ADTRAN BVL3ADJD Manuel utilisateur
jobAid
DESCRIPTION
The Small Form-Factor Pluggable (SFP) Gigabit Ethernet, Single-
Fiber is a bidirectional SFP that installs into the Optical Loop
Termination (OLT) designed to accept SFPs. The SFP provides a
single optical interface to the GigE physical interface. Installed
into an appropriate OLT, the SFP provides a Gigabit Ethernet
interface to the supporting system.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
NOTICE
In a deployment consisting of an OLT with a 1442110G1 SFP
installed; the Optical Network Unit (ONU) should have a comple-
mentary 1442110G2 SFP installed.
FEATURES
The following features are supported on the SFP:
1000Base-LX 1490 nm Transmitter
1000Base-LX 1310 nm Receiver
Optical distance: 10 km maximum
CAUTION
!
Due to compliance certification requirements, only XFPs supplied
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other XFPs.
OLT
1442110G1 1442110G2
ONU
Rx: 1310 nm
Tx: 1490 nm
Rx: 1490 nm
Tx: 1310 nm
Small Form-Factor Pluggable
1490 nm TX/ 1310 nm RX, 10km
INSTALLATION
Before installation, inspect the SFP. If damage has occurred
during shipping, file a claim with the carrier, and then contact
ADTRAN Customer Support. For more information, refer to
“Warranty”.
Installation Guidelines
The following are guidelines for this installation.
The latch on the SFP is for removal only. When removing the
SFP, rotate the latch away from the SFP. The SFP should slide
easily out of the cage.
It is recommended that the connector plug remain on
whenever the transceiver optical fiber connector is not
inserted.
Installation Steps
To install the SFP, complete the following steps:
1. Insert the SFP into the SFP cage on the circuit board of the
host module with the latch handle facing outward. Slide the
SFP all the way into the cage.
2. Exert adequate pressure to ensure the SFP is completely
seated in the SFP cage.
3. Do not remove the connector plug until the optical fiber
connection is made.
4. Continue the installation and turn-up of the host module.
SPECIFICATIONS
Optical Specifications:
oTransmit wavelength: 1490 nm
oReceive wavelength: 1310 nm
oOptical transmit level: –9 dBm to –3 dBm
oOptical receive level: –19.5 dBm to –3 dBm
oOptical distance: 10 km
oOptical connectors: LC
Extended Environmental Support:
oOperational temperature range: –40°C to +85°C
oStorage temperature range: –40°C to +85°C
oRelative humidity to 95%, noncondensing
CLEI: BVL3ADJD_ _
Product P/N: 1442110G1
Issue Date: June 2014
Document P/N: 61442110G1-22B
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following documents provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix and Engineering Guide
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2014 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442110G1-22B*
SAFETY AND REGULATORY COMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment
CAUTION
!
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
Per GR-1089-CORE the ADTRAN system that this product is
being deployed in is designed and intended for installation as
part of a Common Bonding Network (CBN). The ADTRAN
system that this product is being deployed in is not designed
nor intended for installation as part of an Isolated Bonding
Network (IBN).
Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) installation. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
The ADTRAN system chassis frame ground terminal must be
connected to a reliable earth ground to ensure that the metal
enclosure of this product is properly grounded via the
backplane connector.
NOTE
The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
This product is designed to be deployed in GR-3108-CORE
environmental Class 1, 2, & 3.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
ETSI EN 300 019-1-1 Classification of environmental conditions;
Storage, Class 1.2
ETSI EN 300 019-1-2 Classification of environmental conditions;
Transportation, Class 2.3
ETSI EN 300 019-1-3 Classification of environmental conditions;
Stationary use at weather-protected locations, Class 3.3
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3.
This product meets EU RoHS Directive 2002/95/EC and/or
applicable exemptions. Refer to www.adtran.com for further
information on RoHS/WEEE.
Ce manuel convient aux modèles suivants
1
Autres manuels ADTRAN Matériel réseau
ADTRAN
ADTRAN NetVanta Serial Dial Backup Interface Module (DIM)... Manuel utilisateur
ADTRAN
ADTRAN Express 3000 Manuel utilisateur
ADTRAN
ADTRAN 1442120G1 Manuel utilisateur
ADTRAN
ADTRAN HDSL4 Manuel utilisateur
ADTRAN
ADTRAN Total Access 850 Mode d’emploi
ADTRAN
ADTRAN E1 Manuel utilisateur
ADTRAN
ADTRAN Total Access 850 Guide de l'utilisateur
ADTRAN
ADTRAN 1442351G7 Manuel utilisateur
ADTRAN
ADTRAN Total Access SHDSL LTU Mode d’emploi
ADTRAN
ADTRAN DDS T200 Mode d’emploi
ADTRAN
ADTRAN NetVanta 834 Manuel du propriétaire
ADTRAN
ADTRAN Stub Routing Manuel utilisateur
ADTRAN
ADTRAN IQ 310 Manuel utilisateur
ADTRAN
ADTRAN SLC-5 U-BR1TE III Mode d’emploi
ADTRAN
ADTRAN NetVanta E1/FE1 + G.703 Network Interface... Manuel utilisateur
ADTRAN
ADTRAN Total Access Octal ADSL Manuel utilisateur
ADTRAN
ADTRAN ATLAS 800 Series Module QUAD E1 Guide de l'utilisateur
ADTRAN
ADTRAN NETVANTA UNIFIED COMMUNICATIONS DEMO KIT Manuel utilisateur
ADTRAN
ADTRAN TSU 100 Manuel utilisateur
ADTRAN
ADTRAN Fractional T1 Tandem Channel Unit FT1-TDM Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
