Zephyr AK0710 Guide d'installation

www.zephyronline.com

Use, Care and Installation Guide

Tempest I , II

Stainless Steel

Backsplash

AK0710 - 30”

AK0716 - 36”

AK0712 - 42”

AK0718 - 48”

FEB07.0201

Table of Contents

LIST OF MATERIALS —————————–- 2

SPECIFICATION ———————————— 3

INSTALLATION ————————————- 4,5

CLEANING AND

CONTACT INFORMATION ———————— 6

1

List of Materials

1 - Upper Section

1 - Lower Section

2 - Wire Racks

1 - Hardware Packet

2 - Retaining Clips

4 - Hinge Clips

6 - 7/16” Carriage Head Bolts

8 - 5/8” Philips Head Wood Screw

6 - Carriage Head Bolt Nuts

Note: If any parts are missing, please call

1-888-880-8368 for replacements.

2

Specifications

3

Installation

1. Mark a level line on the wall at 16” below bottom of hood.

2. Position the lower section of backsplash (flat part with flange on top) on the wall.

Center it side to side and mark the top and bottom holes. Remove the lower section from

the wall.

3. If installing onto drywall only and not onto studs, insert wall anchors (we recommend EZ

anchors) into the marked holes. If installing onto studs, attach screws without EZ anchors.

4. Attach lower section of backsplash to wall with screws provided.

5. Position upper section of backsplash by engaging its flange with the lower section. Push up

to fully engage flanges*, center it side to side and mark the location of the mounting holes.

Remove the upper section from drywall and install wall anchors into marked holes.

5b.If hood is already installed, attach wall anchors into the (3) holes from inside the hood at the

bottom. These are the holes which the upper section will line up with and mount to the wall.

6. Insert retaining clips and hinge clips to the upper section. The retaining clips go in the top

top two openings and the hinge clips go in the bottom four openings. (see diagram, page 4)

Fasten and tighten nuts to the clips on back of the upper section with the provided

hardware.

7. Attach upper section to wall with screws provided. If hood is already installed, Insert the top

2” lip of the upper section behind the bottom of the hood and line up the holes with the (3)

holes at the bottom of the hood. Insert screws into holes and fasten upper section to wall.

*note: in some installations, the flanges will not fully engage in the final install. This is fine

since the weight of the upper section will rest against the bottom section.

4

Installation

1. For the warming plate option; snap the wire shelves into hinge clips

on the backsplash as shown in the left side shelf diagram.

2. For the spice rack option; attach shelf to hinge clips, as

show in the right side shelf diagram, then rotate shelf upwards and

secure with retaining clip.

5

Cleaning and Contact Information

Cleaning of the backsplash should be done frequently to preserve the

life of the stainless steel. Cleaning should typically be done once or

twice a month depending on your cooking habits.

When cleaning, use a non abrasive cleaner, do not use “orange”

cleaner. Abrasive cleaners may scratch the surface and discolor the

stainless steel. To clean the wire racks, soak them in soapy water.

DO NOT place in a dishwasher as this may discolor the wire racks.

You may also polish the stainless steel by using stainless steel polish.

Make sure when polishing to go along with the grain of the backsplash.

Zephyr Corporation

395 Mendell Street

San Francisco, CA 94124

1-888-880-8368

6

Ce manuel convient aux modèles suivants

3

Table des matières

Autres manuels Zephyr hotte de ventilation

Zephyr

Zephyr ARC AHZ-M90AWX Manuel utilisateur

Zephyr

Zephyr ZTR-M90S Guide d'installation

Zephyr

Zephyr Luce Island ZLC-M90AS Guide d'installation

Zephyr

Zephyr elica Glide Guide d'installation

Zephyr

Zephyr Modena Wall ZMO-E30AS Guide d'installation

Zephyr

Zephyr Okeanito COK-E36BSX Guide d'installation

Zephyr

Zephyr ALU-E43 Guide de démarrage rapide

Zephyr

Zephyr HORIZON DHZ-M90AMWX Manuel utilisateur

Zephyr

Zephyr Typhoon AK2100 Guide d'installation

Zephyr

Zephyr Z1C-00VS Manuel utilisateur

Zephyr

Zephyr ZML-M90S/G Guide d'installation

Zephyr

Zephyr Monsoon II AK9340AS Guide d'installation

Zephyr

Zephyr Tempest II AK7536ASX Guide d'installation

Zephyr

Zephyr Bogart EBO-E42ASX Guide d'installation

Zephyr

Zephyr Roma Island ZRM-E36BS Guide d'installation

Zephyr

Zephyr AK9028AS Guide d'installation

Zephyr

Zephyr AK9028AS Guide d'installation

Zephyr

Zephyr Tidal I Guide d'installation

Zephyr

Zephyr Duo Wall ADU - M90ASX Manuel utilisateur

Zephyr

Zephyr Angolo ZAG-E30AG Guide d'installation

Zephyr

Zephyr Milano Wall ZMI-M90BS Guide d'installation

Zephyr

Zephyr ZPY-E30AS Guide d'installation

Zephyr

Zephyr Titan AK7636AS Guide d'installation

Zephyr

Zephyr ASL-E42ASX Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur

Nibe

Nibe S Series Guide de l'utilisateur