Wasp HC1 Manuel utilisateur

Wasp HC1

No part ofthis publication may be reproduced or used in any form, or by any electrical or mechanical means, without

permission in writing from Wasp Technologies. This includes electronic or mechanical means, such as photocopying,

recording, or information storage and retrievalsystems. The material in this manual is subject to change without notice.

The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed

basis. Wasp Technologies grants to the user a non-transferable and nonexclusive license to use each software or firmware

program delivered hereunder (licensed program). Except as noted below,such license may not be assigned, sublicensed, or

otherwise transferred by the user withoutprior written consent of Wasp Technologies. No right to copy a licensed program in

wholeor in part is granted,except as permitted undercopyright law. Theuser shallnotmodify,merge, or incorporateany form

or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a

licensed program in a networkwithout written permission from Wasp Technologies. The user agrees to maintain Wasp

Technologies’ copyright notice on the licensed programs delivered hereunderand to include thesameon any authorized copies

it makes, in whole or in part. The user agrees notto decompile, disassemble, decode,or reverseengineer any licensed program

delivered to the user or any portion thereof.

Wasp Technologies reserves the right to make changes to any software or product to improve reliability, function, or design.

Wasp Technologies does not assume any product liability arising out of, or in connection with, the application or use of any

product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or

otherwise under any Wasp Technologies, intellectual property rights. An implied license only exists for equipment, circuits,

and subsystems contained in Wasp Technologies products.

Wasp Technologies is a registered trademark of Wasp Technologies. Other product namesmentioned in this manual may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

Wasp Technologies

1400 10th St.

Plano TX 75074

http://www.waspbarcode.com

Rev. 4/12/2012

Wasp HC1 User Manual

Table of Contents

Table of Contents .................................................................................................................i

Regulatory Compliance Information .................................................................................iv

FCC Warning Statement................................................................................................iv

FCC Label Statement....................................................................................................iv

RF Radiation Exposure Statement..................................................................................v

Canadian Compliance Statement...................................................................................v

European Conformity Statement.....................................................................................v

RoHS Statement............................................................................................................v

Tiawan NCC Warning Statement....................................................................................v

Laser Information..........................................................................................................vi

Battery Notices..............................................................................................................vi

Battery Charge Notice.................................................................................................. vii

Storage and Safety Notice............................................................................................viii

Warranty......................................................................................................................viii

Chapter 1 - Getting Started .................................................................................................1

1.1Introducing the Wasp HC1 ....................................................................................1

1.2 Features...................................................................................................................2

1.3 HC1 Product Introduction & Accessory Kit ................................................................3

1.4 Tour of the HC1........................................................................................................4

1.4.1 HC1 Front and Right View............................................................................4

1.4.2 HC1 Rear and Left View...............................................................................5

1.5 Turning on the HC1 for the First Time.......................................................................6

1.6 Installing the Battery.................................................................................................6

Battery Compartment Tab.................................................................................................6

Wasp HC1 User Manual

1.7 Charging the Battery ................................................................................................8

1.8 Checking the LED status..........................................................................................9

1.9 Checking the Battery Status .....................................................................................9

1.10 Keypads and Functions........................................................................................10

1.11 Using the Function Keys.......................................................................................11

1.12 Using Alpha Keys.................................................................................................12

Chapter 2 – Using the Hardware.......................................................................................13

2.1 Using the MicroSD Memory Card ...........................................................................13

2.1.1 Inserting a Memory Card............................................................................13

2.1.2 Removing the Memory Card.......................................................................13

2.2 Using the SIM Card................................................................................................14

2.3 Using the Barcode Laser Scanner..........................................................................15

Chapter 3 – Getting Connected ........................................................................................17

3.1 Establishing Device – PC Connection.....................................................................17

3.1.1 Installing Microsoft ActiveSync (XP Users Only)..........................................17

3.1.2 Connectingthe Device to Your Computer...................................................18

3.2 WIFI Connection ....................................................................................................19

3.2.1 Using the Summit Utilities...........................................................................19

3.3 u-Center Mobile for Quick GPS Connection............................................................22

3.3.1 To Open u-Center Mobile ...........................................................................23

3.3.2 To Download Data......................................................................................23

Chapter 4 – Barcode Scanner Programs..........................................................................25

4.1 Scanner Settings....................................................................................................25

4.2 Scan2Key ..............................................................................................................25

4.3 Barcode Symbologies.............................................................................................26

4.4 Barcode Symbologies 2D.......................................................................................27

iii

Wasp HC1 User Manual

Chapter 5 – Advanced Settings ........................................................................................28

5.1 Performing a Hardware Reset ................................................................................28

5.1.1 Performing a Warm Boot............................................................................28

5.1.2 Performing a Cold Boot..............................................................................28

System Specifications.......................................................................................................30

Support..............................................................................................................................32

Wasp HC1 User Manual

Regulatory Compliance Information

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference with radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

with radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

–Consult the dealer or an experienced radio/TV technician for help.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact

to the transmitting antenna during transmitting.

3. Any changes or modifications (including the antennas) made to this device that are not expressly

approved by the manufacturer may void the user’s authority to operate the equipment.

FCC Label Statement

This device complies with part 15 ofthe FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

Wasp HC1 User Manual

RF Radiation Exposure Statement

For body contact during operation, this phone has been tested and meets FCC RF exposure

guidelines when used with an accessory that contains no metal and that positions the handset a

minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF

exposure guidelines.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur

du Canada.

European Conformity Statement

Declaration of Conformity with regards to the R&TTE 1999/5/EC and EMC 89/336/ EEC directives.

RoHS Statement

This device conforms to RoHS (Reduction Of Hazardous Substances) European Union regulations

that set maximum concentration limits on hazardous materials used in electrical and electronic

equipment.

Tiawan NCC Warning Statement

交通部電信總局低功率電波輻射性電機管理辦法 (930322)

根據交通部低功率管理辦法規定：

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得

擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現

象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依

電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之

干擾。

Wasp HC1 User Manual

Laser Information

The Wasp HC1 series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR

Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered

to be hazardous. The HC1 series contains internally a Visible Laser Diode (VLD) whose emissions do

not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that

there is no human access to harmful laser light during normal operation, user maintenance or

prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the HC1 series' optional laser scanner

module is located on the memory compartment cover, on the back of the unit.

Caution: Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous laser light. Use of optical instruments with the scanner, including

binoculars, microscopes, and magnifying glasses, with will increase eye damage.This does not include

eyeglasses worn by the user.

Battery Notices

The HC1 is equipped with a Lithium-Ion battery pack and a Ni-Mh backup battery. Both batteries will

discharge after an extended period of no use.

When both batteries are discharged, recharge the unit for 12 hours in order to fully charge the main

battery and backup battery. Recharge the HC1 battery by doing the following:

1. Plug the USB charging cable into the HC1 and plug the 5V/3A AC-DC adapter into the power

jack of the USB charging cable.

2. Place the HC1 into the docking station and plug the 5V/3A AC-DC adapter into the power jack

of the docking station.

vii

Wasp HC1 User Manual

If the main battery is removed, the backup battery ensures the data on SDRAM is safe for up to 2 hours.

To prevent data loss, do not leave the HC1 uncharged with the main battery removed for an extended

period. See the Charging the Battery unit on for more details.

Note: To guarantee optimal performance, it is advised that rechargeable batteries be replaced every

year, or when 500 charge/discharge cycles are achieved. It is normal that the battery balloons

or expands beyond one year or the maximum of 500 cycles. Although it does not cause harm, it

cannot be used again and must be disposed of according to the location's safe battery disposal

procedures.

If the performance decrease is greater than 20% in a Lithium-Ion battery, the battery is at the

end of its life cycle. Do not continue to use, and ensure the battery is disposed of properly.

The length of time that a battery lasts depends on the battery type and how the device is used.

Conserve the battery life by doing the following:

Avoid frequent full discharges because this places additional strain on the battery. Several partial

discharges with frequent recharges are better than a full discharge. Recharging a partially

charged lithium-Ion battery does not cause harm because there is no memory.

Keep the lithium-Ion battery cool. Avoid a hot car. For prolonged storage, keep the battery at a

40% charge level.

Do not leave the lithium-Ion battery discharged and unused for an extended period because the

battery will wear out and the longevity of the battery will be at least half of the one with frequent

recharges.

Battery Charge Notice

It is important to consider the environment temperature when the Lithium-Ion battery pack is charged.

Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential

that batteries are charged within the stated range of 0°C to 40°C. Charging batteries outside of the

specified range could damage the batteries and shorten their charging life cycle.

Caution: Do not charge batteries at a temperature lower than 0°C. This will increase the internal

resistance to cause heat and make the batteries unstable and unsafe. Please use a battery

temperature detecting device for a charger to ensure a safe charging temperature range.

viii

Wasp HC1 User Manual

Storage and Safety Notice

Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be

depleted due to buildup of internal resistance. If this happens they will require recharging prior to use.

Lithium-Ion batteries may be stored at temperatures between -20°C to 60°C, however they may

deplete more rapidly at higher temperatures. It is recommended to store batteries at room

temperature.

Warranty

The following items covered under the Limited Warranty are free from defects during normal use:

Wasp HC1 – 1-year limited warranty.

Lithium-Ion battery – 6-month limited warranty.

Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or

neglect, or if any parts are improperly installed or replaced by the user.

Use only the adapter supplied. Using the wrong adapter may damage the unit and will void the

warranty.

Autres manuels pour HC1

Table des matières

Autres manuels Wasp Lecteur de codes-barres

Wasp

Wasp WPS1500 Manuel utilisateur

Wasp

Wasp WLS 9500 Manuel utilisateur

Wasp

Wasp Wasp WDI7500 Manuel d'installation et d'exploitation

Wasp

Wasp CCD Scanner Mode d'emploi

Wasp

Wasp WPL608 Manuel utilisateur

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WPA 1200 II Manuel utilisateur

Wasp

Wasp WDI4500 Manuel utilisateur

Wasp

Wasp CCD - 80SIR Manuel utilisateur

Wasp

Wasp 2D Manuel utilisateur

Wasp

Wasp WWS450 Manuel utilisateur

Wasp

Wasp WDT 3200 Manuel d'installation et d'exploitation

Wasp

Wasp WWS150i Manuel utilisateur

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WLS8600 Manuel utilisateur

Wasp

Wasp WWS800 Manuel utilisateur

Wasp

Wasp WLR8950 Manuel utilisateur

Wasp

Wasp WWS550i Manuel utilisateur

Wasp

Wasp WLS 9500 Manuel utilisateur

Wasp

Wasp 2D Manuel utilisateur

Wasp

Wasp WWS500 Mode d'emploi

Wasp

Wasp WWS150i Manuel utilisateur

Wasp

Wasp WWS110i Manuel utilisateur

Wasp

Wasp WLS8600 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur