WE-EF ETC320-FS LED Manuel utilisateur
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETC320-FS LED
EVC320-FS LED
1
IP67, Class I, ta = 25C
Inground Luminaire
EVC320-FSETC320-FS
2
Light Source
LED
Maintenance
Apart from cleaning the outside of the luminaire, no special maintenance is necessary.
Luminaire should be discarded in case the supply cable is damaged.
3
Installation Methods
Important: The luminaire is factory-sealed and does
not need to be opened during installation.
Ensure that proper drainage is provided for the shown
installation methods.
For proper installation use the supplied installation
blockout.
Please note the following installation possibilities:
1) In landscape areas, sand with gravel base (Fig. I).
2) In paved areas, concrete with gravel base (Fig. II).
Fig. I
Fig. II
Installation
The product must be installed and maintained by a
suitably qualified person in compliance with the latest
applicable regulations and relevant legislation.
When selecting the correct location for the luminaire,
it is important to remember that the lens will reach a
high temperature during operation.
The minimum distance of an object to be illuminated
must be observed (see illustration ------minside
luminaire).
Ensure the luminaire and lens is clear of dirt and
debris.
Claims based on defects attributable to improper
installation, application, operation and/or any modi-
fication carried out by the purchaser or third parties,
and the consequences thereof, are excluded.
4
Phase One
Blockout Installation Procedure
(during earth or masonry work)
1) A suitable recess to be provided to accommodate
installation blockout/mounting ring assembly B/M.
2) Set installation blockout/mounting ring assembly
B/M in position and ensure that:
a) Arrow Ron mounting ring Mis pointed towards
the object to be illuminated (wall, tree, column).
b) Mounting ring Mis flush with surface. If the
floor will be tiled or paved afterwards leave an
appropriate gap.
c) Mains supply cable(s) Ois of sufficient length to
connect the sealable junction box Jwith the cable
Efrom luminaire.
3) During ongoing earth and/or masonry works, do
not remove the two stickers on fixing thread holes
D. Ensure that installation blockout/mounting ring
assembly B/M is not damaged and has maintained
its original shape. If necessary use a cover plate.
Phase Two
Luminaire Installation and Electrical Connection
4) Switch off mains electrical supply.
5) Check that rating shown on luminaire label con-
forms with mains electrical supply.
6) Terminate cable Efrom luminaire housing Aand
mains supply cable O(for individual wiring) or
branch cable (for through wiring) in sealable junc-
tion box Jto connect cable(s). Follow the sealable
junction box termination instruction included in the
packaging.
7) Peel-off the two stickers on fixing thread holes D.
Set cables and sealable junction box Jinside the
installation blockout/mounting ring assembly B/M.
Caution: When the luminaire is placed inside the
installation blockout B, make sure that there is no
stress on the sealable junction box Jor electric
cables (Fig. lll).
8) Loosen the two countersunk screws C (do not twist
out). Insert mounting lever Lbetween head of
countersunk screws C and cover lens. Lift luminaire
housing Ainto installation blockout/mounting ring
assembly B/M(Fig. IV) while aligning holes Don
mounting ring M.
9) Tighten both countersunk screws C 'hand tight'.
5
J
B
E
R
D
O
E
O
A
M
B
Fig. III
6
L
M
C
A
Fig. IV
7
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel +49 5194 909-0
Fax +49 5194 909-299
info.germany@we-ef.com
WE-EF HELVETICA
Switzerland
Tel +41 22 752 49 94
Fax +41 22 752 49 74
info.switzerland@we-ef.com
WE-EF LIGHTING
United Kingdom
Tel +44 844 880 5346
Fax +44 844 880 5347
info.uk@we-ef.com
WE-EF LIGHTING
Thailand
Tel +66 2 738 9610
Fax +66 2 175 2174
info.asiapacific@we-ef.com
WE-EF LUMIERE
France
Tel +33 4 74 99 14 44
Fax +33 4 74 99 14 40
info.france@we-ef.com
WE-EF ILLUMINAZIONE
Italy
Tel +39 029 0092354
info.italy@we-ef.com
WE-EF LIGHTING
United States of America
Tel +1 724 742 0030
Fax +1 724 742 0035
info.usa@we-ef.com
WE-EF LIGHTING
Australia
Tel +61 3 8587 0444
Fax +61 3 8587 0499
info.australia@we-ef.com
TO9197W0714 © WE-EF 2014
Technical specifications are
subject to change.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels WE-EF Lanterne
WE-EF
WE-EF ETC330-FS Manuel utilisateur
WE-EF
WE-EF AL530 Manuel utilisateur
WE-EF
WE-EF XLO200 LED Series Manuel utilisateur
WE-EF
WE-EF ASP500 LED Manuel utilisateur
WE-EF
WE-EF ASP500 LED Manuel utilisateur
WE-EF
WE-EF PFL240 LED Manuel utilisateur
WE-EF
WE-EF RBL640 Manuel utilisateur
WE-EF
WE-EF RLS410 LED Manuel utilisateur
WE-EF
WE-EF RMC320 LED Manuel utilisateur
WE-EF
WE-EF VFL530-SE LED Manuel utilisateur
WE-EF
WE-EF VFL500 LED Series Manuel utilisateur
WE-EF
WE-EF ALP530 Manuel utilisateur
WE-EF
WE-EF ETC130-FS LED Manuel utilisateur
WE-EF
WE-EF RFL500-SE Series Manuel utilisateur
WE-EF
WE-EF RLS400 LED Series Manuel utilisateur
WE-EF
WE-EF PFL230 Manuel utilisateur
WE-EF
WE-EF ETC100-GB LED Series Caractéristiques techniques
WE-EF
WE-EF ETC330-GB LED Manuel utilisateur
WE-EF
WE-EF QLS410 LED Manuel utilisateur
WE-EF
WE-EF VFL500 LED Series Manuel utilisateur
