ADTRAN DDS T200 Mode d’emploi

61212008L1-5C 61212008L1-5C, Issue 3 1

Section 61212008L1-5

Issue 3, August 1999

CLEI Code: NCM38CXBRA

DDSType 200 Dual Slot Housing

Installation and Maintenance

Contents

1. GENERAL .................................................................. 1

2. PHYSICAL DESCRIPTION ...................................... 1

3. INSTALLATION ........................................................ 2

4. CONNECTIONS ......................................................... 3

5. SPECIFICATIONS ..................................................... 3

6. MAINTENANCE ....................................................... 4

7. WARRANTY AND CUSTOMER SERVICE ........... 4

Figures

Figure 1. ADTRAN DDS T200 Dual Slot Housing ....... 1

Figure 2. T200 Housing Terminal Barrier Block ........... 2

Figure 3. T200 Housing Rear Panel................................ 2

Figure 4. Chassis Mounting Template ............................ 3

Tables

Table 1. Wiring Connections .......................................... 3

Table 2. Telecommunication Configuration Codes........ 3

Table 3. Specification ..................................................... 4

1. GENERAL

The ADTRAN DDS Type 200 Dual Slot Housing is

used to house one or two standard T200 circuit

packs, and is capable of performing loop

termination. Figure 1 is an illustration of the unit.

Basic Features

The basic features of the unit are listed below.

• Standalone Type 200 housing

• -48VDC power connections

• Network connection through a terminal

barrier strip

• Customer connects to RJ-48S or barrier

strip

• Durable, hinged metal enclosure

• Wraparound transparent front panel for easy

LED viewing

The DDS T200 Dual Slot Housing is designed to

accept any standard Type 200 plug-in card. For

non-loop powered units, the DDS T200 Dual Slot

Housing can provide power to the circuit card

through an external power supply. The ADTRAN

1353.DSK48V02 power supply can be used to

provide -48 VDC from standard 100-120 VAC to

power these cards.

The ADTRAN 1353.POWER08 supply can be used

to provide -48 VDC from standard 220 VAC. These

power supplies must be purchased separately. The

T200 Housing also provides network and customer

interface connections to the circuit card.

Revision History

This is the third release of this document. This

practice has been reissued to include

Telecommunication Configuration Codes and

methods for locally powering the unit.

2. PHYSICAL DESCRIPTION

Figure 1 illustrates the ADTRAN DDS T200 Dual

Slot Housing with the cover on. Connections are

made available by unscrewing the lock screw and

lifting the hinged cover.

Inside the housing are Euro-style connectors,

illustrated in Figure 2, for connecting to the

network, to the CPE, and to an external power

Figure 1. ADTRAN DDS T200 Dual Slot Housing

TOP SLOT - CIRCUIT 2

BOTTOM SLOT - CIRCUIT 1

TR DDS2

PART NUMBER

1212008

Trademarks: Any brand names and product names included in this document are

trademarks, registered trademarks, or trade names of their respective holders.

2 61212008L1-5C, Issue 3 61212008L1-5C

source, if one is used. A grounding lug is provided

for frame ground connections.

The rear panel of the T200 Dual Slot Housing

contains two slots with RJ-48S jacks for CPE

connections and a portal for network and power

connections, illustrated in Figure 3.

The T200 Dual Slot Housing is 2 inches high by 6

inches wide by 9 3/4inches deep, and weighs less

than 1␣ pound. It can be mounted on a desk, table, or

wall. The unit operating temperature range is -40°C

to +70°C.

3. INSTALLATION

After unpacking the unit, immediately inspect it for

possible shipping damage. If damage is discovered,

file a claim immediately with the carrier, then

contact ADTRAN Customer Service. (Refer to

subsection 7, Warranty and Customer Service.)

Components shipped with the unit include the

following:

• T200 chassis (including RJ-48S jack)

• Four #8 screws

• Wall mounting template

The T200 chassis is designed to be wall- or

desk-mounted. For wall mounting, four #8 screws

have been included. Select a suitable position on a

wall or desk for installation.

Figure 4 illustrates the mounting pattern in the base

of the chassis. The four mounting screws should be

located as shown. Drive the screws into the

mounting surface, leaving a clearance of at least

1/4␣ inch, and no greater than 1/2inch.

A mounting template is provided with each unit to

assist in locating the drill holes. The template

attaches to the wall by a tape strip located across the

top of the template. Remove the template from the

wall after using.

Grounding Instructions (UL 1950)

In accordance with UL 1950, a supplemental earth

ground must be connected prior to connection of the

telecommunication wiring. The supplemental earth

ground connection shall be connected to the ground

lug.

Grounding instruction information from the

Underwriter’s Laboratory UL 1950 Standard for

Figure 3. T200 housing Rear Panel

CUSTOMER

CIRCUIT 1 CUSTOMER

CIRCUIT 2

NETWORK

R1 LOOP 1 TX T

TX R

RX T1

RX R1

K1K2

TX T

TX R

RX T1

RX R1

-48V

GND

T1 LOOP 1

R LOOP 2

T LOOP 2

R1 LOOP 1

T1 LOOP 1

R LOOP 2

TS2

TS4

T LOOP 2

CIRCUIT 2CIRCUIT 1

CUSTOMER

CIRCUIT 1CIRCUIT 2

D1 J2 20

Ckt 1 Ckt 2

Figure 2. T200 Housing Terminal Barrier Block

61212008L1-5C 61212008L1-5C, Issue 3 3

Safety (Telephone Equipment) is provided in the

following paragraphs.

In addition to the power supply grounding

conductor, an equipment supplementary grounding

conductor that is not smaller in size than the power

supply grounding conductors, must be installed

prior to connection of telecommunications wiring.

In addition, the connection to the ground of the

supplementary equipment grounding conductors

shall be in compliance with the rules for terminating

bonding jumpers in Part K of Article 250 of the

National Electrical Code ANSI/NFPA 70.

Termination of the supplementary equipment

grounding conductor is permitted to be made to

building steel, to a metal electrical raceway system,

or to any grounded item that is permanently and

reliably connected to the electrical service

equipment ground.

The attachment plug receptacles in the vicinity of

the product or system are all to be of a grounding

type, and the equipment grounding conductors

serving these receptacles are to be connected to

earth ground at the service equipment.

Bare, covered, or insulated grounding conductors

are acceptable. A covered or insulated grounding

conductor shall have a continuous outer finish that is

either green, or green with one or more yellow

stripes.

4. CONNECTIONS

The terminal barrier strip is used to make

connections to the housing. To connect to the

barrier strip, place conductor into the receptacle of

each terminal. The terminal strip is connected to the

card edge connector to interface the connections to

the circuit card. Figure 2 illustrates the pinout of the

card edge connector in relationship to the barrier

strip. The RJ-48 jack, along with the terminal strip,

provides for CPE connection. Table 1 shows the

wiring connections. Table 2 shows the

Telecommunication Configuration Codes.

Power

The T200 Dual Slot Housing is designed to house a

loop-powered or locally-powered circuit card. The

terminal barrier strip provides the ability to connect

an external -48 VDC supply to the circuit card. One

of the following methods shall be utilized when

locally powering the unit:

9.375"

4.5"

7.5"

1.5"

4.5"

Figure 4. Chassis Mounting Template

SDD LANGIS -ORUE ROTCENNOC

002T NIP REBMUN

krowteN

TTRT *TR *RR

2pooLT 2pooLR 1pooL1T 1pooL1R

1474

remotsuC

TTD RTD TRD RRD

TXT RXT 1TXR 1RXR

5594

hcaeRlatoTnidesutoN*

.snoitacilppa

Table 1. Wiring Connections

Code Input Output

IC E -

TC X X

PC F C

Table 2. Telecommunication Configuration

Codes

4 61212008L1-5C, Issue 3 61212008L1-5C

• Connect to a reliably grounded -48 VDC

source which is electrically isolated from

the AC source.

• A readily accessible disconnect device, that

is suitably approved and rated, shall be

incorporated in the fixed wiring.

• The branch circuit overcurrent protection

shall be a fuse or circuit breaker rated

minimum 48 V, maximum 20 A.

• The unit shall be installed in accordance

with the requirements of NEC NFPA 70.

• Connect to a Class 2 Type power supply

rated 48 VDC, maximum 240 VA.

These connections are made to the -48V and GND

on the barrier strip, as illustrated in Figure 2.

Connection from the barrier strip to the edge card

connector is illustrated in Figure 2. A ground lug

(P1), illustrated in Figure 2, is provided to connect

an external frame ground wire to the unit.

5. SPECIFICATIONS

The specifications for the ADTRAN T200 Dual Slot

Housing are listed in Table 3.

6. MAINTENANCE

The ADTRAN T200 Dual Slot Housing requires no

routing maintenance to operate properly. In case of

equipment failure, remove the unit and replace it

with another unit optioned in an identical manner.

ADTRAN does not recommend that repairs be

performed in the field. Repair services may be

obtained by returning the defective unit to

ADTRAN.

7. WARRANTY AND CUSTOMER SERVICE

ADTRAN will replace or repair this product within

10 years from the date of shipment if it does not

meet its published specifications or fails while in

service (see ADTRAN Carrier Network Equipment

Warranty, Repair, and Return Policy and Procedure,

document 60000087-10A).

Mechanical

Size ....................................... 6" wide by 9 3/4" deep by 2"

high

Weight .................................. Less than 1 lb.

Mounting .............................. Tabletop or wall-mount

Environment

Temperature ......................... Operating: -40°C to +70°C

Storage: -40°C to +85°C

Relative Humidity ................ Up to 95% non-condensing

Table 3. Specifications

Contact Customer and Product Service (CAPS)

prior to returning equipment to ADTRAN.

For service, CAPS requests, or further information,

contact one of the following numbers:

ADTRAN Sales

Pricing and availability

(800) 827-0807

ADTRAN Technical Support

Presales Applications / Post-sale Technical

Assistance

(800) 726-8663

Standard support hours:

Monday-Friday, 7 a.m. - 7 p.m. CST

Emergency support: 7 days/week, 24 hours/day

ADTRAN Repair/CAPS

Return for repair / upgrade

(256) 963-8722

Repair and Return Address:

ADTRAN, Inc.

Customer and Product Support (CAPS)

901 Explorer Boulevard

Huntsville, Alabama 35806-2807

Autres manuels ADTRAN Matériel réseau

ADTRAN

ADTRAN DS3 NIU3 Manuel utilisateur

ADTRAN

ADTRAN SHDSL V.35 LTU Manuel utilisateur

ADTRAN

ADTRAN NetVanta 838 Manuel d'utilisation

ADTRAN

ADTRAN NetVanta SHDSL Network Interface Module Manuel utilisateur

ADTRAN

ADTRAN 411 Manuel utilisateur

ADTRAN

ADTRAN TRACER 4x06 Manuel de référence

ADTRAN

ADTRAN Total Access 300 Series Manuel du produit

ADTRAN

ADTRAN TSU ESP Manuel utilisateur

ADTRAN

ADTRAN 1200630L1 Manuel utilisateur

ADTRAN

ADTRAN Total Access 300 Series Manuel utilisateur

ADTRAN

ADTRAN ESU 120e Manuel utilisateur

ADTRAN

ADTRAN Network Interface Module T1/FT1 Manuel utilisateur

ADTRAN

ADTRAN 1202295L1 Manuel utilisateur

ADTRAN

ADTRAN TOTAL ACCESS 600R Manuel utilisateur

ADTRAN

ADTRAN MX410 Manuel utilisateur

ADTRAN

ADTRAN 834-5 Manuel utilisateur

ADTRAN

ADTRAN Total Access 850 Mode d’emploi

ADTRAN

ADTRAN NETVANTA OCTAL POE Manuel utilisateur

ADTRAN

ADTRAN Quad T1 IMA Mode d’emploi

ADTRAN

ADTRAN Total Access DSLAM 16-Port ADSL2+ Access Module... Manuel utilisateur

ADTRAN

ADTRAN AOC QSFP28 100G AOC QSFP28 100G 3M Manuel utilisateur

ADTRAN

ADTRAN DSU IQ Manuel utilisateur

ADTRAN

ADTRAN Total Access 300 Mode d’emploi

ADTRAN

ADTRAN SFP+ Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur