ABB FCAN-01 Manuel d'installation

Options for ABB drives, converters and inverters

Quick installation and start-up guide

FCAN-01 CANopen adapter module

Safety instructions

WARNING! Obey the safety instructions. If you ignore them, injury or death, or damage to the

equipment can occur. See the user’s manual.

Mechanical installation

Electrical installation

Layout of the module

1. Pull out the lock.

2. Install the module carefully to an option

module slot of the drive. See the drive

hardware manual.

3. Push in the lock.

4. Tighten the screw to torque 0.8 N·m using

a Torx TX10 screwdriver.

WARNING! Do not use excessive force,

or leave the screw too loose. Over-

tightening can damage the screw or

module. A loose screw decreases the EMC

performance, and can even cause an operation

failure.

No. Description

1Lock

2 Mounting and grounding screw

3 Bus connector [X1]

4 Diagnostic LEDs

Start-up

When the module is connected to the drive, the drive control program sets the applicable parameters.

See the appropriate drive manual.

Basic parameter settings

To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par refresh.

Further information

Index Name Value

20.01 Ext1 commands Fieldbus A

22.11 Speed ref1 source FBA A ref 1

28.11 Frequency ref1 source FBA A ref 1

50.01 FBA A enable Enable (or select the option slot in which the module is installed)

50.02 FBA A comm loss func Fault

51.02 Node ID Set the node address of the device.

51.03 Bitrate Set the bit rate for the CANopen interface.

51.05 Profile The ABB Drives communication profile is the default value.

See the latest version of FCAN-01 CANopen adapter

module user's manual (3AFE68615500 [English]) in ABB

library (www.abb.com/drives/documents).

For more information on fieldbus options and protocols

provided by ABB Drives, see the fieldbus

communications web page

(new.abb.com/drives/connectivity/fieldbus-connectivity).

Pin allocation for [X1] Bus termination

Bus termination is required to prevent signal reflections

from the bus cable ends. The module is not equipped with

internal bus termination. Therefore, the first and last

nodes of the bus must be included with bus termination.

In the this diagram, the built-on terminations of the D-SUB

connectors at the first and last nodes are switched on.

According to CANopen specification CiA 301.

Pin Description

1 - Not in use

2 CAN_L CAN_L bus line

3 CAN_GND CAN ground

4 - Not in use

5 CAN_SHLD Optional CAN shield

6 GND Optional ground

7 CAN_H CAN_H bus line

8 - Not in use

9 CAN_V+ Not supported.

SUB-D9

(male)

CANopen

CANopen CANopenCANopen

OFF

OFF ON

3AXD50000158195 Rev A (EN) 2017-11-23

FCAN-01 manual

Fieldbus communications web page

Autres manuels pour FCAN-01

Table des matières

Autres manuels ABB Unité de contrôle

ABB

ABB RELION 650 SERIES Manuel utilisateur

ABB

ABB AC500 PLC Manuel utilisateur

ABB

ABB SAS-W1.1E Guide de l'utilisateur

ABB

ABB Arc Guard System TVOC-2 Manuel du produit

ABB

ABB RDCO-01 Manuel utilisateur

ABB

ABB LD 800HSE Manuel utilisateur

ABB

ABB TA571-SIM Manuel utilisateur

ABB

ABB ACS800-U4 Manuel utilisateur

ABB

ABB NMBA-01 Manuel d'installation

ABB

ABB i-bus EIB Manuel utilisateur

ABB

ABB Welcome M2306 Manuel utilisateur

ABB

ABB RELION 650 SERIES Fiche technique

ABB

ABB FSPS-21 Manuel utilisateur

ABB

ABB ACS880-304 +A003 Series Manuel utilisateur

ABB

ABB Relion 670 series Instructions d'utilisation

ABB

ABB MTQ22-FBP.0 Manuel utilisateur

ABB

ABB SACE PR212/D-L Manuel utilisateur

ABB

ABB TruONE Ekip Manuel utilisateur

ABB

ABB 615 Series ANSI Manuel utilisateur

ABB

ABB Foundation LD 810HSE Ex Manuel utilisateur

ABB

ABB FOX61 Series Manuel utilisateur

ABB

ABB FDNA-01 Manuel d'installation

ABB

ABB FAIO-01 Manuel utilisateur

ABB

ABB Welcome M2306 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur