Wasp WWS500 Mode d'emploi

Wasp Barcode Technologies

1400 10th Street

Plano, TX 75074

www.waspbarcode.com 1007US

WWS500 Programming Guide

Barcode Scanning Made Easy

Table of Contents

Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Chapter 2. Barcode Symbologies . . . . . . . . . . . . . . . . . . .3

Chapter 3. Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Chapter 4. WWS500 Setup & Configuration . . . . . . . .6-28

1. Setup & Configuration . . . . . . . . . . . . . . . . .6

2. Factory Default & Autosense Stand Mode . .7

3. Beep and Delay . . . . . . . . . . . . . . . . . . . .8-9

4. Upper/Lower Case . . . . . . . . . . . . . . . . . . .10

5. Keyboard Language . . . . . . . . . . . . . . . . . .11

6. Preamble/Postamble Configuration . . . . . .12

7. Terminator/Code ID . . . . . . . . . . . . . . . . . .13

Enable/Disable Barcode Symbologies

. . .14-15

9. Barcode Symbology Settings . . . . . . . .16-28

Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Interleaved 2 of 5 and Code 93 . . . . . . . . .17

Code 128 and UCC/EAN 128 . . . . . . . . . . .18

MSI/Plessey . . . . . . . . . . . . . . . . . . . . . . .19

Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . .20

UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

UPC-A Supplemental / UPC-A to EAN-13 .22

UPC-E . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

UPC-E Supplemental . . . . . . . . . . . . . . . . .24

EAN-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

EAN-8 Supplemental . . . . . . . . . . . . . . . . .26

EAN-13 . . . . . . . . . . . . . . . . . . . . . . . . . . .27

EAN-13 Supplemental . . . . . . . . . . . . . . . .28

Chapter 5. Bluetooth Settings . . . . . . . . . . . . . . . . . . . . .29

Appendix A Barcode Test Symbols . . . . . . . . . . . . . . .30-32

Appendix B ASCII Table . . . . . . . . . . . . . . . . . . . . . . . .33-36

Appendix C Codes for PC . . . . . . . . . . . . . . . . . . . . . . . . .37

Appendix D Technical Specifications . . . . . . . . . . . . . . . . .38

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

FAQ / Product Support . . . . . . . . . . . . . . . . .40

Chapter 1

Introduction

Barcoding is the most common Automated Data Collection (ADC)

technology providing timely, error-free information that can be used to

increase productivity, accuracy, and efficiency in the workplace. Virtually

every type of industry is using bar codes to replace keyboard data entry.

Studies have shown that a proficient data entry operator will make one

error for every 300 characters that are manually entered. The error rate

using barcodes is almost negligible and can be error-free using barcode

symbologies with the check digit enabled.

The Wasp Charged Coupled Device (CCD) technology is a technique

whereby a barcode is photographed, digitized, and electronically sampled

by built-in photodetectors. The detectors process the measurement of

every bar and space using the number of adjacent photodetectors which

contrast a black mark and a white space. The Wasp WWS500 Freedom

Scanner is extremely rugged since it has no moving parts.

Of all the hand held barcode scanning devices on the market, the CCD

reader is the easiest to use and most cost effective for the typical business

user. The Wasp WWS500 Freedom Scanner is an extended distance

scanner with a depth of reading of up to one foot depending on the mil

size of the barcode. To activate the scanner, the user simply points the

scanning aperture towards the barcode, pulls the trigger, and aims the red

LED beam across the barcode.

Chapter 2

Barcodes are symbols consisting of a series of bars and spaces which can

be applied to packages, cartons, bottles, and other commercial products.

The bars and spaces in each symbol are grouped in such a way to

represent a specific ASCII character or function. The interpretation of

these groups is based on a particular set of rules called symbologies.

Various symbologies have been developed for particular applications.

Some examples are shipping and receiving, manufacturing, retail,

healthcare, transportation, document processing and tracking, and

libraries.

The resolution of a barcode is dependent on the narrowest element of a

barcode (X dimension), and can vary from high density (nominally less

than 0.009 in./0.23 mm), medium density (between 0.009 in./0.23 mm and

0.020 in./0.50 mm), and low density (greater than 0.020 in./0.50 mm).

Medium and low densities are the most common since these are the

easiest to read (scan) with nearly all scanning devices. The Wasp

WWS500 Freedom Scanner can read barcodes with X-dimensions as low

as 5 mils (0.005 in/0.13mm).

The Wasp WWS500 Freedom Scanner can read the most popular barcode

symbologies including Code 39, Code 93, Code 128, Interleaved 2 of 5,

UPC-A, UPC-E, EAN/JAN-8, EAN/JAN-13, Codabar, and MSI/Plessey.

Please see test chart on pages 28-30.

Barcode Symbologies

Chapter 3

Quick Start

1. Unpack

Open the box and remove all the pieces from their protective packaging.

2. Charging the WWS500

You must charge the scanner for 4 hours before first using it. To charge

the scanner plug the power supply in to the bottom of the scanner.

3. Setting up the Bluetooth Adaptor

If you already have Bluetooth setup on your PC or device, please

continue to the next step.

To setup Bluetooth on your PC you will need to insert the Bluetooth

adapter into an available USB port. Windows will detect the adapter and

install the required Microsoft Bluetooth software. If Windows does not

detect the Bluetooth adapter, please remove the adapter and insert the CD

with the adapter’s Bluetooth software on it. Follow the instruction on the

CD for installing the Bluetooth software.

4. Connecting the scanner to a Bluetooth device.

The scanner will connect to most Bluetooth devices that support HID

connection.

You will need to open your Bluetooth software and search for Bluetooth

devices. The Bluetooth software can be found by clicking the Bluetooth

symbol on the start bar near the computer time. If the Bluetooth symbol is

not found, there could be a problem with the Bluetooth adapter installation.

Once you have the Bluetooth software open

you will need to scan the Set Connection

barcode (right). This will make the scanner ready

to be detected by the Bluetooth software. Set Connection

Chapter 3

The following screens are Microsoft’s standard Bluetooth wizard.

*Most Bluetooth wizards will have similar steps.



Check the “My device is setup and

ready to be found.” and click Next.

The scanner will show up in the list of

Bluetooth devices found. Select the

WASP_HID and click Next.

* If WASP_HID does not show up in the

available devices please check the following.

- Make sure the scanner is on by pressing

the trigger.

- If you are using a pre-installed Bluetooth

adapter, make sure the adapter supports HID.

The next step will ask you to setup a passkey

for the device. By default the scanner will not

have a passkey set. Please select “Don’t use

a passkey” and click Next.

The last screen of the wizard will be complete

the wizard. Just click Finish to complete.

Once the wizard is complete the scanner will

show up as a WASP_HID Device. Click OK to

close the screen. You are now ready to use

the WWS500.



Chapter 4

In order to configure Wasp WWS500 Freedom Scanner, you must

familiarize yourself with the setup procedures on the following pages. The

default settings of the scanners are identified on each page and clearly

marked using an asterisk (*). The default settings have been

preprogrammed for the most common barcode configurations.

Use the setup & configuration barcodes only to customize the

WWS500 Freedom Scanner settings. If you need to configure the

Scanner, the default settings will be overwritten. All the programmed

settings are stored permanently in non-volatile memory.

In order to configure Wasp WWS500 Freedom Scanner,

two basic steps need to be followed:

(1) Locate the group that contains the options to be changed.

(2) Scan the barcode representing the option to be changed.

The scanner will sound two beeps.

To change Minimum/Maximum Length:

(1) Scan the Minimum or Maximum Length barcode on page 15.

(2) Scan a 2 digit value from the ASCII table on pages 31-34

(3) Scan the Minimum or Maximum Length barcode again.

Example: To have a minimum length barcode of 1, you must scan a

0 then 1, then scan the minimum barcode again. To have a maximum

length barcode of 10, you must scan a 1 then 0, then scan the

maximum barcode again.

Setup & Configuration

Chapter 4

FACTORY DEFAULT & KEYBOARD CONNECTION

Use the Factory Default barcode to reset the scanner to the Default settings.

Factory Default

Autosense Flash Mode Enable

Scan this Autosense Stand Mode bar code to enable the hands-free autosense

feature of the WWS500 Freedom Scanner. If you desire to turn this mode “off,”

please scan the default bar code above.

Autosense Stand Mode

Factory Default

Note: Enabling this option will significantly increase the WWS500

Freedom Scanners battery consumption.

Chapter 4

BEEP AND DELAY

The 'Beep and Delay' configuration supports the general control options for the

Wasp WWS500 Freedom Scanner. These options include the volume,

intercharacter delay, and interblock delay.

Interblock delay is the minimum time interval between two adjacent scans. If the

processing speed of your host device is slower than your scanning speed, a longer

interblock delay may ensure the data integrity.

Intercharacter delay is the time period that the scanner will wait before transmitting

the next character. If data sent by the scanner has incorrect or missing characters,

a longer intercharacter delay may solve the problem. The intercharacter delay

should be changed only if the transfer rate cannot be maintained between the

scanner and the keyboard buffer of the computer.

Note: The default for the intercharacter delay is set to '140us' and is the most

common configuration; however, your PC may be different. When you scan a bar

code, if some stray or scrambled characters appear, increase the intercharacter

delay to slow down the transfer rate.

Beep Off

Beep Medium *

Beep High to Low

Beep Hi

Beep Low to High

Beep Low

Beep Settings

*Default

Chapter 4

BEEP AND DELAY

0ms *

10ms

50ms

100ms

200ms

140us *

500us

1ms

4ms

16ms

500ms

Interblock Delay Intercharacter Delay

*Default

Autres manuels pour WWS500

Table des matières

Autres manuels Wasp Lecteur de codes-barres

Wasp

Wasp WLS 9500 Manuel utilisateur

Wasp

Wasp WDI4500 Manuel utilisateur

Wasp

Wasp CCD Scanner Mode d'emploi

Wasp

Wasp WWS650 Manuel d'installation et d'exploitation

Wasp

Wasp WWS650 Guide de l'administrateur

Wasp

Wasp WPL610 Manuel utilisateur

Wasp

Wasp N1181 Mode d'emploi

Wasp

Wasp WLR8950 Manuel utilisateur

Wasp

Wasp WWS450 Manuel utilisateur

Wasp

Wasp WPL608 Manuel utilisateur

Wasp

Wasp WLS9600 Manuel utilisateur

Wasp

Wasp WLS 9500 Manuel utilisateur

Wasp

Wasp HC1 Manuel utilisateur

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WDI4500 Manuel utilisateur

Wasp

Wasp WWS110i Manuel utilisateur

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WLR8950 Manuel utilisateur

Wasp

Wasp WDT 3200 Manuel d'installation et d'exploitation

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WWS550SBR Manuel utilisateur

Wasp

Wasp WWS750 Manuel utilisateur

Wasp

Wasp WWS110i Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur