Advantech IPMI-1000 Manuel d'installation et d'exploitation

IPMI-1000 Startup Manual 1

Before you begin installing your card, please make sure that

the following items have been shipped:

1. IPMI-1000 module x 1

2. Startup manual x 1 PN: 20061IPM100

3. Screw x 2 P/N: 19350304A0

4. Warranty Card x 1 P/N: 2190000902

5. VGA cable x 1 P/N: 1700020805

If any of these items are missing or damaged, please con-

tact your distributor or sales representative immediately.

IPMI-1000

IPMI module, AST2300 chipset

Startup Manual

General Features

• Out of band (OS independent)

• User management

• Remote control

• System health

• Maintenance

SBC Support List

PPCE-7127G2-00A1E

PCE-5126WG2-00A1E

Note: For more SBC support list, please visit our website.

Mechanical and Environmental

• Dimensions: 68 mm x 31.5 mm

• Power supply type: 5 VSB

• Power requirements: 5 VSB @ 55mA

• Operating temperature: 0 ~ 60° C

• Operating humidity: 60° C @ 85% RH, Non-Condensing

• Storage temperature: -40 ~ 85° C

• Storage humidity: 60° C @ 95% RH, Non-Condensing

• Weight: 0.48 kg

There are four connectors on the module and one of them

is used to connect with SBC. The below table lists the func-

tions of these connectors.

Connectors

Label Function

BMC1 IPMI connector

VGA1 VGA1 connector

MRCROSD1 Local media device

IPMB Reserved

Specications

Packing List

For more information on this and other Advantech

products, please visit our website at:

http://www.advantech.com

http://www.advantech.com/eplatform

For technical support and service, please visit our

support website at:

http://support.advantech.com

This manual is for the IPMI-1000 Series.

Part No. 2006IPM100

Print in China

1st Edition

October 2012

Connectors

2 IPMI-1000 Startup Manual

1. Please connect IPMI module to the SBC BMC1

connector using the following steps.

1). Connector BMC1 and the screw holes on your SBC.

If your SBC is either PCE-7127 or PCE-5126WG2,

you will ﬁnd two screw holes around BMC1.

Figure1: Locations of BMC1 & Screw holes on SBC

2). Connector BMC1 and standoffs on IPMI-1000.

Figure 2: Locations of BMC1 & standoffs on module

3). Connect the SBC and IPMI-1000 with BMC1

connector.

Figure 3: Assembling module

4). Align the screw holes, and ﬁx securely with the

screws.

Figure 4: Fixing the screws

2. After setting up the hardware conﬁguration, users

should also complete BIOS settings. Please check the

information below to ﬁnd out corresponding instructions

to enable the IPMI function.

Enter Server Mgmt, “BMC Support” and “Wait for BMC”

are [Enabled] as default setting.

Figure 5: BMC support setting

Enter BMC network conﬁguration, the default

Conﬁguration Address source is [Unspeciﬁed]. Change

Address source to [Static], there is a default IP address

for user setting in the ﬁrst time.

Figure 6: BMC network conguration setting

Note: At ﬁrst time initialing IPMI-1000, it may take around

30~40 seconds before posting BIOS. When F/W is ready,

the LED light of module will be ﬂashing.

Installation Guide

IPMI-1000 Startup Manual 3

Figure 7: IPMI-1000 Top side Board Layout

Figure 8: IPMI-1000 Bottom side Board Layout

Board Layout and Dimension

Autres manuels pour IPMI-1000

Autres manuels Advantech Unité de contrôle

Advantech

Advantech SOM-6898 Manuel utilisateur

Advantech

Advantech WISE-1510 Manuel utilisateur

Advantech

Advantech MOS-2110Z-1201E Manuel utilisateur

Advantech

Advantech PCM-3345 Manuel utilisateur

Advantech

Advantech MIO-6250 MIO/160 Manuel d'installation et d'exploitation

Advantech

Advantech Adam 4000 Series Manuel utilisateur

Advantech

Advantech WISE-4671 Manuel d'installation et d'exploitation

Advantech

Advantech PCM-24BXWF Manuel d'installation et d'exploitation

Advantech

Advantech ADAM-2000 Series Manuel utilisateur

Advantech

Advantech AMAX-4800 Series Manuel utilisateur

Advantech

Advantech USB-5801 Manuel d'installation et d'exploitation

Advantech

Advantech AIW-357 DK-G1P Manuel utilisateur

Advantech

Advantech ADAM-2510Z Manuel utilisateur

Advantech

Advantech SOM 144 Mode d’emploi

Advantech

Advantech PCM-233A Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3718 Series Manuel utilisateur

Advantech

Advantech MOS-2120-Z1101E Manuel utilisateur

Advantech

Advantech B+B SmartWorx IE-iMcV-2xLIM Manuel utilisateur

Advantech

Advantech RISC Module SOM-A2552 Manuel utilisateur

Advantech

Advantech APAX-5202P Manuel utilisateur

Advantech

Advantech B+B SmartWorx iMcV-Giga-MediaLinX TX/SFP Manuel utilisateur

Advantech

Advantech ADAM-3750 3-Wire Series Manuel d'installation et d'exploitation

Advantech

Advantech PCM-3524 Manuel utilisateur

Advantech

Advantech B+B SmartWorx iMcV-LIM Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur