ABB RTAC-01 Manuel utilisateur

ABB Drives

Pulse Encoder Interface Module

RTAC-01

User’s Manual

Pulse Encoder Interface Module

RTAC-01

User’s Manual

3AFE 64486853 REV A EN

EFFECTIVE: 1.5.2002

RTAC-01 User’s manual iii

Safety instructions

Overview This chapter states the general safety instructions that

must be followed when installing and operating the

RAIO-01 Analogue I/O Extension module.

The material in this chapter must be studied before

attempting any work on, or with, the unit.

In addition to the safety instructions given below, read

the complete safety instructions of the specific drive you

are working on.

General safety

instructions

WARNING! All electrical installation and maintenance

work on the drive should be carried out by qualified

electricians only.

The drive and adjoining equipment must be properly

earthed.

Do not attempt any work on a powered drive. After

switching off the mains, always allow the intermediate

circuit capacitors 5 minutes to discharge before working

on the frequency converter, the motor or the motor

cable. It is good practice to check (with a voltage

indicating instrument) that the drive is in fact discharged

before beginning work.

The motor cable terminals of the drive are at a

dangerously high voltage when mains power is applied,

regardless of motor operation.

There can be dangerous voltages inside the drive from

external control circuits even when the drive mains

power is shut off. Exercise appropriate care when

working on the unit. Neglecting these instructions can

cause physical injury or death.

Safety instructions

iv RTAC-01 User’s manual

RTAC-01 User’s manual v

Table of contents

Safety instructions

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

General safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Table of contents

Chapter 1 – Introduction

Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

What this manual contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Chapter 2 – Overview

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

The RTAC-01 module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Module layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Delivery check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Warranty and liability information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Chapter 3 – Installation

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Terminal designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Encoder wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Phasing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Encoder output types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Node address selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

Table of contents

vi RTAC-01 User’s manual

Chapter 4 – Fault tracing

Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Option slot installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

I/O Module Adapter installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Appendix A – Technical data

RTAC-01 User’s manual 1-1

Chapter 1 – Introduction

Intended

audience

The manual is intended for the people who are

responsible for commissioning and using an RTAC-01

Pulse Encoder Interface module with the ACS 800

drive. The reader is expected to have a basic

knowledge of electrical fundamentals, electrical wiring

practices and how to operate the drive.

Before you start It is assumed that the drive is installed and ready to

operate before starting the installation of the extension

module.

In addition to conventional installation tools, have the

drive manuals available during the installation as they

contain important information not included in this

manual. The drive manuals are referred to at various

points of this document.

Chapter 1 – Introduction

1-2 RTAC-01 User’s manual

What this manual

contains

This manual contains information on the wiring,

configuration and use of the RTAC-01 module.

Safety instructions are featured in the first few pages

of this manual.

Chapter 2 – Overview contains a short description of

the RTAC-01 Pulse Encoder Interface module, a

delivery checklist and warranty information.

Chapter 3 – Installation contains instructions for

module hardware settings, mounting and cabling.

Chapter 4 – Fault tracing explains fault tracing and

the LED indications of the RTAC-01 module.

Appendix A contains technical data.

Table des matières

Autres manuels ABB Unité de contrôle

ABB

ABB ACS850 series Manuel utilisateur

ABB

ABB RELION 650 SERIES Guide de démarrage rapide

ABB

ABB RELION Series Manuel utilisateur

ABB

ABB Triguard SC300E Manuel utilisateur

ABB

ABB WaveLINE 6731-21-500 Manuel utilisateur

ABB

ABB Relion 615 series Manuel utilisateur

ABB

ABB ACH580-04 Manuel utilisateur

ABB

ABB Arc Guard System TVOC-2 Manuel du produit

ABB

ABB 07 MK 92 R1161 Manuel utilisateur

ABB

ABB RED615 ANSI Manuel utilisateur

ABB

ABB Powernet 6920U-102-500 Manuel utilisateur

ABB

ABB IEC 61850 Edition 2 Manuel utilisateur

ABB

ABB ret650 Guide de démarrage rapide

ABB

ABB ACS880-1604LC Manuel utilisateur

ABB

ABB A3 Series Manuel utilisateur

ABB

ABB Welcome M2306 Manuel utilisateur

ABB

ABB ACQ580-34 Manuel utilisateur

ABB

ABB RET615 Manuel utilisateur

ABB

ABB FSE-31 Manuel utilisateur

ABB

ABB NMBP-01 Manuel d'installation

ABB

ABB UCU-22 Manuel utilisateur

ABB

ABB MicroFlex e150 Manuel utilisateur

ABB

ABB RER 103 Instructions d'utilisation et d'installation

ABB

ABB REF542plus Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur