Abit SG-80DC Manuel utilisateur
Introduction
Hardware Setup BIOS Setup Driver & Utility Appendix
SG-80DC
Motherboard
Intel Pentium 4
Socket 775
Installation Instruction
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not represent a
commitment on part of the vendor, who assumes no liability or responsibility for any errors that may
appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the quality,
accuracy or fitness for any particular part of this document. In no event shall the manufacturer be
liable for direct, indirect, special, incidental or consequential damages arising from any defect or
error in this manual or product.
Product names appearing in this manual are for identification purpose only and trademarks and
product names or brand names appearing in this document are the property of their respective
owners.
This document contains materials protected under International Copyright Laws. All rights reserved.
No part of this manual may be reproduced, transmitted or transcribed without the expressed written
permission of the manufacturer and authors of this manual.
If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail,
we cannot guarantee any responsibility.
ii SG-80DC
Introduction
Contents
1. Introduction..................................................................... 1-1
Hardware Setup BIOS Setup Driver & Utility
Appendix
1.1 Features & Specifications .............................................................1-1
1.2 Motherboard Layout.....................................................................1-3
2. Hardware Setup ............................................................... 2-1
2.1 Choosing a Computer Chassis.......................................................2-1
2.2 Installing Motherboard .................................................................2-1
2.3 Checking Jumper Settings ............................................................2-2
2.3.1 CMOS Memory Clearing Header and Backup Battery ..............2-3
2.4 Connecting Chassis Components...................................................2-5
2.4.1 ATX Power Connectors ........................................................2-5
2.4.2 FAN Power Connectors ........................................................2-5
2.4.3 Front Panel Switches & Indicators Headers............................2-6
2.5 Installing Hardware......................................................................2-7
2.5.1 CPU Socket 775 ..................................................................2-7
2.5.2 DDR Memory Slots ............................................................2-10
2.5.3 Floppy and IDE Disk Drive Connectors ................................ 2-11
2.5.4 Serial ATA Connectors .......................................................2-12
2.5.5 Accelerated Graphics Port Slot............................................2-13
2.5.6 PCI Add-on Slots ...............................................................2-13
2.6 Connecting Optional Devices ......................................................2-14
2.6.1 Additional USB 2.0 Port Headers.........................................2-14
2.6.2 Internal Audio Source Connector ........................................2-14
2.6.3 Front Panel Audio Connection Header ................................. 2-15
2.7 Connecting I/O Devices..............................................................2-16
SG-80DC iii
3. BIOS Setup....................................................................... 3-1
4. Driver & Utility ................................................................. 4-1
5. Appendix .......................................................................... 5-1
5.1 Troubleshooting (How to Get Technical Support?)..........................5-1
5.1.1 Q & A.................................................................................5-1
5.1.2 Technical Support Form ......................................................5-3
iv SG-80DC
Introduction
1. Introduction
1.1 Features & Specifications
CPU
• LGA775 Socket for Intel®Pentium D/ Pentium 4/ Celeron Processors with 800/533
MHz FSB
• Compatible with Intel®P4-05A processors
• Supports Intel®Hyper-Threading / XD-bit / EM64T Technology
Chipset
• Northbridge: SIS 661FX
• Southbridge: SIS 964
Memory
• Two 184-pin DIMM slots
• Supports DDR 400 Un-buffered Non-ECC memory
• Supports maximum memory capacity up to 2GB
Graphics
• Integrated SIS Mirage Graphics GPU high performance 256-bit 3D engine and 2D
Accelerator
Serial ATA
• 2x SATA 1.5Gb/s Supports SATA RAID 0, RAID 1
LAN
• Onboard 10/100M PHY
Audio
• Onboard 5.1 channels Audio CODEC
Expansion Slots
• 1x AGP 8X slot
• 3x PCI slots
Internal I/O Connectors
• 1x Floppy port
• 1x UDMA 133/100/66/33 connector
• 2x SATA 1.5Gb/s connectors
• 2x USB 2.0 headers
• 1x AUDIO1 header
• 1x CD_IN header
Rear Panel I/O
• 1x PS/2 Mouse connector
SG-80DC 1-1
• 1x PS/2 Keyboard connector
• 1x Serial Port
• 1x Parallel Port
• 1x VGA connector
• 4x USB 2.0 connectors
• 1x RJ-45 LAN Connector
• 1x Audio connector (Line-out, Line-in, MIC-in)
Miscellaneous
• ATX form factor (244mm x 244mm)
※ Specifications and information contained herein are subject to change without
notice.
1-2 SG-80DC
Introduction
1.2 Motherboard Layout
SG-80DC 1-3
1-4 SG-80DC
Hardware Setup
SG-80DC 2-1
2. Hardware Setup
In this chapter we will elaborate all the information you need upon installing this motherboard
to your computer system.
※ Always power off the computer and unplug the AC power cord before adding or
removing any peripheral or component. Failing to so may cause severe damage
to your motherboard and/or peripherals. Plug in the AC power cord only after
you have carefully checked everything.
2.1 Choosing a Computer Chassis
• This motherboard carries an mATX form factor of 244 x 244 mm. Choose a chassis big
enough to install this motherboard.
• As some features for this motherboard are implemented by cabling connectors on the
motherboard to indicators and switches or buttons on the chassis, make sure your chassis
supports all the features required.
• If there is possibility of adopting some more hard drives, make sure your chassis has
sufficient power and space for them.
• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O
shield of the chassis matches the I/O port configuration of this motherboard. You can find
an I/O shield specifically designed for this motherboard in its package.
2.2 Installing Motherboard
Most computer chassis have a base with
many mounting holes to allow the
motherboard to be securely attached, and at
the same time, prevent the system from
short circuits. There are two ways to attach
the motherboard to the chassis base:
1. use studs, or
2. use spacers
In principle, the best way to attach the board
is to use studs. Only if you are unable to do
this should you attach the board with spacers.
Line up the holes on the board with the mounting holes on the chassis. If the holes line up and
there are screw holes, you can attach the board with studs. If the holes line up and there are
only slots, you can only attach with spacers. Take the tip of the spacers and insert them into
the slots. After doing this to all the slots, you can slide the board into position aligned with slots.
After the board has been positioned, check to make sure everything is OK before putting the
chassis back on.
To install this motherboard:
1. Locate all the screw holes on
the motherboard and the
chassis base.
2. Place all the studs or spacers
needed on the chassis base
and have them tightened.
3. Face the motherboard’s I/O
ports toward the chassis’s rear
panel.
4. Line up all the motherboard’s
screw holes with those studs o
r
spacers on the chassis.
5. Install the motherboard with
screws and have them
tightened.
Face the chassis’s rear panel.
※ To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if
they are already fastened on the chassis base and are without mounting-holes
on the motherboard to align with.
2.3 Checking Jumper Settings
For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the
jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position.
SHORT OPEN OPEN
For 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in.
Pin 1~2 SHORT Pin 2~3 SHORT
2-2 SG-80DC
Table des matières
Autres manuels Abit Carte mère
Abit
Abit VH6 Manuel utilisateur
Abit
Abit NF-M2 NVIEW Manuel utilisateur
Abit
Abit BD7 Manuel utilisateur
Abit
Abit BG7E Manuel utilisateur
Abit
Abit IX48 GT3 Manuel utilisateur
Abit
Abit IL8 Manuel utilisateur
Abit
Abit IB9 Manuel utilisateur
Abit
Abit KT7 Manuel utilisateur
Abit
Abit TH7II-RAID Manuel utilisateur
Abit
Abit Socket 462 System Board Manuel utilisateur
Abit
Abit AI7 Manuel utilisateur
Abit
Abit PX5 Manuel utilisateur
Abit
Abit IC7-MAX3 Manuel utilisateur
Abit
Abit SA6 Manuel utilisateur
Abit
Abit BX 133 Manuel utilisateur
Abit
Abit KT7 Manuel utilisateur
Abit
Abit SR7-8X Manuel utilisateur
Abit
Abit NF8 Pro Manuel utilisateur
Abit
Abit A-N68SV Series Manuel utilisateur
Abit
Abit KV7-V Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
