ZyXEL Communications P-871M Manuel utilisateur

P-871M

VDSL Modem

User’s Guide

Version ME1

5/2008

Edition 1

DEFAULT LOGIN

Password 1234

Console Port Speed 38400 bps

P-871M User’s Guide

Overview

The P-871M is a VDSL modem in CPE (Customer Premises

Equipment) mode and can also act as CO (Central Office)

equipment. CO equipment is where home and office phone

lines terminate and connects to a much larger switching

system. In the following example, you can build up a VDSL

bridge connection between two P-871Ms.

This guide covers:

•Overview, page 2

•Hardware Connections, page 3

•CLI Commands Configuration, page 6

•Firmware Upgrade, page 9

•Wall-mounting Instructions, page 12

P-871M User’s Guide

1 Hardware Connections

You can set the P-871M to work in either CO mode or CPE

mode. Follow the procedure below to complete the hardware

connections.

1.1 CO Mode

1Set the CO/CPE switch on the rear panel to the CO side.

2Use the included console cable to connect the CONSOLE

port to your computer’s COM port for configuration.

3Use the included yellow Ethernet cable to connect the

ETHERNET port to your network device, such as a switch.

4Over ISDN: Use the included gray cable with a RJ-45

connector to connect the DSL port to another P-871M in

CPE mode.

Over POTS: Use the included gray cable with a RJ-11

connector to connect the DSL port to another P-871M in

CPE mode.

CPE

P-871M User’s Guide

5Use the included power adaptor to connect the POWER

socket to a proper power source.

6Push the power switch to the on position.

1.2 CPE Mode

1Set the CO/CPE switch on the rear panel to the CPE side.

2Use the included console cable to connect the CONSOLE

port to your computer’s COM port for configuration.

3Use the included yellow Ethernet cable to connect the

ETHERNET port to your network device, such as a switch.

4Over ISDN: Use the included gray cable with a RJ-45

connector to connect the DSL port to another P-871M in

CO mode.

Over POTS: Use the included gray cable with a RJ-11

connector to connect the DSL port to another P-871M in

CO mode.

5Use the included power adaptor to connect the POWER

socket to a proper power source.

CPE

P-871M User’s Guide

6Push the power switch to the on position.

1.3 LEDs (Lights)

Look at the LEDs on the top panel of the P-871M.

•ThePOWER LED is on when the system is ready.

•TheETHERNET LED turns on if the ETHERNET port is con-

nected to an Ethernet device and blinks when the P-871M is

sending or receiving data through the ETHERNET port.

•TheDSL LED is on if the VDSL connection between two P-

871Ms is set up.

•TheCO LED is on when the P-871M is operating in CO

mode.

VIf none of the LEDs (lights) are on, check your

connections. Make sure that you have the

power adaptor connected to the P-871M and

plugged in to an appropriate power source.

Make sure the power source is turned on. Turn

the P-871M off, wait for a few seconds and turn

it back on. If the LEDs are still off, contact your

vendor.

P-871M User’s Guide

2 CLI Commands Configuration

When the P-871M is in CO mode, use the CLI (Command

Line Interface) commands to configure it.

2.1 Syntax Conventions

This manual follows these general conventions:

• Units of measurement may denote the “metric” value or the

“scientific” value. For example, “k” for kilo may denote “1000”

or “1024”, “M” for mega may denote “1000000” or “1048576”

and so on.

Command descriptions follow these conventions:

• Commands are in courier new font.

• Required input values are in angle brackets <>; for example,

ping <ip-address>means that you must specify an IP

address for this command.

• Optional fields are in square brackets []; for instance vdsl

profile [1|2], the name field is optional.

•The|(bar) symbol means “or”.

•italic terms represent user-defined input values; for

example, in vdsl downrate [y], ycan be replaced by the

actual data rate that you want to set, for example, 10000.

• A key stroke is denoted by square brackets and uppercase

text, for example, [ENTER] means the “Enter” or “Return”

key on your keyboard.

P-871M User’s Guide

2.2 Accessing the CLI

1Connect your computer to the console port and use

terminal emulation software configured to the following

parameters:

• VT100 terminal emulation

• 38400 bps

• No parity, 8 data bits, 1 stop bit

• No flow control

2Press [ENTER] to open the login screen.

3Enter the system login password.

"The default system password is 1234.

2.3 Commands Summary

The following table lists the commands available on the P-

871M.

"Use the ?or help command to see the

available commands.

P-871M User’s Guide

Command Description

sys Displays the system information and port

settings, including the current firmware version

and VDSL data rate.

lt=line termination, means CO mode;

nt=network termination, means CPE mode

help Displays all available commands.

exit Logs you out of the CLI.

passwd Changes the system login password.

default Returns the P-871M to the factory defaults.

upgrade

<fw|conf>

Uploads the P-871M’s firmware or

configuration file.

vdsl uprate [x]Displays or sets the VDSL upstream data rate.

x: Enter the rate from 2000 to 100000 in Kbps.

vdsl downrate

[y]

Displays or sets the VDSL downstream data

rate.

y: Enter the rate from 2000 to 100000 in Kbps.

vdsl snr [z]Displays or sets the VDSL SNR margin.

z: Enter the SNR margin from 0 to 24 in dB.

vdsl interleave

[i]

Displays or sets the VDSL interleave delay.

i: Enter the interleave delay from 0 to 100 in

0.5 ms (milisecond).

vdsl profile

[1|2]

Displays or sets the VDSL profile.

1: 12a, PSD:998-M1x-B

2: 12a, PSD:997-M1x-M

vdsl reset Resets the VDSL chipset.

vdsl reconnect Forces the P-871M to re-build up the VDSL

connection.

P-871M User’s Guide

3 Firmware Upgrade

This section shows you how to upload firmware via the

console port.

vdsl debug Displays VDSL debugging information.

vdsl show Displays the VDSL status and performance

data.

vdsl active

[on|off]

Displays the VDSL port status or enables/

disables the VDSL port.

enet auto

[on|off]

Displays or sets auto-negotiation mode.

enet speed

[10|100]

Displays or sets the Ethernet port speed (10 or

100 Mbps).

enet duplex

[full|half]

Displays or sets the Ethernet duplex mode.

enet fctrl

[on|off]

Displays or sets flow control.

enet status Displays the Ethernet port statistics.

enet clear Removes the Ethernet port statistics.

Command Description

P-871M User’s Guide

1Do not interrupt the file transfer

process as this may PERMANENTLY

DAMAGE your P-871M.

1Obtain the firmware file, unzip it and save it in a folder on

your computer.

1Only upload firmware for your specific

model!

2Access the CLI and type the upgrade fw command.

3Type yand press [ENTER].

4When you see the Press any key to start

message,press a key and activate XMODEM upload on

your terminal.

Autres manuels pour P-871M

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ZyXEL Communications Modem

ZyXEL Communications

ZyXEL Communications NBG-419N Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 971M Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 841 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Comet 3356 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 630 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 600 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Comet 336P Manuel utilisateur

ZyXEL Communications

ZyXEL Communications PMG1005-T20B Manuel utilisateur

ZyXEL Communications

ZyXEL Communications P-971M Manuel utilisateur

ZyXEL Communications

ZyXEL Communications U-336S Manuel utilisateur

ZyXEL Communications

ZyXEL Communications VMG3006-D70A Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-220 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Prestige 630 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications P-630-S Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications MAX-100 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications U-1496 series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications P-660R-T1 Manuel

ZyXEL Communications

ZyXEL Communications Prestige 971M Manuel utilisateur

ZyXEL Communications

ZyXEL Communications XMG5101-S10A Manuel utilisateur

ZyXEL Communications

ZyXEL Communications P-870M-I1 V2 Guide de référence

ZyXEL Communications

ZyXEL Communications PRESTIGE 871 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Omni TA128 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ADSL-Modem Manuel utilisateur

ZyXEL Communications

ZyXEL Communications Omni 56K Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur