Zeiss ELYRA Manuel utilisateur

Page | 1

Wellcome Trust Centre for Human Genetics

Cellular-Imaging Microscopy Core

The Zeiss Elyra TIRF

Confocal

Abridged INSTRUCTIONS

Page | 2

Introduction

The Zeiss Elyra TIRF PALM/STORM super-resolution microscope is located in

room 00/071, Lab 1 in the WTCHG building.

The new Zeiss Elyra TIRF microscope has:

•Zeiss Observer wide-field inverted TIRF flourescence microscope

•X-Cite 120Q fluorescence excitation illuminator

•Triple dichroic filter for FITC, TRITC and Cy5 far red

•NewPort Vision IsoStation anti-vibration isolation table for Elyra system

•PALM super-resolution illumination module

•Piezzo fast Z stage with 100μm range

•Motorised XY stage

•Black box XL stage incubator for super-resolution with temperature

control

•Plan Apochromat 10x NA 0.3 air objective

•Plan Apochromat 20x objective NA 0.8 air objective

•Alpha Plan Apochromat 100x NA 1.46 oil objective

•Andor iXon DU 897 EM-CCD (512x512 pixel) camera

•DAPI 405nm line 50mW diode laser

•GFP 488nm line 100mW laser

•DsRed 561nm line 100mW laser

•Imaging PC workstation for Elyra systems S.1, P.1 and PS.1

•30" LCD TFT PC monitor

•Zeiss ZEN Black image acquisition software with super-resolution

PALM/STORM module

•Two hardware USB2 licence keys for Zen Black imaging software, one

on the microscope PC and the other on the Core’s Imaging Workstation

To view the Ziess image files on your office PC you will need to download and

install Zeiss's Zen Lite program (Windows PCs only).

Page | 3

General information

The system can only image green GFP/FITC, red DsRed/RFP/TexsRed and blue

DAPI dyes.

The Andor iXon DU 897 EM-CCD camera has a maximum resolution of 512 x

512 pixels. It captures black and white images with a 16-bit depth of 65,536

grey levels (with 0 being pure black- and 65,535 being pure white).

Zen Black doesn’t automatically save images – you must save them as you go

along.

Use ‘snap’ in Zen Blue to clear noise from the camera detectors before

imaging. Setting ‘snap’ for every image will slow down acquisition a lot, but

you can just ‘snap’ clear at the beginning of an image sequence. Adjust

exposure time, laser power and EM Gain for brightness in ‘Acquisition’.

Unlike the Zeiss Spinning Disk microscope in OPIC, you can’t go above 300 in

EM Gain with the camera (it’s locked in software ). The EM Gain going from 1

to 200 goes from the equivalent of ½ second to a 20ms to frame rate. Avoid

putting too much light onto the cameras EMCCD sensor. The EM-CDD camera

is 16-bit (64,000 shades of grey).

Leave the Elrya system on for 5 minutes before scanning as the Andor EM-CCD

camera needs time for its electronics to cool down.

The system has three laser lines at 405nm DAPI, 488nm GFP and 561nm

TRITC/DsRed. There are four different emission filter sets for DAPI, GFP, DsRed

and Cy5 far red, selectable via Zen Black.

In Zen Black click Live for a faster ‘preview’ imaging with more noise.

You can save configurations and the menu screen setup in Zen Black. You can

reuse microscope settings from a stored image. The images are generally saved

in Zeiss *.czi format although you can use *.lsm. To prevent PC crashes with

Zen Black, it’s a good idea to limit the number of open images.

Log-in to the PC via the account ‘cyto\lsm user’.

Page | 4

The Zeiss Axio Observer Microscope

The Zeiss Elyra TIRF PALM/STORM super-resolution microscope mixes air (10x,

20x) and oil (100x) objectives. Make sure you use the appropriate immersion

fluid with the objective. The Ziess immersion oil for the 100x oil objective is

left on the air table. The oil immersion fluid is prone to drips from the

applicator so take care when using it not to overload the applicator.

It is far easier to control the DAPI, GFP and DsRed mercury lamp fluorescence

(as viewed down the eyepieces) from Zen Blue software.

Alcohol 70% is provided along with gloves and green-box lab tissues. These are

supplied for cleaning the samples and spillages and are not to be used on the

objectives. Be careful where you stand the 70% alcohol bottle as the alcohol

can drip out from the spout into electronics.

Only Whatman 105 Lens Cleaning tissues are to be used to wipe immersion oil

from the objectives. The air objectives shouldn’t need cleaning after use.

If you are using the heated incubator at 37oC you should switch on the

incubator at least 2 hours before imaging. For the most stable time-lapse

imaging at 37oC leave the incubator on overnight.

To view fluorescence down the microscope you have to press the X-Cite Start

(Stop) button or use the footswitch, so that the X-Cites ‘Open’ LED comes on.

You set the microscope to view down the eyepieces via Zen Black software,

under ‘Locate’. Set the emission filters to those required for the eyepieces

(FSet77HE, GFP/DsRed) and the lasers (other filters).

WARNING: To lift out the slide/Petri dish insert from the Piezzo Z motor stage

always pick up the insert by the two middle finger-grip indent holes – NEVER

use the levelling adjuster screws at the top left and bottom right.

The motorised Piezo Z stage is only controlled by the Zen Black software. The

microscope stand and the Zeiss microscope remote LCD station only move the

main microscope Z motor. The Piezo stage has a total range of 100um.

The two buttons on the right of the microscope on the focus knobs raise the

objectives to the work position (far button) and drop the objective to the load

position (near button).

Page | 5

The two buttons on the left side by the focus knob control the reflector turret

and light path (this is far easier selected by Zen Black software on the PC).

You can switch microscope objectives via the Zeiss microscope remote LCD

station or within Zen Black software.

There is no ‘definite focus’ autofocus hardware on the Elyra microscope.

The tube lens can be 1x or 1.6x – always use the 1.6x with super-resolution. If

the 1x tube lens is selected you can see the shadow of the 1.6x down the

microscope (vanishes when the 1.6x is selected).

You can do a multi-location time lapse with an identical z stack, and say a 3x3

raster scan at each location in time-lapse.

The Elyra isn’t a confocal and the Core’s Zeiss Spinning Disk confocal system

should be more ‘gentle’ with live cells. Start with lower laser power as the

Elyra has high powered lasers (around 100mW).

Page | 6

The X-cite Series 120PC Q

The X-Cite takes a minute or so warm up

Use the Mode button to select three modes:

1. Press mode and when OOOO. appears on the display this is the number

of hours the arc lamp has been on

2. Press mode and when OOO.O appears on the display this is the timer

mode. The display is in seconds and 1/10 seconds. It times how long the

lamp will be on in seconds. Set the time and press Start (Stop) and lamp

will come on and the timer will count down to switch-off.

3. Press mode and when OOO appears on the display this is the lamp

intensity. Press Up/Down to select 0, 12, 25, 50 and 100% lamp

intensity. Warning things can very bright down the eyepieces even with

the standard FITC/TRITC/Far red triple filter selected.

Press Start/Stop to switch open/close the X-Cite shutter and illuminate the

specimen. The footswitch under the microscope also activates the Start/Stop

sequence.

Note that the Excite 120PC Q only works with the triple filter block FSet77HE

(for GFP/DsRed/Cy5 only and so no DAPI) when viewing down the eyepieces.

The triple filter FSet77HE excites at 483 + 564 + 642 nm (HE) and shows all

three fluorescence colours at the same time, although our eyes can’t see the

far red Cy5 emission.

Page | 7

Zeiss Elyra Operating Manual

For details on the operation of the Elrya TIRF super-resolution microscope see

the Ziess Elyra manual, and in particular the ‘Elyra Quick Guide’ (after chapter

7 of the manual) – a pdf download of the Quick Guide is available via the Core’s

Elyra web-pages.

Page | 8

Switch on Procedure

1) Switch on all the labelled 13A mains sockets with the Microscope + X-

Cite socket on first.

2) All the microscope control boxes including the Andor EM-CCD camera

should come on with the exception of the Tokai Hit incubator heater

unit that is only switched on as required.

3) Switch on the system PC and 32” monitor and login to the WTCHG

network.

4) Start Zen Black (don’t select the Zen Blue option as that is for off-line

image analysis only). Start up the Elyra hardware via the software

prompt.

5) Place the specimen onto the microscope

6) Use the triple filter block FSet77HE (GFP/DsRed) or BF (bright field

transmission) to view the specimen down the microscope via the

eyepieces (filter selection and open/close shutters options are under

‘Locate’ in Zen Black).

7) Use the X-Cite footswitch or Start-Stop button to illuminate the

specimen with excitation light, in combination with open/close filter

options in Zen Black.

8) Ensure that the doors and viewing panels are closed on the black stage

incubator or the lasers will switch off. Wait ~5 minutes until the Andor

EM-CCD camera electronics have cooled down before acquiring images.

9) Go to Acquisition in Zen Black to capture images

The microscope stand must not be left pushed backwards on the microscope or the

lasers will not fire (there is a safety cut-out).

10) Create and save filter and EM-CCD camera settings for the

fluorochromes in your sample.

11) Leave the Elrya microscope system on for at least 5 minutes before

scanning as the Andor EM-CCD camera needs time for its electronics to

cool down.

12) The system has three laser lines at 405nm DAPI, 488nm GFP and

561nm TRITC/DsRed. There are four different emission filter sets for

DAPI, GFP, DsRed and Cy5 far red, selectable via Zen Black.

Warning: The Elyra lasers are shuttered off by magnetic micro-switches if one of the

access doors is left open on the blackened live cell incubator chamber.

Page | 9

Switch off procedure

1) Remove the specimen from the microscope stage

2) Wipe off excess immersion fluid from the 100x oil objective lens/top

using the Whatman 105 lens cleaning tissues provided

The 10x and 20x air objectives don’t need cleaning after use.

3) Leave the 10x objective selected on the microscope nose-piece to

minimise any possibility of damage during start-up when the XY

motorised stage initialises

Note: The top of the 100x objective rotates, so avoid accidently turning it.

4) Drop the 10x objective nearer to the Load (lowest) position using the

microscope coarse focus control

5) Transfer image files to the network or data key

6) Shut Down the PC workstation

7) Switch off all 13A mains sockets around the microscope, leaving the

modules switched on

8) Tidy up the microscope area and leave.

9) Switch the room light, desk lamp, and red lamps off as you leave the

room.

Page | 10

________________________________________________________________

If you have any microscope/imaging problems or queries, just ask a member of

the Microscopy Core staff for help.

There is additional help and advice on our Core web-pages:

http://www.well.ox.ac.uk/microscopy

WTCHG Zeiss Cell Observer SD microscope user guide. This version updated 26th June 2014.

Autres manuels pour ELYRA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Zeiss Microscope

Zeiss

Zeiss LSM800-6 Manuel utilisateur

Zeiss

Zeiss LSM 710 SIM Manuel utilisateur

Zeiss

Zeiss JENAVAL Manuel utilisateur

Zeiss

Zeiss LSM 700 Manuel utilisateur

Zeiss

Zeiss Axio Observer Series Manuel utilisateur

Zeiss

Zeiss Smartzoom 5 Manuel utilisateur

Zeiss

Zeiss VISU 200 Manuel utilisateur

Zeiss

Zeiss Axioskop 2 FS plus Manuel utilisateur

Zeiss

Zeiss Stemi 508 Manuel utilisateur

Zeiss

Zeiss opmi lumera 700 Manuel utilisateur

Zeiss

Zeiss Axioscope 5 Manuel utilisateur

Zeiss

Zeiss Axioskop 2 Manuel utilisateur

Zeiss

Zeiss LSM 710 Manuel utilisateur

Zeiss

Zeiss Axiostar plus Manuel utilisateur

Zeiss

Zeiss Cell Observer spinning disk confocal Manuel utilisateur

Zeiss

Zeiss Axioskop 40 Manuel utilisateur

Zeiss

Zeiss Axio Observer Series Manuel utilisateur

Zeiss

Zeiss Axiovert 200 Manuel utilisateur

Zeiss

Zeiss EVO Manuel utilisateur

Zeiss

Zeiss Axiocam MR Manuel d'installation et d'exploitation

Zeiss

Zeiss AxioImager A1 Instructions de montage

Zeiss

Zeiss OPMI Pentero Manuel utilisateur

Zeiss

Zeiss LSM 880 Manuel d'utilisation et d'entretien

Zeiss

Zeiss IV FL Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur