Yale 628F Manuel utilisateur

628F Exit Device Trim

Installation Instructions

For use with Yale® 7000, 2100,

1800 or 1500 Series Exit Devices

(Wood and Metal Doors)

628F Series

Passage Function Trim

Handed (RHR or LHR)

Lever Always Active

(76)

10-1/4

(260)

Attention Installer

Any retrofit or other field modification to a fire rated opening can potentially

impact the fire rating of the opening, and Yale Locks & Hardware makes no

representations or warranties concerning what such impact may be in any

specific situation. When retrofitting any portion of an existing fire rated

opening, or specifying and installing a new fire-rated opening, please consult

with a code specialist or local code official (Authority Having Jurisdiction) to

ensure compliance with all applicable codes and ratings.

An ASSA ABLOY Group brand

80-8470-0628-000 (11-18)

Escutcheon Assembly

Lever is handed, RHR (shown)

or LHR.

Note: Lever return spring is universal

for easy field handing.

See page 5 to change handing.

(2) #14 Finishing Washers

Trim Spindle

Assembly

(2) 1/4-20 Pan Head

Machine Screws

Packed with device.

(2) 1/4-20 Oval Head

2 STUDS AWAY

FROM LOCK EDGE

2 STUDS TOWARDS

LOCK EDGE

An ASSA ABLOY Group brand

80-8470-0628-000 (11-18)

WARNING

This product can expose

you to lead which is

known to the state of

California to cause cancer

and birth defects or other

reproductive harm. For

more information go to

www.P65warnings.ca.gov.

08/2018

NOTE : Measure from device mounting

surface (door face or shim surface).

1. Assemble trim. See previous page for

components.

2. After marking door inside face for device

location (Device Instructions) transfer Vertical

Reference Centerline from inside to outside

door face. Follow steps 2a and 2b below.

3. Transfer Horizontal Reference Centerline from

inside to outside door face.

4. Align trim template and tape to outside door

face.

5. Spot holes and prepare door for trim.

6. Mount trim to door thru holes "B". Fasten finger

tight only with 2 screws and washers seating

on door as shown in Figure 1.

7. Cut trim tailpiece as shown in Figure 2.

8. Seat device so that trim tailpiece penetrates

cam slot as shown in Figure 1. Continue as

shown in device instructions.

Device is bolted

to trim using

holes "A" (closest

to door lock edge).

(2) Screws and

washers bolt trim

to door using

holes "B".

Tailpiece (T)

engages with

cross hole of

cam slot.

Cut per Fig 2.

Device

Mounting

Surface

(See Note)

Trim

Mounting

Surface

Trim

Tailpiece

Door

Thickness

Cut Line

Hold 5/16

(8)

An ASSA ABLOY Group brand

80-8470-0628-000 (11-18)

CAUTION: Office copiers and facsimile mach-

ines may change the size of a drawing and make

the template inaccurate to use as a door marker.

If this is not the original template packed with the

trim, use only the holes on the door (do not use

template as a door marker).

1-1/8

(29)

1-1/8

(29)

An ASSA ABLOY Group brand

80-8470-0628-000 (11-18)

An ASSA ABLOY Group brand

80-8470-0628-000 (11-18)

How to Change Handing

626F, 627F, 628F, 690F and 691F Series Exit Device Trim

Right Hand Reverse Gear & Spring Orientation

Left Hand Reverse Gear & Spring Orientation

Notes:

1. During change ensure black driven gear does not rotate.

2. Please wear safety glasses and be aware of spring tension on spring hub upon removal and assembly.

3. Light lubrication is recommended under flat gear, white lithium grease can be used.

An ASSA ABLOY Group brand

80-8470-0628-000 (11-18)

1. Remove cotter pin.

2. Remove castle nut.

3. Remove washer.

4. Carefully pull up on spring hub to

disengage spring.

5. Remove spring and note orientation.

6. Remove lever handle.

7. Pick-up flat gear, flip and orient stop on

opposite side of stop post. See pictures

for orientation.

8. Install spring upside down from original

orientation and place spring leg on

opposite side of stop post from original

installation orientation. See pictures for

orientation.

9. Install lever 180 degrees from original

position.

10. Install spring hub with stamped number

in the 6 o'clock position.

11. Rotate spring leg around with needle

nose pliers to engage notch in spring

hub, refer to pictures for reference

position. Press down on spring hub to

ensure complete engagement.

12. Install washer.

13. Install castle nut, do not over tighten,

verify by insuring lever returns

horizontally on its own.

14. Install cotter pin.

Tools Needed: Needle Nose pliers, Crescent wrench.

To Change Hands:

Notch for spring to engage for left hand reverse operation

Spring orientation for right hand reverse operation

LEFT HAND REVERSE

Castle Nut Spring Hub

Flat Gear

Stop Post

Cotter Pin

RIGHT HAND REVERSE

Castle Nut Spring Hub

Flat Gear

Stop Post

Cotter Pin

Product Support Tel 800.438.1951 • www.yalelocks.com

Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their

respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.

Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.

Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.

Autres manuels Yale Verrouillage

Yale

Yale nexTouch Caractéristiques techniques

Yale

Yale Assure Lock Lever Touchscreen YRL226 Caractéristiques techniques

Yale

Yale Real Living Assure Lock YRD226 Caractéristiques techniques

Yale

Yale 5400LN SERIES Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Guide de démarrage rapide

Yale

Yale 5300LN Grade 2 Manuel utilisateur

Yale

Yale Assure Lock SL YRD256 Caractéristiques techniques

Yale

Yale Luna Pro+ Manuel utilisateur

Yale

Yale YDR323 Manuel utilisateur

Yale

Yale 5400LN SERIES Manuel

Yale

Yale eBOSS E5400LN Series Manuel utilisateur

Yale

Yale YRC216 Caractéristiques techniques

Yale

Yale D100 Series Manuel utilisateur

Yale

Yale YRD246 Caractéristiques techniques

Yale

Yale Real Living Touchscreen Lever Guide d'installation

Yale

Yale Real Living Assure Lock YRD226 Caractéristiques techniques

Yale

Yale Quattro Sliding 3 Manuel utilisateur

Yale

Yale 8880 Manuel utilisateur

Yale

Yale Doorman Manuel utilisateur

Yale

Yale Keyfree Connected Smart Lock Manuel utilisateur

Yale

Yale Assure Lock YRC226 Caractéristiques techniques

Yale

Yale Assure Lock YRD426 Caractéristiques techniques

Yale

Yale YDM3109+ Manuel utilisateur

Yale

Yale Assure Lock YRD216 Caractéristiques techniques

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur