5. Click “Next”.

6. Click “Yes” to create a shortcut icon on your desktop.

7. Click “Finish”.

8. You should now see a shortcut icon on your desktop.

Autres manuels pour EKI-6340 Series

Table des matières

Autres manuels Advantech Carte PCI

Advantech

Advantech MIC-3401 Manuel utilisateur

Advantech

Advantech PCI-1736UP Manuel utilisateur

Advantech

Advantech MIC-3620 Manuel utilisateur

Advantech

Advantech PCI-1733 Manuel d'installation et d'exploitation

Advantech

Advantech PCI-1758 Series Manuel utilisateur

Advantech

Advantech PCI-1710U Manuel utilisateur

Advantech

Advantech PCI-1625U Manuel utilisateur

Advantech

Advantech UNO-P166 Manuel d'installation et d'exploitation

Advantech

Advantech PCI-1757UP Manuel utilisateur

Advantech

Advantech ARK-5261 Manuel d'installation et d'exploitation

Advantech

Advantech PCIE-1758 Series Manuel utilisateur

Advantech

Advantech MIC-3756 Manuel utilisateur

Advantech

Advantech PCA-5630 Manuel d'installation et d'exploitation

Advantech

Advantech PCIE-1805 Manuel utilisateur

Advantech

Advantech MIC-3640 Manuel utilisateur

Advantech

Advantech PCI-1220U Manuel utilisateur

Advantech

Advantech PCI-1750 Manuel utilisateur

Advantech

Advantech PCI-1780 Manuel utilisateur

Advantech

Advantech MIC-3756 Manuel utilisateur

Advantech

Advantech PCI-1601 Manuel utilisateur

Advantech

Advantech PCM-2312 Manuel utilisateur

Advantech

Advantech PCIE-1802 Manuel utilisateur

Advantech

Advantech PCM-3641I Manuel d'installation et d'exploitation

Advantech

Advantech PCI-1723 Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur