Westermo Lynx DSS L206-S2 Manuel utilisateur
www.westermo.com
Lynx DSS
L106-S2/L206-S2
Industrial Ethernet
6-port Device Server Switch
WeOS
26643-2240
3
6643-2240
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind, either express or implied, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose, are made in
relation to the accuracy and reliability or contents of this document. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following address:
www.westermo.com
Software tools
Related software tools are available in the folder software tools under technical support
on the Westermo website.
License and copyright for included Free/Libre Open Source Software
This product includes software developed by third parties, including Free/Libre Open
Source Software (FLOSS). The specific license terms and copyright associated with the
software are included in each software package respectively. Please visit the product web
page for more information.
Upon request, the applicable source code will be provided. A nominal fee may be charged
to cover shipping and media. Please direct any source code request to your normal sales
or support channel.
WeOS Management Guide
This product runs WeOS (Westermo Operation System). Instructions for quick start,
configuration, factory reset and use of USB port are found in the WeOS Management
Guide at www.westermo.com.
46643-2240
Safety
Before installation:
Read this manual completely and gather all information on the unit. Make sure that
you understand it fully. Check that your application does not exceed the safe operating
specifications for this unit.
Warning - Hazardous voltage
The product must be installed by qualified service personnel
and built in to an apparatus cabinet or similar, where access is
restricted to service personnel only.
Before powering up, a protective earthing conductor must
be connected to the protective earthing terminal. Westermo
recommends a cross-sectional area of at least 4 mm2 on the
protective earthing conductor.
Do not open a connected product. Hazardous voltage may occur
when connected to a power supply.
Disconnect all network connectors and cable distribution system
connectors, including power supply, before disconnecting the
protective earthing terminal.
Warning - Protective fuse
The power supply wiring must be sufficiently fused. It must be
possible to disconnect manually from the power supply. Ensure
compliance to national installation regulations. Refer to the user
guide for detailed information.
Replacing the internal fuse must only be performed by Westermo
qualified personell.
Warning - Reduce the risk of fire
To reduce the risk of fire, use only no. AWG 26 or larger
telecommunication line cord.
5
6643-2240
Caution - Electrostatic discharge (ESD)
Prevent damage to internal electronic parts from electrostatic
discharge (ESD) by discharging your body to a grounding point
(e.g. use of a wrist strap).
Caution - Hot surface
Be aware of that the surface of this product may become hot.
When it is operated at high temperatures, the external surface
may exceed Touch Temperature Limit according to EN/IEC/UL
60950-1.
Westermo’s products are fanless and use convection cooling.
To avoid obstructing the airflow around the product, follow the
spacing recommendations.
Caution - Wiring
Ensure that the temperature rating of the cable is sufficient for the
application before connecting to the field wiring terminals.
Note
This unit can be connected to two different power sources.
66643-2240
Product disposal
This symbol means that the product shall not be treated
as unsorted municipal waste when disposing of it. It needs
to be handed over to an applicable collection point for
recycling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfill
the warranty obligations:
• Do not drop, knock or shake the unit. Rough handling above the specification may
cause damage to internal circuit boards.
• Do not use harsh chemicals, cleaning solvents or strong detergents to clean the
unit.
• Do not paint the product. Paint can clog the product and prevent proper operation.
If the unit is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo technical support.
7
6643-2240
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
Safety UL/IEC/EN 60950-1, IT equipment
Marine DNV GL rules for classification – Ships and offshore units
FCC Part 15.105
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
… Reorient or relocate the receiving antenna
… Increase the separation between the equipment and receiver
… Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.
Corrosive
environment
Notice:
This product has been successfully tested in a corrosion test according to IEC 60068-
2-60, method 3. This means that the product meets the requirements to be placed in an
environment classified as ISA-S71.04 class G3.
Simplified EU declaration of conformity
Hereby, Westermo declares that the equipment is in compliance with EU directives. The
full EU declaration of conformity and other detailed information are available at the
respective product page at www.westermo.com. .
Caution - Corrosive gases
If the product is placed in a corrosive environment, it is important
that all unused connector sockets are protected with a suitable
plug, in order to avoid corrosion attacks on the gold plated
connector pins.
86643-2240
Type tests and environmental conditions
Environmental phenomena Basic standard Description Test levels
Electrostatic discharge EN 61000-4-2 Enclosure Contact: ±6 kV
Air: ±8 kV
Fast transients EN 61000-4-4 Power port ±2 kV
Ethernet
Status out/Digital in
Serial ports
Enclosure
Surge EN 61000-4-5 Power port L-L: ±0.5 kV, 2 Ω, 18 μF
L-E: ±2 kV, 42 Ω, 0.5 μF
L-L: ±1 kV, 42 Ω, 0.5 μF
L-E: ±2 kV, 12 Ω, 9 μF
L-L: ±1 kV, 12 Ω, 9 μF
Ethernet L-E: ±2 kV, 2Ω, 0.5 μF
Status out/Digital in L-E: ±2 kV, 42 Ω, 0.5 μF
L-L: ±1 kV, 42 Ω, 0.5 μF
RS-232 L-E: ±2 kV, 2 Ω, 0.5 μF
RS-422/485 L-E: ±2 kV, 42 Ω, 0.5 μF
Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 60 Hz
1000 A/m; 50 Hz
Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m
Radiated RF immunity EN 61000-4-3 Enclosure 20 V/m @ (80 – 2700) MHz
10 V/m @ (2700 – 6000) MHz
1 kHz sine, 80% AM
Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Ethernet
Status out/Digital in
Serial ports
Earth port
Radiated RF emission CISPR 16-2-3
ANSI C63.4
(FCC Part 15)
Enclosure Class B / DNV bridge
Conducted RF emission CISPR 16-2-1
ANSI C63.4
(FCC Part 15b)
Power port Class B / DNV bridge
Ethernet Class B
Dielectric strength EN 60950-1 Power port to all
other ports
1.5 kVrms, 50 Hz, 1 min
Ethernet ports to all
other ports
RS-232 port to all
other ports
RS-422/485 port to all
other ports
9
6643-2240
Environmental
Temperatures EN 60068-2-1
EN 60068-2-2
Operating –40 to +70°C (–40 to +158°F)*
Storage and transport –50 to +85°C (–58 to +185°F)
Humidity EN 60068-2-30 Operating 5 to 95 % relative humidity
Storage and transport 5 to 95 % relative humidity
Altitude Operating 2 000 m / 70 kPa
MTBF MIL-C217F2,
Parts count
Ground Benign, 25°C
(77°F)
593 000 hours
Service life Operating 10 year
Vibration IEC 60068-2-6
(sine)
Operating 3 – 13.2 Hz: 1mm
13.2 – 100 Hz: 0.7 g
5.5 – 30 Hz: 1.5 g
30 – 50 Hz: 0.42 mm
50 – 500 Hz: 4.2 g**
IEC 60068-2-64
(random)
5 – 20 Hz: 2 m²/s³,
20 – 2000 Hz: – 3 dB/oct
Shock IEC 60068-2-27 Operating 30 g, 11 ms
100 g, 6 ms**
Bump IEC 60068-2-27 Operating 10 g, 11 ms
Packaging
Enclosure EN 60950-1 Zinc Fire enclosure
Dimension W x H x D
With connectors
52.5 x 100 x 101 mm
52.5 x 119 x 101 mm
Weight 0.7 kg
Degree of protection EN 60529 Enclosure IP 40
Cooling Convection
* Refer to “Safety” section in User Guide.
** Might require Ethernet cables to be fastened close to the unit.
Description
L106-S2/L206-S2 is an Industrial switch and device server made for harsh environments.
WeOS is the operating system of L106-S2/L206-S2 enabling the unit to operate in two
functional levels. The switch can be used in either 10 or 100 Mbit networks.
Lynx DSS L106-S2/L206-S2 has two serial ports, one that supports RS-232 and the other
configurable for RS-232/422/485 as well as serial protocols for interconnection with
legacy equipment.
Our unique FRNT (Fast Recovery of Network Topology) technology is the fastest
protocol on the market to re-configure a network in the event of any link or hardware
failure. That is why our equipement are used in safety critical applications such as tunnels,
traffic signal control and railway systems.
10 6643-2240
Interface specifications
Power
Operating voltage Rated: 24 to 48 VDC
Operating: 19 to 60 VDC
Rated current 150 mA (300 mA) @ 24 VDC (with 500 mA USB load)
80 mA (150 mA) @ 48 VDC (with 500 mA USB load)
Rated frequency DC
Inrush current, I2t 22.7·10-3 A2s @ 48 VDC
Startup current* 2 x Rated current
Polarity Reverse polarity protected
Redundant power input Ye s
Isolation to All other
Connection Detachable screw terminal
Conductor cross section 0.2 – 2.5 mm2(AWG 24 – 12)
Stripping length cable 7 mm
Tightening torque, terminal screw 0.5-0.6 Nm
Tightening torque, screw flange 0.3 Nm
Shielded cable Not required
* External supply current capability for proper start-up
Ethernet TX
Electrical specification IEEE std 802.3. 2005 Edition
Data rate 10 Mbit/s, 100 Mbit/s, manual or auto
Duplex Full or half, manual or auto
Circuit type TNV-1
Transmission range Up to 150 m with CAT5e cable or better*
Isolation to All other
Connection RJ-45, auto MDI/MDI-X
Cabling Shielded CAT5e or better is recommended
Conductive housing Ye s
Number of ports 4
* Refer to Safety section.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Westermo Changer
Westermo
Westermo Viper TBN Series Manuel utilisateur
Westermo
Westermo Lynx DSS L108-F2G-S2 EX Manuel utilisateur
Westermo
Westermo Lynx L106-S2 Manuel utilisateur
Westermo
Westermo Lynx DSS L108-F2G-S2 EX Manuel utilisateur
Westermo
Westermo Lynx SERIES Manuel utilisateur
Westermo
Westermo RedFox Series Manuel utilisateur
Westermo
Westermo RedFox 5528 Series Manuel utilisateur
Westermo
Westermo SD-300 Series Manuel utilisateur
Westermo
Westermo Lynx 5500 Series Manuel utilisateur
Westermo
Westermo RedFox-5528-E-T28G-LV Manuel utilisateur
Westermo
Westermo Viper-TBN Series Manuel utilisateur
Westermo
Westermo SDW-500 Manuel utilisateur
Westermo
Westermo RedFox Industrial EX Series Manuel utilisateur
Westermo
Westermo Lynx L210-F2G-EX Manuel utilisateur
Westermo
Westermo Lynx L206-F2G Manuel utilisateur
Westermo
Westermo RedFox 7528 Series Manuel utilisateur
Westermo
Westermo RFIR-127-F4G-T7G-DC Manuel utilisateur
Westermo
Westermo Lynx 3000 Series Manuel utilisateur
Westermo
Westermo U200 series Manuel utilisateur
Westermo
Westermo Lynx DSS L108-F2G-S2 EX Manuel utilisateur
