Water Specialist WS1TT Manuel utilisateur

In/Out Head

Control

Valve

Treated

Water

Outlet

Untreated

Water

Inlet

Proper installation shown above.

See page 2 for issues that arise if the in/out head is incorrectly connected to the

untreated water inlet/treated water outlet of the control valve, rather than to the 2nd tank connection ports.

2nd Tank

Connection

Port

2nd Tank

Connection

Port

Water Specialist

WS1TT Drawings and Service Manual

HYDROCARBONS SUCH AS KEROSENE, BENZENE, GASOLINE, ETC., MAY DAMAGE

PRODUCTS THAT CONTAIN O-RINGS OR PLASTIC COMPONENTS. EXPOSURE TO

SUCH HYDROCARBONS MAY CAUSE THE PRODUCTS TO LEAK. DO NOT USE THE

PRODUCT(S) CONTAINED IN THIS DOCUMENT ON WATER SUPPLIES THAT CONTAIN

HYDROCARBONS SUCH AS KEROSENE, BENZENE, GASOLINE, ETC.

Page 2 WS1TT Drawings and Service Manual

We have had a number of instances where customers have incorrectly installed the in/out head to the untreated

water inlet/treated water outlet of the control valve, rather than to the 2nd tank connection ports.

Below are a number of situations that will occur when the in/out head is incorrectly installed to the untreated

water inlet/treated water outlet of the control valve.

1) When “A” is in the draw cycle it will not draw brine and will put water into the salt tank. The “B” tank will

draw properly.

2) When “B” is in the backwash cycle, “A” will have no ﬂow to service.

3) The transfer disc seals may be forced out of their cavities on the back/motor side of the transfer discs, and

it is possible that one of the seals could get pushed up into the valve and get stuck in the top of tank port of

the spacer stack assembly.

Twin Valve Installation Tips:

WS1TT Drawings and Service Manual Page 3

Valve Body Compliance Table ................................................................................................................................................... 4

Drive Cap Assembly, Downﬂow Piston, Upﬂow Piston, Regenerant Piston and Spacer Stack Assembly................................ 5

Twin Transfer.............................................................................................................................................................................. 6

Injector Cap, Injector Screen, Injector, Plug and O-Ring........................................................................................................... 8

Injector Order Information ......................................................................................................................................................... 9

Injector Graphs US Units: Injector Draw, Slow Rinse and Total Flow Rates .......................................................................... 10

Injector Graphs Metric Units: Injector Draw, Slow Rinse and Total Flow Rates..................................................................... 12

Reﬁll Flow Control Assembly and Reﬁll Port Plug..................................................................................................................14

Drain Line – 3/4” ...................................................................................................................................................................... 15

Drain Line – 1” ......................................................................................................................................................................... 16

Interconnect Fitting Assembly.................................................................................................................................................. 19

General Information......................................................................................................................................................................... 20

General Warnings (Must appear in OEM’s manual) ................................................................................................................ 20

Quick Reference Speciﬁcations................................................................................................................................................ 22

Drive Assembly ........................................................................................................................................................................ 23

Drive Cap Assembly, Main Piston and Regenerant Piston....................................................................................................... 24

Spacer Stack Assembly............................................................................................................................................................. 24

Injector Cap, Screen, Injector Plug and Injector....................................................................................................................... 24

Reﬁll Flow Control Assembly or Reﬁll Port Plug.................................................................................................................... 24

Drain Line Flow Control and Fitting Assembly ....................................................................................................................... 25

Service Instructions.......................................................................................................................................................................... 26

Servicing Transfer Cap Assemblies ................................................................................................................................................. 30

Troubleshooting ............................................................................................................................................................................... 32

Limited Warranty ............................................................................................................................................................................. 36

Table of Contents

Page 4 WS1TT Drawings and Service Manual

Application Injector and/or

Plug(s)

Main

Piston

Regenerant

Piston Stack Body*

1” Downﬂow Softener or

Regenerating Filter

Injector in “DN”

hole, Plug in “UP”

hole

V3011 V3174 V3005 V3031

1” Backwash Only Filter

Plug in “DN” and

“UP” holes, Install

Reﬁll Port Plug

V3011 None V3005 V3031

1” Upﬂow Softener

Injector in “UP”

hole, Plug in

unlabeled hole

V3011-01 V3174 V3005 V3031

Valve Body Compliance Table

WS1TT with 1.050" Distributor Tube Opening Identication

D



1.25"

Spacer Color:

Grey

Note: The downow piston is a solid amber color. The upow piston is black and amber.

WS1TT Drawings and Service Manual Page 5

Drive Cap Assembly, Downow Piston, Upow Piston, Regenerant Piston and Spacer Stack Assembly

Drawing No. Order No. Description Quantity

1 V3005 WS1 Spacer Stack Assembly 1

2 V3004 Drive Cap ASY 1

3a V3011* WS1 Piston Downﬂow ASY 1

3b V3011-01* WS1 Piston Upﬂow ASY

4 V3174 WS1 Regenerant Piston 1

5 V3135 O-ring 228 1

*V3011 is labeled with DN and V3011-01 is labeled with UP. Upﬂow option is not

applicable to EA, EE or EI control valves.

Note: The regenerant piston is not used in backwash only applications.

Refer to programming and Cover Drawing Manual

Page 6 WS1TT Drawings and Service Manual

14 15

Twin Transfer

WS1TT Drawings and Service Manual Page 7

Drawing No. Order No. Description Quantity

1 V3470 SCREW BHC 1/4-20 X 1 SS 12

2 V3724 WASHER FLAT SS 1/4 12

3 V4005-01 T1 TRANSFER CAP ASY 1

4 V4029 O-RING 236 2

5 V4015 T1 TRANSFER SPRING 2

6 V4014 T1 TRANSFER SPRING SUPPORT 2

7 V4036 T1 ROTOR DISK ASY 2

8 V3105 O-RING 215 (DISTRIBUTOR TUBE) 1

9 V3180 O-RING 337 1

10 V4016 T1 TRANSFER SEAL 6

11 V3031 T1 BODY SFT WTR REGEN 1

12 V4023 T1 TRANSFER DRIVE SHAFT ASY 1

13 V3287 O-RING 110 2

14 V4006-01 T1 TRANSFER DRIVE CAP ASY 1

15 V4011-01 T1 TRANSFER DRIVE GEAR ASY 1

16 V4012 T1 TRANSFER DRIVE GEAR AXLE 1

17 V4013 T1 TRANSFER REDUCTION GEAR 1

18 V3264 WS2H BYPASS REDUCTION GEARAXLE 3

19 V3110 WS1 DRIVE REDUCING GEAR 12X36 3

20 V3262-01 WS1.5&2ALT/2BY REDUCGEARCVRASY 1

21 V3592 SCREW #8-1 PHPN T-25 SS 3

22 V4049 T1 COVER ASSEMBLY 1

NOT SHOWN V4043 T1 TRANSFER MOTOR ASY 1

NOT SHOWN V3151 WS1 NUT 1 QC 1

NOT SHOWN V4055* TWIN TANK METER ASY 1

NOT SHOWN V4017-01 T1 INTERCONNECT FITTING ASY 1

NOT SHOWN D1400 1191 IN/OUT HEAD 1

*THIS WATER METER SHOULD NOT BE USED AS THE PRIMARY MONITORING DEVICE FOR

CRITICAL OR HEALTH EFFECT APPLICATIONS.

Twin Transfer

Page 8 WS1TT Drawings and Service Manual

Injector Cap, Injector Screen, Injector, Plug and O-Ring

Drawing No. Order No. Description Quantity

1 V3176 INJECTOR CAP 1

2 V3152 O-RING 135 1

3 V3177-01 INJECTOR SCREEN CAGE 1

4 V3010-1Z WS1 INJECTOR ASY Z PLUG 1

V3010-1A WS1 INJECTOR ASY A BLACK

V3010-1B WS1 INJECTOR ASY B BROWN

V3010-1C WS1 INJECTOR ASY C VIOLET

V3010-1D WS1 INJECTOR ASY D RED

V3010-1E WS1 INJECTOR ASY E WHITE

V3010-1F WS1 INJECTOR ASY F BLUE

V3010-1G WS1 INJECTOR ASY G YELLOW

V3010-1H WS1 INJECTOR ASY H GREEN

V3010-1I WS1 INJECTOR ASY I ORANGE

V3010-1J WS1 INJECTOR ASY J LIGHT BLUE

V3010-1K WS1 INJECTOR ASY K LIGHT GREEN

Not Shown V3170 O-RING 011 *

Not Shown V3171 O-RING 013 *

* The injector plug and the injector each contain one 011 (lower) and 013 (upper) o-ring.

Note: For upﬂow position, injector is located in the up hole and injector plug is in the

other hole. Upﬂow option is not applicable to EA, EE or EI control valves.

For a ﬁlter that only backwashes, injector plugs are located in both holes.

WS1TT Drawings and Service Manual Page 9

Actual tank size used may vary depending on the design and application of the system.

Tank diameter is an approximation for the following:

1. downﬂow softener using standard mesh synthetic cation exchange media regenerating

with sodium chloride.

2. upﬂow softener using standard mesh synthetic cation exchange media regenerating

with sodium chloride, an inlet water pressure of 30 to 50 psi (2.1 to 3.4 bar) and water

temperature of 60°F (15.6°C) water or warmer. Higher pressures or lower temperatures

would need smaller injectors to avoid lifting the bed.

*Not applicable for EA, EE or EI control valves.

Injector Order Information

Typical Tank Diameter

Injector Order Number Injector Color Down

WS1 & WS1.25 Up*

V3010-1A Black 6" 8"

V3010-1B Brown 7" 9"

V3010-1C Violet 8" 10"

V3010-1D Red 9" 12"

V3010-1E White 10" 13"

V3010-1F Blue 12" 14"

V3010-1G Yellow 13" 16"

V3010-1H Green 14" 18"

V3010-1I Orange 16" 21"

V3010-1J Light Blue 18"

V3010-1K Light Green 21"

Page 10 WS1TT Drawings and Service Manual

Table des matières

Autres manuels Water Specialist Unité de contrôle

Water Specialist

Water Specialist WS1HR Manuel utilisateur

Water Specialist

Water Specialist WS1CT Manuel utilisateur

Water Specialist

Water Specialist WS2H Manuel utilisateur

Water Specialist

Water Specialist EE Manuel utilisateur

Water Specialist

Water Specialist CK Manuel utilisateur

Water Specialist

Water Specialist WS2HF Manuel utilisateur

Water Specialist

Water Specialist WS1TC Mode d’emploi

Water Specialist

Water Specialist WS1CC Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur