ACTi Q960 Manuel utilisateur

People Counting Camera

Installation Guide

Q960, Q961, Q962

2019/08/02

www.acti.com

INSTALLATION GUIDE

The following documentation covers the installation and configuration of your

device.

NOTE: The accuracy of the analytics algorithm may be affected by different

environmental factors or inappropriate installation. Please follow the

procedures in this installation guide. ACTi will not be held liable for

inaccuracies resulting from the aforesaid causes.

Part 1: Installation Specification

Model and counting width

The counting width depends on the installation height. The recommended

installation height for dual-lens camera is less than 4.0m (13.1ft). The specific

corresponding relation shown below:

Model

Installation

height

（m/ft）

Max. counting

width

（m/ft）

Without

doorframe

With doorframe

Q960

2.5/8.2

1.8/5.9

Placed in the middle

0.68m(2.2ft)

to door

Placed in the middle

3.0/9.8

2.9/9.5

Placed in the middle

1.1m(3.6ft)

to door

Placed in the middle

3.5/11.5

4.0/13.1

Placed in the middle

1.52m(5.0ft)

to door

Placed in the middle

Q961

3.0/9.8

2.2/7.2

Placed in the middle

0.85m(2.8ft)

to door

Placed in the middle

3.5/11.5

3.1/10.2

Placed in the middle

1.17m(3.8ft)

to door

Placed in the middle

4.0/13.1

Placed in the middle

1.5m(4.9ft)

to door

Placed in the middle

Q962

4.0/13.1

2.8/9.2

Placed in the middle

1.05m(3.4ft)

to door

Placed in the middle

4.5/14.8

3.4/11.2

Placed in the middle

1.28m(4.2ft)

to door

Placed in the middle

5.0/16.4

4.0/13.1

Placed in the middle

1.5m(4.9ft)

to door

Placed in the middle

www.acti.com

INSTALLATION GUIDE

Package Contents

Camera

Mounting Base

Quick Start Guide

Screw Kit

Quick Start

Guide

www.acti.com

INSTALLATION GUIDE

Part 2: Installation Steps

1. Installation

Please pay great attention to the mounting position. Inappropriate mounting

position may cause loss of accuracy. The recommended mounting position is

shown below:

Horizontal sketch map of mounting position

Effect picture after installation

Notice: Avoid the reflective environment (ex: Marble floor)

Vertical sketch map of mounting position

www.acti.com

INSTALLATION GUIDE

Make sure the camera is mounted vertically above the passenger flow

(90°vertical by the ground), see picture below:

Passenger flow

（

perpendicular to the door

）

For some scenarios where there are multiple cameras, mount the cameras

according to two rules.

Rule one: If there are turnstiles, each camera should be mounted to monitor

certain turnstile

www.acti.com

INSTALLATION GUIDE

Rule two:If there is no turnstile, at first, mount the cameras in one line, and

make sure the cameras have the same focal length. Then, keep a proper

distance between each camera according to the overlap (see the yellow

area below) of the adjacent two cameras’ counting width. The suggested

overlapping length is between 0.2-0.5m.

Sketch map of multiple cameras installation

Notice

1) People flow should be in vertical up-and-down direction

Passenger flow in horizontal direction (wrong)

www.acti.com

INSTALLATION GUIDE

Passenger flow in slant direction (wrong)

Passenger flow in vertical up-and-down direction (right)

2) Passageway width should be within camera’s counting width

3) Avoid obstacles such glass door, shield door and turnstile that block the

camera. For Each divided passageway, mount one camera right above.

www.acti.com

INSTALLATION GUIDE

4) The camera should be mounted as close as possible to the passageway

without obstacle. Remove the obstacle or adjust the camera mounting position if

there is obstacle below the camera. Meanwhile, to prevent miscounting, if there’s

a sliding door onsite, make sure the trajectory of the sliding door does not

overlap the detection line. Otherwise, the counting number may be misled by the

door opening and closing

Too far away from the door / Obstacle below camera

Recommended installation

www.acti.com

INSTALLATION GUIDE

Configuration for single camera

Step 1: Enable People Counting: check [Configuration]-[People Counting]

-[Enable People Counting]

Step 2: Calibration- Select the green box, drag it to proper location and click

[Calibration]. After this, “Height” in the configuration page will refresh (close

to the real height). A red box, which means the counting scope, and yellow

detection line will turn up. The arrow shows the direction of entering. See

picture below:

Notice

If auto calibration fails, switch to [Manual] and input the measured “Height”,

then click [Calibration].

Step 3: Detection line: move the detection line to proper location, about 0.5m

to the door. Then adjust the length of detection line to the real door’s width by

dragging the detection line’s two ends. See picture below:

Notice:

You should make the whole detection line in the same ground level or it may

lose accuracy.

www.acti.com

INSTALLATION GUIDE

Step 4: Save configuration and test. After configuration, click [save] and test.

If miscounting happens, slightly adjust the detection line’s location and

length.

3. Configuration for multiple cameras

Step 1: Do configuration for each camera following the steps above

Step 2: Move each camera’s detection line and connect the ends of adjacent

lines. Some objects could be placed on the image border for reference. See

picture below:

Configuration of each detection line

Autres manuels pour Q960

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACTi Caméra de sécurité

ACTi

ACTi B94 Manuel utilisateur

ACTi

ACTi D41 Manuel utilisateur

ACTi

ACTi E38 Manuel utilisateur

ACTi

ACTi D61 Manuel utilisateur

ACTi

ACTi TCM-1011 Instructions d'utilisation

ACTi

ACTi ACM-3401 Series Instructions d'utilisation

ACTi

ACTi B96A Manuel utilisateur

ACTi

ACTi B74 Manuel utilisateur

ACTi

ACTi ACM-1100 Series Manuel utilisateur

ACTi

ACTi D41A Manuel utilisateur

ACTi

ACTi E31 Manuel utilisateur

ACTi

ACTi KCM-8111 Manuel utilisateur

ACTi

ACTi VER. 061030 CAM-6500 Instructions d'utilisation

ACTi

ACTi TCM-1231 Series Instructions d'utilisation

ACTi

ACTi D11 Manuel utilisateur

ACTi

ACTi TCM-5311 Guide de démarrage rapide

ACTi

ACTi A310 Manuel utilisateur

ACTi

ACTi KCM-5511 Instructions d'utilisation

ACTi

ACTi A3 Series Manuel utilisateur

ACTi

ACTi A4 Series Manuel utilisateur

ACTi

ACTi TCM-7411 Instructions d'utilisation

ACTi

ACTi Z810 Manuel utilisateur

ACTi

ACTi ACM-3701E Instructions d'utilisation

ACTi

ACTi ACM-3011 Instructions d'utilisation

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur