ACTi KCM-3911 Manuel utilisateur

KCM-3911

H.264 4-Megapixel IP D/N Hemispheric Camer

a with Advanced WDR

(DC 12V / PoE)

Hardware Manual

Ver. 2013/10/31

www.acti.com

KCM-3911 Hardware Manual

Table of Contents

Precautions 3

Safety Instructions ...........................................................................4

Introduction 6

Package Contents............................................................................. 6

Physical Description ........................................................................7

Before Installation 9

Unpack the Camera..........................................................................9

Prepare the Power Adaptor (Optional)..........................................10

Prepare the DI/DO Connector (Optional) ......................................12

Installation Procedures 15

Mounting Solutions ........................................................................15

Mounting on the Ceiling or Wall with the Base Plate................... 17

Step 1: Install the Base Plate.......................................................17

Step 2: Attach the Camera to the Base Plate...............................18

Step 3: Connect the Cables.........................................................19

Accessing Camera 21

Configure the IP Addresses...........................................................21

Access the Camera.........................................................................25

www.acti.com

KCM-3911 Hardware Manual

Precautions

Read these instructions

You should read all the safety and operating instructions before using this product.

Heed all warnings

You must adhere to all the warnings on the product and in the instruction manual. Failure to

follow the safety instruction given may directly endanger people, cause damage to the system

or to other equipment.

Servicing

Do not attempt to service this video device yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

Trademarks

All names used in this manual are probably registered trademarks of respective companies.

Liability

Every reasonable care has been taken during the writing of this manual. Please inform your

local office if you find any inaccuracies or omissions. We cannot be held responsible for any

typographical or technical errors and reserve the right to make changes to the product and

manuals without prior notice.

FCC/CE Regulation

NOTE: This equipment has been tested and found to comply with the limits for a Class Adigital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the users will be required to correct the

interference at their own expense.

www.acti.com

KCM-3911 Hardware Manual

Safety Instructions

Don’t use the power supply with other voltages

This device is likely to be damaged or damage other equipments / personnel, if you use a

power supply with different voltage than the one included with this device. All warranty of this

product will be voided in the situations above.

Don’t open the housing of the product

Cleaning

Disconnect this video product from the power supply before cleaning.

Attachments

Do not use attachments not recommended by the video product manufacturer as they may

cause hazards.

Water and Moisture

Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,

or laundry tub, in a wet basement, or near a swimming pool and the like.

Don’t use accessories not recommended by the manufacturer

Only install this device and the power supply in a dry place protected from weather

Servicing

Do not attempt to service this video product yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

Damage Requiring service

Disconnect this video product from the power supply immediately and refer servicing to

qualified service personnel under the following conditions.

1) When the power-supply cord or plug is damaged

2) If liquid has been spilled, or objects have fallen into the video product.

3) If the video product has been directly exposed to rain or water.

4) If the video product does not operate normally by following the operating Instructions in

this manual. Adjust only those controls that are covered by the instruction manual, as an

improper adjustment of other controls may result in damage, and will often require

extensive work by a qualified technician to restore the video product to its normal

operation.

www.acti.com

KCM-3911 Hardware Manual

Safety Check

Upon completion of any service or repairs to this video product, ask the service technician to

perform safety checks to determine if the video product is in proper operating condition.

Caution: The base of the camera will be hot while camera is powered on!

(Please note that it is a NORMAL CONDITION for this model since the base is used as a heat

sink and all the camera functions will work normally!)

It is recommended to use mounting solution for installation.

Mounting Solutions

Flush

PMAX-1009

Wall

PMAX-0310

Pendant

PMAX-0101

PMAX-0103

Corner

PMAX-0101

PMAX-0303

PMAX-0402

Pole

PMAX-0101

PMAX-0303

PMAX-0502

Notice: Do NOT install this camera directly onto any surface (wall,

ceiling). Use the supplied base plate or one of the ACTi mounting

accessories, as listed above.

www.acti.com

KCM-3911 Hardware Manual

Introduction

Package Contents

Camera

Base Plate

Screw Kit

Network Cable

Audio Cable

Drill Template

Terminal Block

(for Power)

Terminal Block

(for DI/DO)

Quick Installation Guide

Warranty Card

Drill Template

www.acti.com

KCM-3911 Hardware Manual

Physical Description

Reset Button

Ethernet Port

Micro SDHC Card Slot

Digital Input / Output

Power LED

DC 12V Power Input

Audio Input / Output

1) Reset Button

The Reset Button is used to restore the factory default settings of the camera, including the

administrator’s password.

The reset button can be used for following purposes:

1. The administrator’s password has been forgotten and therefore the camera cannot be

accessed.

2. In case of IP address, mask, or allow/deny filter related issues, resulting with inability to

modify these settings.

3. In case of connectivity issues or abnormal video quality.

How to do the reset properly?

Step 1: Disconnect the power supply (e.g. disconnect the power adaptor or the high PoE

injector).

Step 2: Press and continue to hold the reset button (using a pointed object, such as a pen).

Step 3: Connect the power supply while keeping the reset button pressed. During this time the

Power LED may turn on and turn off several times.

Step 4: Wait for 45 seconds and release the reset button.

www.acti.com

KCM-3911 Hardware Manual

2) Micro SDHC Card Slot

Insert a Micro SDHC card here for local recording (Micro SDHC card not included in the

package).

3) Power LED

The Power LED lights up when the camera power is on.

4) Audio Input / Output

This connector connects to the bundled audio cable which provides 3.5mm audio input and

output jacks. See Step 3: Connect the Cables on page 19.

5) Ethernet Port

The Ethernet port connects to a network using a standard Ethernet cable.

6) Digital Input / Output

This connector connects to digital input or output devices, such as an alarm trigger, panic

button, etc. Digital Input (DI) and Digital Output (DO) devices are used in applications like

motion detection, event triggering, alarm notifications, etc. Please refer to Prepare the DI/DO

Connector (Optional) on page 12 for information on how to connect DI/DO devices to your

camera.

7) DC 12V Power Input

In case the camera is connected to a non-PoE (Power over Ethernet) switch, use this

connector to connect the camera to an external power adaptor. Please refer to Prepare the

Power Adaptor (Optional) on page 10 for information.

www.acti.com

KCM-3911 Hardware Manual

Before Installation

Unpack the Camera

1. Slightly twist the cover ring counter-clockwise and pull to detach it.

2. Remove the sticker label.

3. Set the camera aside for later installation.

www.acti.com

KCM-3911 Hardware Manual

Prepare the Power Adaptor (Optional)

The camera consumes 9.6W power when powered by a Power over Ethernet (PoE) switch

that is IEEE802.3af compliant. In case of using a non-PoE switch or your PoE switch has

limited power supply, you can purchase a power adaptor and directly connect the camera to a

power outlet. The power adaptor must be connected to the supplied terminal block before use.

To do this, follow the procedures below:

1. Loosen the screws of the 12V and GND pins of the power terminal block.

2. Take note that a standard power adaptor cable has two (2) different wires:

3. Connect the wire with the white stripe to the 12V pin and the other to the GND pin.

White stripe: Connects to 12V Pin

Connects to GND Pin

Autres manuels pour KCM-3911

Table des matières

Autres manuels ACTi Caméra IP

ACTi

ACTi ACM-4200 series Manuel utilisateur

ACTi

ACTi KCM-5211 Manuel utilisateur

ACTi

ACTi CAM-6200 Manuel

ACTi

ACTi ACM-4201 Instructions d'utilisation

ACTi

ACTi ACM-1511 Series Instructions d'utilisation

ACTi

ACTi TCM-4201 Manuel utilisateur

ACTi

ACTi CAM-5200S Manuel utilisateur

ACTi

ACTi ACM-4200 series Instructions d'utilisation

ACTi

ACTi ACM-1430 series Instructions d'utilisation

ACTi

ACTi ACM-4100 series Manuel utilisateur

ACTi

ACTi CAM-5100 Manuel du propriétaire

ACTi

ACTi TCM-4101 Instructions d'utilisation

ACTi

ACTi TCM-5311 Instructions d'utilisation

ACTi

ACTi CAM-7300 series Manuel utilisateur

ACTi

ACTi CAM-5300H Manuel utilisateur

ACTi

ACTi ACM-8511 Manuel utilisateur

ACTi

ACTi ACM-5601 Manuel utilisateur

ACTi

ACTi CAM-5120 Manuel utilisateur

ACTi

ACTi CAM-5100M Manuel utilisateur

ACTi

ACTi TCM-4101 Instructions d'utilisation

ACTi

ACTi CAM-7300 series Instructions d'utilisation

ACTi

ACTi ACM-1231 Instructions d'utilisation

ACTi

ACTi TCM-3111 Manuel utilisateur

ACTi

ACTi CAM-5100 Manuel utilisateur

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur