ACU-RITE 01536 Manuel utilisateur

Instruction Manual

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Questions? Contact Customer Support at

(877) 221-1252 or visit www.AcuRite.com.

CONTENTS

Unpacking Instructions ........... 2

Package Contents .................. 2

Product Registration ............... 2

Features & Benets: 5-in-1....... 3

Features & Benets: Display.... 4

Setup .................................... 7

5-in-1 Sensor Setup ................ 7

Display Setup ........................ 8

Set the Time, Date & Units ...... 9

Backlight Settings................... 9

Placement Guidelines ............10

5-in-1 Sensor Installation........ 11

Using the Weather Center .....12

PC Connect...........................13

Weather Underground ..........13

Rainfall Tracking ...................14

Weather Ticker .....................15

Programmable Alarms...........16

Troubleshooting ....................17

Care & Maintenance............ 20

Calibration .......................... 20

Specications....................... 22

FCC Information .................. 22

Customer Support ................ 23

Warranty............................. 23

Professional Weather Center

model 01536 / 8900123

IT FEELS LIKE 46OUTSIDE

Congratulations on your new AcuRite product. To ensure the best

possible product performance, please read this manual in its entirety

and retain it for future reference.

Unpacking Instructions

Remove the protective lm that is applied to the LCD screen prior to using this

product. Locate the tab and peel off to remove.

Package Contents

1. Display with Tabletop Stand

2. 5-in-1 Sensor

3. Sensor Mounting Bracket

4. Mounting Hardware

5. Power Adapter

6. USB Cable

7. 4 Alkaline Batteries

8. Instruction Manual

PRODUCT REGISTRATION

www.AcuRite.com

IMPORTANT PRODUCT MUST BE REGISTERED

TO RECEIVE WARRANTY SERVICE

Features & Benets

5-in-1 SENSOR

1. Rainfall Collector Funnel

2. Solar Cell Panel

Converts sunlight into power to run

internal aspirating fan.

Internal Aspirating Fan

(not shown)

Draws ambient air into

sensor to reduce solar radiation

heating, resulting in more accurate

temperature measurement.

3. A-B-C Switch

ID code that must match display’s

A-B-C switch to ensure units

synchronize.

4. Battery Compartment

5. Temperature & Humidity Sensors

(internal)

6. Mounting Point

7. Wind Speed Anemometer

8. Wind Direction Vane

9. Mounting Bracket

10. Mounting Hardware

Includes 5 anchors & the following

screws:

Qty Diameter Length

5 #4 3/4”

1 #4 1/2”

1 #6 1/2”

11. Debris Filter

Pre-installed to prevent debris from

entering the rain gauge.

IT FEELS LIKE 46OUTSIDE

Features & Benets

Display

1617181920212223

132 4 5

1. Current Wind Direction

2. Previous 2 Wind Directions

3. Seasonal Display

Heat Index calculation displays when

temperature is 80°F (27°C) or higher.

Dew Point calculation displays when

temperature is 79°F (26°C) or below.

Wind chill calculation displays when

temperature is 40°F (4°C) or lower.

4. Button

For momentary backlight and dimmer

settings.

5. Current Wind Speed

6. Rainfall

Displays most recent rainfall total

(today, this week or this month).

7. Rainfall History

Displays historical rainfall totals

(see page 14).

8. Indoor Indicator

Indicates indoor (display unit)

conditions are being shown.

9. Current Temperature for #8 or #12

Arrow icon indicates direction

temperature is trending.

10. Add-On Sensor Signal Strength

If applicable (see page 13).

11. Auto-Cycle Indicator

Indicates auto-cycle mode is enabled. If

applicable (see page 13).

12. Add-On Sensor Indicator

If applicable (see page 13).

13. Humidity Level Indicator

Indicates a high, low, or ideal humidity

comfort level.

14. Current Humidity for #8 or #12

Arrow icon indicates direction humidity

is trending.

15. Date

16. Button

Press to view rainfall records (#6 and #7).

17. Display Low Battery Icon

18. Peak Wind Speed

Highest speed from the last 60 minutes.

19. Button

For setup preferences and manually

cycling through Weather Ticker messages

(when display is not connected to

additional sensors). For manually cycling

add-on sensor data (when display is

connected to additional sensors).

20. Button

For setup preferences.

21. Clock

22. Button

For setup preferences and manually

cycling through Weather Ticker messages

(when display is not connected to

additional sensors). For manually cycling

add-on sensor data (when display is

connected to additional sensors).

23. Button

For alarm setup preferences.

24. Weather TickerTM

Streams real-time data (see page 15).

25. 5-in-1 Sensor Signal Strength

26. Sensor Low Battery Icon

27. Icon

Indicates display is in auto-dimming

brightness mode (see page 9).

28. Barometric Pressure

Arrow icon indicates direction pressure

is trending.

29. Average Wind Speed

Average wind speed over the past

2 minutes.

30. 12 to 24 Hour Weather Forecast

Self-Calibrating Forecasting pulls data

from your 5-in-1 sensor to generate

your personal forecast.

31. Learning Mode Icon

Disappears after weather forecast

self-calibration is complete (see page 12).

32. High/Low Humidity Records

Highest and lowest outdoor humidity

recorded since midnight.

33. Current Outdoor Humidity

Arrow icon indicates direction humidity

is trending.

34. High/Low Temperature Records

Highest and lowest outdoor temperature

recorded since midnight.

35. Current Outdoor Temperature

Arrow icon indicates direction

temperature is trending.

Back of Display

BACK OF DISPLAY

1. Plug-in for Power Adapter

2. Plug-in for USB Cable

3. Integrated Keyhole

For easy wall mounting.

4. DEVICE ID

12 digit unique ID required for

online connectivity functions.

5. Backup Battery Compartment

6. A-B-C Switch

ID code that must match 5-in-1

sensor’s A-B-C switch to ensure

units synchronize.

7. CLEAR RECORD / RESET Button

Press and HOLD for 8 seconds

to clear all records. Press and

HOLD for 10 seconds for full

reset to factory defaults.

8. Power Adapter

9. USB Cable for PC Connection

10. Battery Compartment Cover

(not shown)

############

DEVICE ID

01536-RX

RX : DC 4.5V 3x AA

AC/DC ADAPTER INPUT : 100-240AC 50-60Hz

OUTPUT: 5.0V 250mA

CAN RSS-Gen/CNR-Gen

MODEL : 01536CDI

Dew Point

Point De Rosée

Wind Chill

Refroidissement Éolien

SETUP

5-in-1 Sensor Setup

Set the A-B-C Switch

Locate the A-B-C switch inside the

battery compartment. Set the A-B-C

switch to A, B or C. You must select

the same letter choices for both the

sensor and the display in order for

the units to synchronize.

Install or Replace Batteries

Batteries MUST be installed for

this product to operate. AcuRite

recommends high quality alkaline

or lithium batteries for the best

product performance. Heavy duty

or rechargeable batteries are not

recommended.

The 5-in-1 sensor requires lithium

batteries in low temperature

conditions. Cold temperatures can

cause alkaline batteries to function

improperly. Use lithium batteries in

the 5-in-1 sensor for temperatures

below -4ºF/-20ºC.

1. Slide off the battery

compartment cover.

2. Insert 4 x AA batteries into the

battery compartment, as

shown. Follow the polarity

(+/-) diagram in the battery

compartment.

3. Replace the battery cover.

Remove Rain Gauge Stabilizer

Locate and remove the rain gauge

stabilizer (plastic tab) taped into

the bottom of the sensor. The rain

gauge will not function until this is

removed.

A B C

1A-B-C Switch

Set to match

display

2Install Batteries

4 AA Batteries

3Rain Gauge Stabilizer

Remove and discard

NOTE: If add-on sensors are being used with the display (see page 12), set them up at this

time. If pairing more than one wireless sensor with the display, the A-B-C channel must differ

between each add-on sensor. The display will automatically begin searching for add-on sensors

during initial setup.

Display Setup

Set the A-B-C Switch

The A-B-C switch is located inside

the battery compartment. It can

be set to A, B or C. However, you

must select the same letter choices

for both the 5-in-1 Sensor and the

display in order for the units to

synchronize.

Plug Power Adapter into

Electric Outlet

Write Down the DEVICE ID

12 digit unique ID needed for

online connectivity functions.

Install or Replace Backup

Batteries (optional)

Insert 3 x AA alkaline batteries into

the battery compartment, as shown.

Follow the polarity (+/-) diagram in

the battery compartment.

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE

WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to

be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of

used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries

in re, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT

recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.

IMPORTANT: Batteries are a backup

power source to preserve records

in the event of a power outage.

Power adapter is the recommended

primary power source to enjoy the

full functionality of this product.

24 C8 6E

4Install Backup

Batteries

3 AA Batteries

3Write Down

DEVICE ID

12 digit number

1A-B-C Switch

set to match

5-in-1 Sensor

2Plug in Power

Adapter

A B C

Set the Time, Date & Units

The display will automatically enter SET MODE after the unit has powered on.

Once in set mode, the preference you are currently setting will blink on the

display.

To adjust the currently selected (ashing) item, press and release the “ “ or

“ “ buttons (press and HOLD to fast adjust).

To save your adjustments, press and release the “ ” button again to adjust

the next preference. The preference set order is as follows:

LANGUAGE (English, French)

TIME ZONE (EST, CST, MST, PST, AKT, HAT, NST, AST)

AUTO DST CHANGE (YES, NO)*

WEATHER TICKER SPEED (SLOW, MEDIUM, FAST)

CLOCK HOUR

CLOCK MINUTE

CALENDAR MONTH

CALENDAR DATE

CALENDAR YEAR

TEMPERATURE UNITS (°F or °C)

WIND SPEED UNITS (mph, km/h, knots)

RAINFALL UNITS (inches or mm)

PRESSURE UNITS (inHg or hPa)

*If you live in an area that observes Daylight Saving Time, DST should be set

to YES, even if it is not currently Daylight Saving Time.

You will automatically exit SET MODE if no buttons are pressed for 20 seconds.

Enter setup mode at any time by pressing the “ ” button.

Display Backlight Settings

This weather station’s color display features three different lighting settings:

High (100%) brightness, Medium (60%) brightness and Low (15%) brightness.

Using battery power alone, the backlight is available momentarily for 10

seconds by pressing the “ ” button.

When display is powered with the power adapter, backlight remains on at

100% brightness. Press the “ ” button once to dim to 60% brightness. Press

again to dim to 15%. Press a 3rd time to enter “AUTO DIM” mode. The “ ”

icon appears to the left of the time to indicate that auto-dim mode is ON.

NOTE: Pressing and holding the “ ” button for 5 seconds will disable the

backlight. Once any button is pressed, the backlight will return to your selected

setting.

AUTO DIM MODE: Automatically adjusts display brightness based on time of day.

6:00 a.m. - 9:00 p.m. = 100% brightness

9:01 p.m. - 5:59 a.m.= 15% brightness

Placement for Maximum Accuracy

AcuRite sensors are sensitive to surrounding environmental conditions. Proper

placement of both the display and the sensor are critical to the accuracy and

performance of this product.

Display Placement

Place the display in a dry area free of dirt and dust. To ensure

accurate temperature measurement, place out of direct sunlight

and away from heat sources or vents. Display stands upright for

tabletop use or is wall-mountable.

5-in-1 Sensor Placement

The 5-in-1 sensor is designed to remain outdoors all year long.

Choose an open location with no obstructions above or around

the sensor for the most accurate measurements.

Important Placement Guidelines

Display and sensor must be within 330 feet (100 meters) of each other.

MAXIMIZE WIRELESS RANGE

Place units away from large metallic items, thick walls, metal surfaces, or other

objects that may limit wireless communication.

PREVENT WIRELESS INTERFERENCE

Place units at least 3 feet (.9 m) away from electronic devices (TV, computer,

microwave, radio, etc.).

LOCATE AWAY FROM HEAT SOURCES

Position sensor away from heaters, air conditioners, chimneys, exhaust vents,

asphalt and concrete (surfaces that radiate heat).

LOCATE AWAY FROM HUMIDITY SOURCES

Avoid installing the sensor near pools, spas, or other bodies of water. Water

sources may impact humidity accuracy.

LOCATE AWAY FROM SPRINKLER HEADS

DO NOT install the sensor where it will be sprayed by a sprinkler system. This

may force water inside the sensor.

LOCATE AWAY FROM WIND & RAIN OBSTRUCTIONS

DO NOT mount the sensor with obstructions around it.

Consider a location that is a wide open area, with few

structures around to ensure accurate wind measurement.

Visit us online to view installation photos and

video, or learn more about AcuRite technology:

www.AcuRite.com/5in1

IT FEELS LIKE 46OUTSIDE

View Video

Table des matières

Autres manuels ACU-RITE Station météorologique

ACU-RITE

ACU-RITE 01129 Manuel utilisateur

ACU-RITE

ACU-RITE 02099 Manuel utilisateur

ACU-RITE

ACU-RITE 01121 Manuel utilisateur

ACU-RITE

ACU-RITE 01525 Manuel utilisateur

ACU-RITE

ACU-RITE 11132-1500RX Manuel utilisateur

ACU-RITE

ACU-RITE 02007/06035RM Manuel utilisateur

ACU-RITE

ACU-RITE 06095 Manuel utilisateur

ACU-RITE

ACU-RITE 1036 Manuel utilisateur

ACU-RITE

ACU-RITE 433981 Manuel utilisateur

ACU-RITE

ACU-RITE 1502RX Manuel utilisateur

ACU-RITE

ACU-RITE OO592W Manuel utilisateur

ACU-RITE

ACU-RITE 00899 Manuel utilisateur

ACU-RITE

ACU-RITE Air 01412M Manuel utilisateur

ACU-RITE

ACU-RITE 02038 Manuel utilisateur

ACU-RITE

ACU-RITE 06101M Manuel utilisateur

ACU-RITE

ACU-RITE 01518 Manuel utilisateur

ACU-RITE

ACU-RITE 1506 Manuel utilisateur

ACU-RITE

ACU-RITE 01021 Manuel utilisateur

ACU-RITE

ACU-RITE Iris 06014 Manuel utilisateur

ACU-RITE

ACU-RITE 02033 Manuel utilisateur

ACU-RITE

ACU-RITE 00875 Manuel utilisateur

ACU-RITE

ACU-RITE 06005RM Manuel utilisateur

ACU-RITE

ACU-RITE 06058 Manuel utilisateur

ACU-RITE

ACU-RITE 01202 Manuel utilisateur

Manuels Station météorologique populaires d'autres marques

Auriol

Auriol AHFL 433 A1 Manuel utilisateur

NexSens

NexSens G2-HYDROMET Manuel utilisateur

Hyundai

Hyundai WS 2202 Manuel utilisateur

IROX

IROX HBVR761 UV-X Manuel utilisateur

La Crosse Technology

La Crosse Technology C86371 Manuel utilisateur

ADE

ADE WS 1711 Manuel utilisateur

Auriol

Auriol z29592 Manuel utilisateur

Auriol

Auriol 296289 Manuel utilisateur

Hyundai

Hyundai WS 2266 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-2210 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-811561 Manuel utilisateur

Ventus

Ventus W177 Manuel utilisateur

National Geographic

National Geographic VA Colour RC Manuel utilisateur

Renkforce

Renkforce 1208067 Manuel utilisateur

Levenhuk

Levenhuk Discovery Report WA40 Manuel utilisateur

Instant Transmission

Instant Transmission MA 10410 Manuel utilisateur

Lutron Electronics

Lutron Electronics PHB-318 Manuel utilisateur

WAREMA

WAREMA EWFS Weather station eco Manuel utilisateur