ACME IP Cabin AR-01 Manuel utilisateur

Contents

1. Safety Instructions.................................................................................................. 2

2. Technical Specifications .......................................................................................... 3

3. Fixture Function ..................................................................................................... 4

3.1 Control Panel.................................................................................................... 4

3.2 Main Function .................................................................................................. 6

4. Mounting the fixture .............................................................................................. 6

5. Troubleshooting ..................................................................................................... 9

6. Fixture Cleaning and Routine Maintenance.......................................................... 10

1. Safety Instructions

WARNING

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

Ensure all bolts and terminals are tight and clean.

Never leave the fixture unattended when open

Do not touch the heater unless you can be sure that it is cool.

Observe all warning labels in the enclosure itself.

Do not open the fixture in wet weather.

Always lift from under the base.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage may cause electric shock.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Please read the instructions carefully which includes important information

about the installation, operation and maintenance.

2. Technical Specifications

Control:

Control Modes: DMX, Wireless control (Optional)

Software upgrade:Firmware update via DMX link

Construction:

Display: Blue/White LCD Touch-panel Display

Data In/Out: 3-pin IP rated connectors

Power In/Out: IP rated power connectors

Protection rating: IP54

Power Voltage: AC 250V, 50Hz

Power Consumption: 430W

Ambient Temperature: -20℃~ 35 ℃

Weight: 6Kgs (Ball)

18.2Kgs (Base)

Dimension: 690 × 690 × 958mm

3. Fixture Function

3.1 Control Panel

1. DISPLAY:

It will show the fixture’s information on the display.

(the fixture temperature is 23 ℃)

(the current humidity is 65％)

(the electronic current is 3430mA)

(the current voltage is 218V)

LED INDICATORS (LED 1~6):

2. HEATER (LED 1) (Red):

When the fixture is in heating state, LED 1 ON;

3. FAN (LED 2) (Red):

When the fans in the fixture works, the LED 2 ON；

(Notice: Because the fans will begin working while the fixture is connecting to power supply, So

the LED 2 may be reserved for another functions)

4. LAMP ON (LED 3) (Orange):

When the fixture runs normally, the LED 3 ON;

5. LAMP RELAY (LED 4) (Orange):

When the fixture connects to unit, the LED 4 ON;

6. TEMP (LED 5) (Green):

When the internal current, voltage, temperature or humidity of the fixture is over its standard，

the LED 5 ON;

Notice: When the internal environment of fixture meets one of the following conditions, the unit

in the fixture will be Lamp OFF:

a. Input Voltage: ＞264V or ＜196V;

b. Electronic Current: ＞6A;

c. Humidity: ＞90%;

d. Temperature: ＞55 ℃.

When all the internal environment of fixture must meet the following conditions, the unit in the

fixture can be Lamp ON only:

a. Input Voltage: 206V ~ 255V;

b. Electronic Current: ≤5A;

c. Humidity: ≤80%；

d. Temperature: ≤50℃.

7. DMX (LED 6) (Green):

When the fixture received the DMX signal, the LED 6 ON;

8. FUNCTION BUTTONS:

MENU To select the programming functions

To go backward in the selected functions

To go forward in the selected functions

ENTER To confirm the selected functions

3.2 Main Function

Enter MENU mode, use /buttons select the Voltage Revise, Lamp On/Off or Machine

Version, and press the ENTER button to confirm. Then use /buttons to setup the selected

functions, and press the ENTER button to store.

4. Mounting the fixture

The following is the install instructions, please read it carefully for safe operations:

1. At first, you should loosen the 6 fast locks as the arrow direction, remove the Dome and place it

in a safety location;

2. Secondly, please loosen the Thumb screws and take out the Fast Lock Wrench, then use it to

loosen the 6 Quick Lock screws as the arrow direction, lift the Main Support Horizontal Plate

from the base;

3. Now, please lock the unit on the Main Support Horizontal Plate, make sure the horizontal plate is

tightly locked on the Omega clamps of the unit base;

4. Then use the Fast Lock Wrench locked the 6 Quick Lock screws;

5. Finally, please cover the Dome on the fixture, and lock the 6 fast locks tightly.

5. Troubleshooting

This is a guide to the general symptoms, problems, and solutions that may occur during the lifetime

of your enclosure. However, it is important to remember that problems may occur within

the unit

itself and these must also be considered.

A. Unit does not have power

Check power switch of unit. (Note: the following actions should be performed by a licensed

electrician) If power is on, check wiring (including metering supply voltages). If LEDs on the control

panel controller are lit, check the Lamp Relay LED. If it is on, meter power in receptacle. If no power

is present at the receptacle, contact technical support.

In case of over-temperature, the power disconnection is an intended function of the enclosure and

is for the protection of the unit, which is not meant to operate in extreme conditions. In this case,

the problem will only continue until temperature drops to acceptable levels. It is

possible that the

air intake or exhaust has become clogged, leading to higher temperatures

inside the enclosure.

Make sure that these areas are clear, the filters are clean, and the fans are working properly.

B. Unit turns on and off repeatedly

Check that vent areas and airways are clear. If so, ambient temperature may be too high (see

over-temperature note above) or unit may have internal problem.

C. Unit does not respond to DMX signal.

Make sure that unit has power. If so, check DMX wiring. If not, see above.

1. Fans are not spinning.

Fan cords may have become disconnected. Check connections between fan and cord.

Fans may be obstructed. Shut off power to enclosure and check for obstructions. Turn power back

on to see if fans will start spinning. If fans do not turn and display on temperature controller is lit,

contact technical support. If fans do not turn display is not lit, then enclosure is

not receiving

power. Turn off all power and check wiring. If the wiring is correct, contact technical support.

Table des matières

Autres manuels ACME Équipement d'éclairage

ACME

ACME LED-WAV-10W Manuel utilisateur

ACME

ACME Thunderroar Manuel utilisateur

ACME

ACME TOUR PIXEL BAR 1010 II Manuel utilisateur

ACME

ACME Dragon Scan 50 LED-SC50B Manuel utilisateur

ACME

ACME ANIMA C Manuel utilisateur

ACME

ACME Diabolo Manuel utilisateur

ACME

ACME Spider FC Manuel utilisateur

ACME

ACME STAGE PAR 100 COLOUR IP Manuel utilisateur

ACME

ACME Splendor 220 II Manuel utilisateur

ACME

ACME Sunrise Manuel utilisateur

ACME

ACME Inferno Manuel utilisateur

ACME

ACME STAGE PAR 400 ZOOM IP Manuel utilisateur

ACME

ACME Solar Flare Manuel utilisateur

ACME

ACME SABER HYBRID PRO Manuel utilisateur

ACME

ACME Gemini Manuel utilisateur

ACME

ACME LED Move 600SE Manuel utilisateur

ACME

ACME TRACK 10 Manuel utilisateur

ACME

ACME RAYZOR HYBRID Manuel utilisateur

ACME

ACME BRIGHT Manuel utilisateur

ACME

ACME Solaris Manuel utilisateur

ACME

ACME Whack Manuel utilisateur

ACME

ACME DELUGE LED-WAV-50W Manuel utilisateur

ACME

ACME LED-SC25 Manuel utilisateur

ACME

ACME LED-PS10D RGBW Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur