3D Systems Cubify CUBEX Duo Manuel utilisateur

CUBEX

Measuring

Stepper motor

chip voltages

Contents

What you will need ..................................................................................................... 3

Removing the Jet Wipe .............................................................................................. 4

Removing the Case and floor panel. .......................................................................... 4

Voltage Measurement Locations................................................................................ 6

Reading the Voltages................................................................................................. 7

Re attaching the floor panel and case........................................................................ 8

What you will need

Multimeter

3mm hex driver

Small Screwdriver

Before beginning this process please ensure that all cartridges have been

removed from the machine.

Removing the Jet Wipe

Run the bed to the bottom of the machine using manual move.

Lift Jet wipe out of the machine

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

Voltage Measurement Locations

Depending which stepper motor chip voltage you want to read, you will need to

position your multimeter in different positions of the board. You will need to place a

small screwdriver with one end of the multimeter clipped onto it on the small screw

head labelled TP – and another end of the multimeter will need to be set to ground

on the board.

TP X will measure the voltage for the X axis.

TP Y will measure the voltage for the Y axis.

TP Z will measure the voltage for the Z axis.

TP E1, TP E2 and TP E3 will measure the voltage for print jets 1, 2 and 3.

TP Z

TP Y

TP X

Ground

Reading the Voltages

Plug the CubeX into mains power

Set the multimeter to read DC voltage.

Place the Red (positive) lead onto the desired TP screwhead.

TP E1

TP E2

TP E3

Hold the other end of the multimeter against the ground point.

The multimeter screen will give you your voltage reading.

TP X should read 1.3VDC

TP Y should read 1.6VDC

TP Z should read 1.3VDC

TP E1, E2 and E3 should read 1.1VDC

If your voltage is not correct use the small screwdriver to turn the screwhead in very

small increments measuring the voltage between each turn until it is correct.

Unplug your CubeX from mains power.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

You may now power up your CubeX.

Autres manuels pour Cubify CUBEX Duo

Table des matières

Autres manuels 3D Systems Imprimante 3D

3D Systems

3D Systems ZPRINTER 650 Manuel utilisateur

3D Systems

3D Systems ProX 800 Manuel utilisateur

3D Systems

3D Systems CubeX Manuel utilisateur

3D Systems

3D Systems Cube 3rd Generation Manuel utilisateur

3D Systems

3D Systems ProJet 4500 Manuel utilisateur

3D Systems

3D Systems Duraform ProX PA Manuel utilisateur

3D Systems

3D Systems ProX SLS 6100 Manuel utilisateur

3D Systems

3D Systems ProJet 2500 Manuel utilisateur

3D Systems

3D Systems wematter Atmosphere Manuel utilisateur

3D Systems

3D Systems CubePro Manuel utilisateur

3D Systems

3D Systems Figure 4 Standalone Manuel

3D Systems

3D Systems CUBE Manuel utilisateur

3D Systems

3D Systems CubePro Instructions d'utilisation

3D Systems

3D Systems ProX 500 Manuel utilisateur

3D Systems

3D Systems CubePro Manuel utilisateur

3D Systems

3D Systems CubeX Instructions de montage

3D Systems

3D Systems Figure 4 Standalone Manuel utilisateur

3D Systems

3D Systems ProJet 1200 Manuel utilisateur

3D Systems

3D Systems ProJet 1200 Manuel utilisateur

3D Systems

3D Systems ProJet 4500 Manuel utilisateur

3D Systems

3D Systems ProX 950 Manuel utilisateur

3D Systems

3D Systems ProX DMP 300 Manuel utilisateur

3D Systems

3D Systems CubePro Manuel utilisateur

3D Systems

3D Systems ProX DMP320 Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur