Zephyr AIN-M80AWX Guide de démarrage rapide

www.zephyronline.com

Wave

AWA-M90AWX

AWA-M90ABX

Incline

AIN-M80AWX

AIN-M80ASX

RANGE HOOD - Installation and use instructions

ENGLISH........................................3

FRANÇAIS...................................33

- 6 -

LIST OF MATERIALS

Incline

- Zephyr blower sold separately

- Non-ducted recirculating kit sold separately

- Duct cover accessory sold separately

Box Cover (box

marked “120 VAC

Input”)

Box marked “120

VAC Input”

Led

Mesh Filter

Hardware Packet

Remote Blower Collar with

Damper (External motor)

Remote Blower Box Cover

Remote Blower Box

Electrical System Box

Remote Blower Wiring Extension

Remote Blower Wiring Harness

- 7 -

LIST OF MATERIALS

Wave

- Zephyr blower sold separately

- Non-ducted recirculating kit sold separately

- Duct cover accessory sold separately

Box Cover (box

marked “120 VAC

Input”)

Box marked “120

VAC Input”

Led

Mesh Filter

Hardware Packet

Remote Blower Collar with

Damper (External motor)

Remote Blower Box Cover

Remote Blower Box

Electrical System Box

Remote Blower Wiring Extension

Remote Blower Wiring Harness

- 8 -

DUCTING CALCULATION SHEET

Maximum Duct Length:

For satisfactory air movement, the total duct length

should not exceed 100 equivalent feet.

- 9 -

HOOD SPECIFICATIONS

Incline

- 10 -

HOOD SPECIFICATIONS

Wave

- 11 -

WIRING DIAGRAM

- 16 -

INSTALLING THE DUCTWORK:

INTERNAL BLOWER

NOTE: To reduce the risk of fire, use only

metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

2. A straight, short duct run using a minimum

6” round duct will allow the hood to perform

most efficiently.

3. Long duct runs, elbows, and transitions will

reduce the performance of the hood. Use

as few of them as possible.

4. Install a roof or wall cap. Connect round

metal ductwork to cap and work back

towardshoodlocation.Useducttapetoseal

the joints between ductwork sections

(Fig.7). FIG. 7

ROOF CAP

OPTIONAL

DUCT COVER

HOOD

22” MINIMUM ABOVE COOKING

SURFACE

WALL

CAP

6” ROUND DUCT

FIG. 8

FIG. 9

Model Incline

Model Wave

FIG.10

Model Wave

PREPARE FOR INSTALLATION

ModelIncline

Remove the (2) screws and take off the front

panel. See Fig. 8.

Model Wave

1. Open the upper front glass; remove the

lower glass unscrewing (2) screws and

moving it upward (Fig.9).

2. Remove the metal panel unscrewing (6)

screws. Fig. 10.

- 17 -

INSTALLATION INTERNAL

BLOWER

NOTE: The following instructions are for

installingtheinternalblower only.

Installthisrangehoodonlywithinternalblower

model CBI-290A or CBI-600A.

1. Remove the knockout (B). Fig. 13.

2. Fix the internal blower with (4) mounting

screws (supplied with the internal blower).

Fig. 13.

(4) MOUNTING SCREWS

(Supplied with the motor)

CHOOSE AIR OUTLET

LOCATION

The hood is supplied with upper air outlet;

but you can let the air out the back, turning

the motor plate.

Rotation of the motor plate:

1.Remove the motor plate unscrewing (6)

screws (Fig.11).

2.Rotate the motor plate and re-fix in the new

position (Fig.12).

In the installation with internal blower, use

the rond knockout (B);

in the installation with remote or In-line

blower, use the other knockout (A).

FIG.11

FIG.12

FIG.13

KNOCKOUT

(B) KNOCKOUT

(A)

KNOCKOUT

(B)

- 18 -

REMOTE BLOWERS (EXTERNAL AND IN-LINE)

CAUTION: To reduce risk of fire and electric shock, install this range hood only with External

Blower Model CBE-1000, and In-Line Blower Model PBN-1000A. Other blowers cannot be

substituited.

INSTALLING THE DUCTWORK: REMOTE BLOWER

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the External Blower or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run using a minimum 8” round duct will allow the hood to perform

most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as

few of them as possible. Larger ducting may be required for best performance with long

duct runs.

4. After the Exterior or In-Line Blower has been installed, connect round metal ductwork

and work back towards the hood location. Use duct tape to seal joints between ductwork

sections.

Roof Pitch w/

Flashing & Cap

in-line

blower

(blower

housing)

external blower

Attic or crawl space

(blower

housing)

Roof Pitch w/

Flashing & Cap

in-line

blower

(blower

housing)

external blower

Attic or

crawl

space

(blower

housing)

Autres manuels pour AIN-M80AWX

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Zephyr hotte de ventilation

Zephyr

Zephyr Verona ZVO-E30BG Guide d'installation

Zephyr

Zephyr AK9800 Guide d'installation

Zephyr

Zephyr Cypress AK7836BS Guide d'installation

Zephyr

Zephyr ZPY-E36AB Guide d'installation

Zephyr

Zephyr Cypress AK7848ASX Guide d'installation

Zephyr

Zephyr Monsoon DCBL AK9428AS Guide d'installation

Zephyr

Zephyr Ombra ZOM-E30ABS Guide d'installation

Zephyr

Zephyr Ombra Guide d'installation

Zephyr

Zephyr Siena ZSI-E30CS Manuel utilisateur

Zephyr

Zephyr ACT Roma Wall ZRO-E30CS Manuel utilisateur

Zephyr

Zephyr Siena Guide d'installation

Zephyr

Zephyr Venezia Guide d'installation

Zephyr

Zephyr Z1C01ML Guide d'installation

Zephyr

Zephyr LAYERS WALL DLA-E42ASSX Manuel utilisateur

Zephyr

Zephyr Edge Wall AED - M90ASX Manuel utilisateur

Zephyr

Zephyr Monsoon II AK9340AS Guide d'installation

Zephyr

Zephyr ZMD-M90BS Guide d'installation

Zephyr

Zephyr Monsoon I AK9240AS Guide d'installation

Zephyr

Zephyr Typhoon AK2100CS Guide d'installation

Zephyr

Zephyr Tornado Mini AK8400AS Guide d'installation

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Zephyr

Zephyr ARC AHZ-M90ABX Manuel utilisateur

Zephyr

Zephyr ATI-M90ASX Manuel utilisateur

Zephyr

Zephyr Typhoon AK2100BS Guide d'installation

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur

Nibe

Nibe S Series Guide de l'utilisateur