ACME LED-MS150 Manuel utilisateur

LED-MS150

User Manual

Please read the instruction carefully before use

CONTENTS

1. Safety Instruction ................................................................................................... 2

2. Technical Specifications .......................................................................................... 3

3. How To Set The Unit ............................................................................................... 4

3.1 Fixture Overview .............................................................................................. 4

3.2 Gobo Wheel ..................................................................................................... 6

3.3 Main Function .................................................................................................. 6

3.4 Home Position Adjustment............................................................................. 12

4. How to Control the Unit ....................................................................................... 13

4.1 Master/Slave Built In Preprogrammed Function............................................. 13

4.2 Easy Controller ............................................................................................... 14

4.3 DMX Controller............................................................................................... 14

5. DMX512 Configuration ......................................................................................... 15

6. DMX Connection .................................................................................................. 19

7. Troubleshooting ................................................................................................... 20

8. Fixture Cleaning ................................................................................................... 21

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction manual.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type

spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

Please read the instruction carefully which includes important

information about the installation, usage and maintenance.

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Technical Specifications

◇ompact moving spot with powerful output,perfect for clubs,bars,discotheques,mobie DJs.

◇MX Channel: 8/1 0 Ch

◇Control modes: DMX,Master/Slave and Sound Active.

◇Great built-in shows under master/slave triggered by music.

◇Gobo wheel: 6 rotating gobos plus open

◇Color wheel: 8 colors plus white

◇14° beam angle

◇0%-100% smooth dimming snd various strobe effects

Power Voltage:AC 100~240V, 50/60Hz

Power Consumption: 70W

Light Source: 1 x 32W high brightness LED

Beam Angle: 14°

Weight: 5.3Kgs

Dimension: 212 x 174 x 352mm

3. How To Set The Unit

3.1 Fixture Overview

1. LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

2. Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

3. LED Display:

Used to show the various menus and the selected functions.

4. DMX IN/OUT:

For DMX512 links, use 3-pin XLR plug cable to link the unit together.

5. Only For Remote Control:

Used to connect with optional CA-8 to control the fixture for Stand by, Function and Mode

select.

6. Fuse:

Used to protect the fixture from damage of over current.

7. Mains In/Out:

Connect to supply mains power and the next unit.

3.2 Gobo Wheel

Rotation gobo wheel

3.3 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTER button and the display will blink. Use DOWN

and UP button to change the mode. Once the required mode has been selected, Press ENTER

button to store. Back to the main functions without any change press the MENU button or wait for

8 seconds.

Hold MENU button to quit menu mode, the unit will run the built-in program you selected.

The main functions are shown below:

DANGER!

Install/change the gobo-wheel with the device switched off only.

FIXTURE HOURS

SOFTWARE VERSION

LED DISPLAY OFF

LED DISPLAY ON

DISPLAY INVERSION

NORMAL

SLAVE MODE

BLACKOUT MODE

SOUND MODE

TEST

SOUND SENSE

RESET

NORMAL

PAN INVERSION

NORMAL

TILT INVERSION

TEMPERATURE

DMX 512 ADDRESS

To select the , press the ENTER button to show the DMX ADDRESS on the display. Use the

DOWN/UP button to adjust the address from 1to 512. Once the address has been selected, press

the ENTER button to setup, to go back to the functions without any changes press the MENU

button again. Hold and press the MENU button for one second or wait for one minute to exit the

menu mode.

CHANNEL MODE

To select the , press the ENTER button to show the DMX CHANNEL MODE on the display.

Use the DOWN/UP button to select the 8 CH or 10 CH mode. Once the mode has been selected,

press the ENTER button to setup, to go back to the functions without any changes press the MENU

button again. Hold and press the MENU button for one second or wait for one minute to exit the

menu mode.

SHOW MODE

To select the , press the ENTER button to show the SHOW MODE on the display. Use the

DOWN/UP button to select the (Show 1), (Show 2), (Show 3) or

(Show 4) mode.Once the show mode has been selected, press the ENTER button to setup, to go

back to the functions without any changes press the MENU button again. Hold and press the

MENU button for one second or wait for one minute to exit the menu mode.

SLAVE MODE

To select the , press the ENTER button to show the SLAVE MODE on the display. Use the

DOWN/UP button to select the (normal), (2 light show) mode.Once the mode has

been selected, press the ENTER button to setup, to go back to the functions without any changes

press the MENU button again. Hold and press the MENU button for one second or wait for one

minute to exit the menu mode.

DIMMER MODE

To select , press the ENTER button to show DIMMER MODE on the display. Use the

DOWN/UP buttons to select the (Dimmer 1), (Dimmer2), (Dimmer 3) or

(Dimmer 4) mode.Once the show has been selected, press the ENTER button to setup. To

go back to the functions without any changes press the MENU button again. Press and hold the

MENU button for about one second or wait for 7 seconds to exit the menu mode.

DIMMER SPEED

To select , press the ENTER button to show DIMMER SPEED on the display. Use the

DOWN/UP buttons to select the (Smooth) or (Fast)mode.Once the show has

been selected, press the ENTER button to setup. To go back to the functions without any changes

press the MENU button again. Press and hold the MENU button for about one second or wait for 7

seconds to exit the menu mode.

SOUND MODE

To select the , press the ENTER button to show the SOUND MODE on the display. Use the

DOWN/UP button to select the (sound mode on) or (sound mode off). Once the

mode has been selected, press the ENTER button to setup, to go back to the functions without any

changes press the MENU button again. Hold and press the MENU button for one second or wait

for one minute to exit the menu mode.

SOUND SENSE

To select the , press the ENTER button to show the SOUND SENSE on the display. Use the

DOWN/UP button to adjust the sound sensitivity from 0to 100. Once selected, press the ENTER

button to setup, to go back to the functions without any changes press the MENU button again.

Hold and press the MENU button for one second or wait for one minute to exit the menu mode.

Table des matières

Autres manuels ACME Matériel de DJ

ACME

ACME PAGEANT 300ZR Manuel utilisateur

ACME

ACME LED-245 II Manuel utilisateur

ACME

ACME 04XOZONE Manuel utilisateur

ACME

ACME CP-56U Manuel utilisateur

ACME

ACME CYC-200 FC Manuel utilisateur

ACME

ACME LED-256D RGB Manuel utilisateur

ACME

ACME Dotline360 TB-1230 QW Manuel utilisateur

ACME

ACME E-200 MB MC Manuel utilisateur

ACME

ACME MP-400Z IP Manuel utilisateur

ACME

ACME GLORY PROFILE Manuel utilisateur

ACME

ACME MINI ELLIPSOIDAL 10 Manuel utilisateur

ACME

ACME SAMBA Color Manuel utilisateur

ACME

ACME LED-MTX36 HEX Manuel utilisateur

ACME

ACME LED-RC8 Manuel utilisateur

ACME

ACME E-10T WW DXX Manuel utilisateur

ACME

ACME Ellipsoidal E-300 D2550 Manuel utilisateur

ACME

ACME LED-635S Manuel utilisateur

ACME

ACME AE-610 BEAM Manuel utilisateur

ACME

ACME Dotline 360 Manuel utilisateur

ACME

ACME LED-737 Manuel utilisateur

ACME

ACME PAGEANT 300ZR II Manuel utilisateur

ACME

ACME LED-920D Manuel utilisateur

ACME

ACME MH-640S-ELC Manuel utilisateur

ACME

ACME Solaris CM-S6 Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur