ACTi CAM-5200S Manuel utilisateur

CIF

80TVL

IP Camera

w/ Audio

CAM-5200S/CAM-5201S

Ver. 090302

Qui k Installation Guide

Table of Contents

1Getting Started _________________________________________________ 1-1

1.1 PACKAGE CONTENTS _________________________________________ 1-1

1.2 PHYSICAL DESCRIPTION ______________________________________ 1-2

1.3 CONNECT NECESSARY CABLES _______________________________ 1-6

2Quick Tour ____________________________________________________ 2-1

2.1 Configure the IP Camera _______________________________________ 2-1

2.1.1 Make sure network environment _________________________________________ 2-1

2.1.2 Open Internet Explorer with IP address____________________________________ 2-2

2.1.3 Login with default administrator’s account & password _______________________ 2-2

2.1.4 Preview the video ____________________________________________________ 2-3

2.1.5 Set the new IP address _________________________________________________ 2-4

2.1.6 Check Default Video Setting ____________________________________________ 2-5

2.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds for system

reboot. ___________________________________________________________________ 2-5

1-1

1 Getting Started

1.1 PACKAGE CONTENTS

CAM-5200S/5201S Warranty Card

Software CD Terminal Blocks for Power & DI/O

Power Adaptor (Option) Accessory

1-2

1.2 PHYSICAL DESCRIPTION

1. Microphone Input

Sensitivity: -44dB(0dB=1Vpp at 1KHz)

S/N Ratio: More than 58dB

Directivity: Omni directional

2. Auto Iris

Video / DC (switchable)

3. Video DC Level Adjustment

4. CCD Functions





Auto Electronic Shutter Speed Mode

AES On: 1/50 (60) sec. ~ 1/100,000 sec;

AES Off: 1/50 (60) sec.





Back Light Compensation

ON/OFF (Switchable)





Flickless

ON/OFF (Switchable)





Automatic Gain Control

ON/OFF (Switchable)





Auto White Balance

1-3

AWB / Push Lock WB Mode

5. WAN port

The IP Camera connects to the WAN (wide area network) via a

standard RJ45 connector. Supporting NWAY, this IP camera can

auto detect the speed of local network segment

(10Base-T/100Base-TX Ethernet). The WAN port is for FTTH

and can connect to a xDSL or cable modem.

With PoE built-in product, you can power the IP camera via

WAN port, LAN port or DC input. You can power the IP camera

with multiple power inputs at the same time. If you do, the IP

camera will gets the power from the first power input plugged into

it.

6. Power Input

DC 12V input.

PIN NAME DESCRIPTION

1 12V Power Input (DC +12V)

2 GND Ground Pin of Power Input

3 X No Connection

With PoE built-in product, you can power the IP camera via

WAN port, LAN port or DC input. You can power the IP camera

with multiple power inputs at the same time. If you do, the IP

NOTE: You may find a support package for help you

getting familiar with PoE. Please visit our web site, and

get the support document TS-00040.

1-4

camera will gets the power from the first power input plugged into

it.

7. Analog Video Output

The IP camera supports one channel analog video output.

8. LAN port

The IP Camera connects to the LAN (local area network) via a

standard RJ45 connector. Supporting NWAY, this IP camera can

auto detect the speed of local network segment

(10Base-T/100Base-TX Ethernet).

With PoE built-in product, you can power the IP camera via

WAN port, LAN port or DC input. You can power the IP camera

with multiple power inputs at the same time. If you do, the IP

camera will gets the power from the first power input plugged into

it.

NOTE: You may find a support package for help you getting familiar

with PoE. Please visit our web site, and get the support document

TS-00040.

9. Reset Button

Step 1: Switch off IP camera by disconnecting the power cable

Step 2: Using a suitable pointed object, press and continue to hold the

Reset Button depressed. While continuing to hold the reset button

depressed, reconnect the power cable.

Step 3: Keep holding the reset button depressed around 6 seconds,

release the reset button. The unit will start up with factory default

settings.

10. Action LED Indicator

The LED will light up after IP camera has successfully completed

the boot process.

11. DI/O

The IP Camera supports one alarm input and one alarm output.

DI:Logic Level 0: 0~0.4V; Logic Level 1: 3.3~30V

DO:Logic Level 0: 0.1~0.6V; Logic Level1: 2.4~5V

NOTE: You may find a support package for help you getting familiar

with PoE. Please visit our web site, and get the support document

TS-00040.

1-5

PIN NAME DESCRIPTION

1 GND Ground Pin

2 DI Digital Input

3 GND Ground Pin

4 DO Digital Output

1-6

1.3 CONNECT NECESSARY CABLES

The Ethernet cable and power cable are necessary for previewing function.

Make sure all cables are correctly and firmly connected.

1. Connect an analog monitor to IP Camera video out (BNC connector).

2. Connect the power adaptor to IP Camera

3. Connect IP Camera’s LAN port to an Ethernet (RJ45 connectors). If your

IP camera has PoE built-in, you can regard it as a PD and connect it

directly to a PSE device like PoE switch.

4. Connect a PC to the Ethernet hub (RJ45 connectors)

NOTE: You may find a support package for help you getting familiar

with PoE. Please visit our web site, and get the support document

TS-00040.

2-1

2 Quick Tour

This section guides you with a quick tour on IP camera.

2.1 Configure the IP Camera

2.1.1 Make sure network environment

Default IP of IP camera is 192.168.0.100. Please make sure IP camera and

your PC are on the same network segment before running the installation.

Please set the settings as below.

IP address: 192.168. 0.xxx

Subnet mask: 255.255.255. 0

(NOTE: xxx should be a number

from 1 to 254, but 100 is

excepted.)

2-2

2.1.2 Open Internet Explorer with IP address

NOTE: If your web browser is earlier than IE6, then download IE6 is

recommended.

NOTE: The IP camera default IP address is set to 192.168.0.100

2.1.3 Login with default administrator’s account & password

NOTE: Default administrator account is set to Admin, password is set to

123456, and click button.

Autres manuels pour CAM-5200S

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ACTi Caméra IP

ACTi

ACTi CAM-7300 series Instructions d'utilisation

ACTi

ACTi CAM-5100M Manuel utilisateur

ACTi

ACTi KCM-3211 Manuel utilisateur

ACTi

ACTi TCM-1511 Instructions d'utilisation

ACTi

ACTi Indoor Dome Series E610 Manuel utilisateur

ACTi

ACTi ACM-3701E Manuel utilisateur

ACTi

ACTi TCM-4101 Instructions d'utilisation

ACTi

ACTi ACM-8511 Manuel utilisateur

ACTi

ACTi KCM-7911 Manuel utilisateur

ACTi

ACTi ACM-8511 Manuel utilisateur

ACTi

ACTi CAM-5120 Manuel utilisateur

ACTi

ACTi ACM-1511 Series Instructions d'utilisation

ACTi

ACTi ACM-4200 series Instructions d'utilisation

ACTi

ACTi TCM-4101 Instructions d'utilisation

ACTi

ACTi CAM-5300H Manuel utilisateur

ACTi

ACTi CAM-5200S Manuel utilisateur

ACTi

ACTi CAM-5100 Manuel du propriétaire

ACTi

ACTi CAM-5120 Manuel utilisateur

ACTi

ACTi ACM-1432 Instructions d'utilisation

ACTi

ACTi TCM-5611 Series Manuel utilisateur

ACTi

ACTi ACM-4201 Manuel utilisateur

ACTi

ACTi ACM-5811 series Manuel utilisateur

ACTi

ACTi ACM-1310 series Manuel utilisateur

ACTi

ACTi ACM-4100 series Manuel utilisateur

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur