Zeiss opmi lumera 700 Guide d'installation
Lumera ®700
Basic Instructions
Attention: Refer to the User Manual for additional warnings, safety information, labeling and detailed operating instructions.
This basic instruction sheet is only a complement to the User manual (G-30-1673-en).
Switch the power on by pressing the on/off switch
This will be on the wall for a ceiling mounted microscope, or on the base unit for a floor mounted microscope.
Foot Pedal:
Once the microscope is booted up and showing the Main Menu, place the foot pedal horizontally flat on the floor in order to establish
a connection with the microscope. You should then see a symbol in the top right hand corner indicating the foot pedal is connected to
the microscope and the amount of power left in the battery.
The foot pedal should be hung up on the appropriate bar when not used to maintain battery power for a long as possible.
IF THE FOOT PEDAL POWER SHOULD FAIL, ATTACH TO THE MICROSCOPE USING THE CABLE PROVIDED.
Activate User Profile
The microscope will default to the last user profile used. Check it is the correct one for each surgeon.
To change to a different user, click on User in the main Menu, click the drop down box under User and select the user
required. Once selected click the Activate icon at the bottom. If you do not the microscope will default to the previous user
and their profile.
Refer to:
Version 8.1
Page 194
G-30-1673-en
Configure User Settings
Set Up Profile
In the User Menu, click on the paper with the + symbol to enter a Surgeon Name, then click save icon at the bottom.
Then on the Surgery Profile Icon, select Anterior or Posterior. Lastly click Activate icon at the bottom.
Only if using Posterior with RESIGHT, click on the configuration (spanner) icon, then click on Posterior profile icon and finally click on the “R” to
link the RESIGHT into the posterior profile. Click save icon at the bottom. Posterior profile will now activate whenever RESIGHT is positioned
under the microscope.
Light Settings
In the main menu, click on Light icon, then click OPMI light icon. The light intensity can then be adjusted on the left hand side with the up
and down arrow icons.
The Red Reflex to Full Field can also be adjusted on the horizontal bar using the left and right arrow keys. On this bar position 1 indicates
full red reflex and position 3 no red reflex. Click save icon once finished.
Always use the minimum light intensity possible
Excessive light intensity or long radiation exposure times
may lead to retinal injury in the patient's eye
Refer to:
Version 8.1
Page 178 G-30-
1673-en
Refer to:
Version 8.1
Page 184
G-30-1673-
Carl Zeiss Ltd
Customercare.uk@zeiss.com
01223 401450
Version 8.1
Page 234
G-30-1673-
en
Trouble Shooting
If the foot pedal has difficulties connecting, either use the cable provided to connect to the microscope directly, or in the Main Menu click on tab 2
and then system settings and click on the Pairing Icon.
The following may have been altered if you are having problems manoeuvring your microscope:
Blank screen. The I button may have been touched in error next to the on/off switch.
To return to a surgeon’s default setting, press the reset button situated above the overhead display.
To preserve the lamp life turn off the microscope by moving it upwards until it beeps. To turn on again just lower it slightly and it will turn on again.
Shut-down |
Turn off the microscope by the main power switch as before.
Version 8.1
Page 218
G-30-1673-
en
Version 8.1
Page 227
G-30-1673-
en
Version 8.1
G-30-1673-
en Page
203
Foot Control Panel
In the Main Menu, open the Additional Settings, then select Foot Control Panel
Each button on the panel can then be clicked on and assigned a specific function.
Once the foot control panel has been optimized to the surgeon’s preferences, click the save icon at the bottom.
Hand Grip
In the Main Menu, open the Additional Settings, then select Handgrip
Each button on the panel can then be clicked on and assigned a specific function.
Once the handgrip has been optimized to the surgeon’s preferences, click the save icon at the bottom.
Overhead Display
In the Main Menu, open the Additional Settings, then select Overhead Display
Switch on Overhead Display and adjust brightness by using up and down arrows on left hand side.
Click Save Icon at the bottom
Camera Settings
In the Main Menu, click on the Camera Icon, then click on White Balance.
This creates a prompt for you to hold a plain white paper under the microscope to perform the white balance.
Tabs 2 and 3 of the camera page allow customization of brightness and colour values.
Configure (optional)
In the Main Menu, select tab 2 and click on System Settings. Then click on the Recording Icon. On this tab the image format can be changed
to JPG or Tiff. On tab 2 storage of recordings can be selected to USB or Network. Click save icon on the bottom after any changes made.
Recording
In order to record images or videos, click on the Recording Icon in the Main Menu.
Then click on the Change button on the top right corner to input patient details.
Lastly select image or video icon.
Video can then be controlled with the icons at the bottom.
Video Recording
Version
8.1 Page
214 G-
30-1673-
en
Autres manuels pour opmi lumera 700
3
Table des matières
Autres manuels Zeiss Microscope
Zeiss
Zeiss Primostar 3 Manuel utilisateur
Zeiss
Zeiss Transillumination top 450 mot. Manuel utilisateur
Zeiss
Zeiss OPMI CS Manuel utilisateur
Zeiss
Zeiss Smartzoom 5 Manuel utilisateur
Zeiss
Zeiss SIGMA Series Manuel utilisateur
Zeiss
Zeiss LSM 710 Manuel utilisateur
Zeiss
Zeiss SV 6 Manuel utilisateur
Zeiss
Zeiss LSM 710 Manuel utilisateur
Zeiss
Zeiss Stemi 305 Manuel utilisateur
Zeiss
Zeiss JENAVAL Manuel utilisateur
Zeiss
Zeiss AxioImager A1 Instructions de montage
Zeiss
Zeiss OPMI PRO magis Manuel utilisateur
Zeiss
Zeiss OPMI 1FR XY Manuel utilisateur
Zeiss
Zeiss Axio Examiner Manuel utilisateur
Zeiss
Zeiss Axiocam MR Manuel d'installation et d'exploitation
Zeiss
Zeiss Stemi 305 cam Manuel utilisateur
Zeiss
Zeiss Stemi 305 Manuel utilisateur
Zeiss
Zeiss LSM800-02 Manuel de l'opérateur
Zeiss
Zeiss LSM 710 Manuel utilisateur
Zeiss
Zeiss Stemi 508 Manuel utilisateur
Manuels Microscope populaires d'autres marques
VWR
VWR VisiScope 384 Series Manuel utilisateur
Nikon
Nikon ECLIPSE E200 POL Manuel utilisateur
Leica
Leica DI C800 Manuel
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Manuel utilisateur
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Manuel utilisateur
Olympus
Olympus SZ61 Manuel utilisateur