ACTi KCM-5211 Manuel utilisateur

KCM-5211

18x Zoom H.264 4-Megapixel IP D/N

PoE Box Camera

(DC 12V / PoE)

Ver. 2014/10/15

www.acti.com

KCM-5211 Hardware Manual

Table of Contents

Precautions 3

Safety Instructions ...........................................................................4

Introduction 6

Package Contents.............................................................................6

Physical Description ........................................................................7

Basic Connections .........................................................................10

Serial Port Connection................................................................. 11

Accessing the Camera 13

Configure the IP Address...............................................................13

Access the Camera.........................................................................17

www.acti.com

KCM-5211 Hardware Manual

Precautions

Read these instructions

You should read all the safety and operating instructions before using this product.

Heed all warnings

You must adhere to all the warnings on the product and in the instruction manual. Failure to

follow the safety instruction given may directly endanger people, cause damage to the system

or to other equipment.

Servicing

Do not attempt to service this video device yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

Trademarks

All names used in this manual are probably registered trademarks of respective companies.

Liability

Every reasonable care has been taken during the writing of this manual. Please inform your

local office if you find any inaccuracies or omissions. We cannot be held responsible for any

typographical or technical errors and reserve the right to make changes to the product and

manuals without prior notice.

FCC/CE Regulation

NOTE: This equipment has been tested and found to comply with the limits for a Class Adigital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the users will be required to correct the

interference at their own expense.

www.acti.com

KCM-5211 Hardware Manual

Safety Instructions

Don’t use the power supply with other voltages

This device is likely to be damaged or damage other equipments / personnel, if you use a

power supply with different voltage than the one included with this device. All warranty of this

product will be voided in the situations above.

Don’t open the housing of the product

Cleaning

Disconnect this video product from the power supply before cleaning.

Attachments

Do not use attachments not recommended by the video product manufacturer as they may

cause hazards.

Water and Moisture

Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,

or laundry tub, in a wet basement, or near a swimming pool and the like.

Don’t use accessories not recommended by the manufacturer

Only install this device and the power supply in a dry place protected from weather

Servicing

Do not attempt to service this video product yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

Damage Requiring service

Disconnect this video product from the power supply immediately and refer servicing to

qualified service personnel under the following conditions.

1) When the power-supply cord or plug is damaged

2) If liquid has been spilled, or objects have fallen into the video product.

3) If the video product has been directly exposed to rain or water.

4) If the video product does not operate normally by following the operating Instructions in

this manual. Adjust only those controls that are covered by the instruction manual, as an

improper adjustment of other controls may result in damage, and will often require

extensive work by a qualified technician to restore the video product to its normal

www.acti.com

KCM-5211 Hardware Manual

operation.

Safety Check

Upon completion of any service or repairs to this video product, ask the service technician to

perform safety checks to determine if the video product is in proper operating condition.

www.acti.com

KCM-5211 Hardware Manual

Introduction

Package Contents

KCM-5211 QIG

Product CD Terminal Blocks for Power, DI/O and

Serial Port

Accessories Warranty Card

*For the mounting block, please attach the flat side

towards the front of camera. There are two types of

mounting blocks, and this device uses the black

version.

www.acti.com

KCM-5211 Hardware Manual

Physical Description

1) Digital Input / Output

Used in applications like motion detection, event triggering, time lapse recording, alarm

notifications, etc., the I/O terminal connector provides the interface to:

•2 Transistor Outputs- For connecting external

devices such as relays and LEDs. Connected devices

can be activated by Output buttons on the Live View

page or through video management software. Connect

DO1 and DO2 to their closest 12V pin to activate.

•2 Digital Inputs- An alarm input for connecting devices that can toggle between an open

and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. The

device will detect the change in digital input and transmit the signal to video surveillance

servers. The I/O terminal pins are numbered right to left,

Connect input/output devices to the camera as follows:

1. Attach the cables for the device securely to the supplied green connector block. Connect DI

pins to GND pins, and DO pins to 12V pins. Link pins 1/3, 2/4, 5/7,6/8.

2. Once cables are connected, push connector block into the terminal connector on camera.

www.acti.com

KCM-5211 Hardware Manual

2) Serial Port

This port connects to serial devices via RS-485 or RS-422 protocols. Use the supplied serial

port terminal block to connect the wires from the camera to the serial device.

See Serial Port Connection on page 11 for connection details.

3) Ethernet Port

The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this

IP device can auto detect the speed of local network segment (10Base-T/100Base-TX

Ethernet).

4) Reset Button

Step 1: Switch off IP device by disconnecting the power cable

Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)

Step 3: Reconnect the power cable while continuing to hold the reset button. The red

Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for

another second and turn off again. By this time the reset to default operation is already

completed. This will take around 20 seconds from power up. You may then release the

reset button. This length of time fluctuates slightly with the environment. The Power LED light

will come back on and stay on after a few more seconds. The unit will start up with factory

default settings automatically.

FUSE 1A

NPN

DC TO DC

3.3V

DC POWER

GND 1

CONVERTER

EARTH GND

RELAY

DIODE

DEVICE

POWER INPUT

CAMERA

www.acti.com

KCM-5211 Hardware Manual

On (3s) On

Power On

About 20 Seconds

Stay On

Off (about 15s) Off (10~15s)

Restore to Default

Complete

5) Audio Input / Output

The IP device supports audio input and output with earphone jack

6) Micro SDHC Card Slot

Insert your Micro SDHC card here for local recording on camera

7) Power LED

This LED light will indicate current camera status.

8) Power Input

If you use Power Adaptor to run the device, please connect the power adaptor to the terminal

block in the way shown below.

www.acti.com

KCM-5211 Hardware Manual

Basic Connections

Follow the procedures below to connect the IP device to the respective apparatuses.

If you have a PoE(Power over Ethernet) supported switch or injector:

1) Connect your IP Box Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45

connector.

2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.

If your switch does not support PoE, and you are powering the camera with power

adaptor:

1) Connect the power adaptor to IP Box Camera

2) Connect IP device’s Ethernet port to Network switch (via RJ45 connectors).

Connect a PC to the Ethernet switch (via RJ45 connectors)

Please refer to our PoE Guide for more details on Power over Ethernet related concepts.

Autres manuels pour KCM-5211

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACTi Caméra IP

ACTi

ACTi CAM-7300 series Manuel utilisateur

ACTi

ACTi Indoor Dome Series E610 Manuel utilisateur

ACTi

ACTi ACM-4201 Manuel utilisateur

ACTi

ACTi ACM-4200 series Manuel utilisateur

ACTi

ACTi CAM-5200S Manuel utilisateur

ACTi

ACTi KCM-3911 Manuel utilisateur

ACTi

ACTi CAM-5120 Manuel utilisateur

ACTi

ACTi ACM-5801 Instructions d'utilisation

ACTi

ACTi TCM-56x1 series Manuel utilisateur

ACTi

ACTi CAM-5100M Manuel utilisateur

ACTi

ACTi ACM-1231 Instructions d'utilisation

ACTi

ACTi TCM-3111 Manuel utilisateur

ACTi

ACTi CAM-5100M Manuel utilisateur

ACTi

ACTi KCM-5311 Instructions d'utilisation

ACTi

ACTi ACM-4201 Manuel utilisateur

ACTi

ACTi KCM-3211 Manuel utilisateur

ACTi

ACTi ACM-1430 series Instructions d'utilisation

ACTi

ACTi ACM-3701E Manuel utilisateur

ACTi

ACTi TCM-1511 Instructions d'utilisation

ACTi

ACTi ACM-5611 Instructions d'utilisation

ACTi

ACTi ACM-8511 Manuel utilisateur

ACTi

ACTi TCM-4101 Instructions d'utilisation

ACTi

ACTi ACM-3401 Series Manuel utilisateur

ACTi

ACTi CAM-5200S Manuel utilisateur

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur