Waring BB155 SERIES Manuel utilisateur

BB155/BB155S SERIES

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

DE LAS LICUADORAS

DE LA SERIE BB155/BB155S

DIRECTIVES D’UTILISATION

DES MÉLANGEURS

DE LA SÉRIE BB155/BB155S

For your safety and continued enjoyment of this product,

always read the instruction book carefully before using.

Para su seguridad y para disfrutar plenamente de este producto,

siempre lea las instrucciones cuidadosamente antes de usarlo.

An que votre appareil vous procure en toute sécurité beaucoup de

satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions

should always be followed, including the following:

1. READ ALL INSTRUCTIONS.

2. Unplug from outlet when not in use, before putting

on or taking off parts, and before cleaning.

3. To protect against electrical hazards, do not immerse

the blender base in water or other liquids.

4. This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

5. Children should be supervised to ensure that they

do not play with the appliance.

6. Avoid contact with moving parts.

7. Do not operate any appliance with a damaged cord or

plug or after the appliance malfunctions or is dropped

or damaged in any manner. Return appliance to the

nearest authorized service facility for examination,

repair or electrical or mechanical adjustment.

8. The use of attachments, including canning jars, not

recommended by the appliance manufacturer may

cause hazards.

9. Do not use outdoors.

10. Do not let cord hang over edge of table or counter,

where it can inadvertently be pulled on or tripped over,

or touch hot surfaces, which could damage the cord.

11. Keep hands and utensils out of container while

blending, to prevent the possibility of severe personal

injury and/or damage to the blender. A rubber scraper

may be used, but must be used only when the blender

is not running.

12. Blades are SHARP. Handle carefully.

13. Never place cutting assembly or cutting blades on base

without container properly attached.

14. Always operate blender with cover in place.

15. Always operate blender with jar pad in place.

16. CAUTION:This blender is not intended for use with hot

liquids or ingredients.

17. Do not ll above MAX FILL line for blending.

18. Not for waterjet cleaning.

19. Ensure the jar coupler and motor coupler are aligned

and engaged before operating. If unable to engage,

remove jar and shake contents, then try again.

20. The jar coupler and motor coupler may be hot after

running; do not touch.

21. Always use HIGH speed for crushing ice.

22. If the jar overows during blending, there is too much

liquid/ingredients in the jar. Stop blending, remove

enough liquid/ingredients to below MAX FILL line, and

continue blending. Do not operate if overowing.

23. DO NOT use carbonated liquids in the blender jar or

any blending container. Using carbonated liquids in

the blender jar or any blending container may result in

injury.

24. DO NOT blend oil or oil-based products such as peanut

butter for greater than 5 minutes.

25. Never remove blender jar from base unit until the blade

and coupling have completely stopped.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

• For your protection, Waring®Commercial Blenders are

equipped with a 3-conductor cord set.

• 120 volt units are supplied with a molded 3-prong

grounding-type plug and should be used in combination

with a properly connected grounding-type outlet, as

shown in Figure 1.

If a grounding-type outlet is not available, an adapter, shown

in Figure 2, may be obtained to enable a 2-slot wall outlet to

be used with a 3-prong plug.

Referring to Figure 3, the adapter must be grounded by

attaching its grounding lug under the screw of the outlet

cover plate.

CAUTION: Before using an adapter, it must be determined

that the outlet cover plate screw is properly grounded. If in

doubt, consult a licensed electrician.

Never use an adapter unless you are sure it is properly

grounded.

NOTE: Use of an adapter is not permitted in Canada.

BLENDER JAR ASSEMBLY INSTRUCTIONS

1. When assembling blade

assembly to jar, beware of the

blades as they are very sharp.

2. Position rubber seal over blade

assembly so that it sits in

between the ats of the blade

assembly and the jar.

3. Insert blade assembly with

rubber seal into the bottom hole

of the jar.

NOTE: To avoid leaking while

blending, be sure the rubber

seal is positioned in between the

blade assembly and the jar. HINT:

Assembling the jar is easier when

the bottom of the jar is facing up.

4. Screw the collar clockwise onto

the jar until it tightly secures the

blade assembly and seal to the jar.

BB155 OPERATION

1. Before starting, make sure

that the blender is unplugged.

2. Always be sure container is properly assembled before

adding ingredients.

3. Put ingredients into container and cover it. Do not ll

above MAX FILL line.

4. With the switch in the OFF position,

place container on blender base. Be

sure container is fully seated and that

drive coupling is properly engaged.

Plug blender cord into outlet.

5. This blender has 2 speed settings:

HI and LO. Press toggle switch to desired position. To

crush ice, always use HI speed setting.

6. When nished blending, set toggle switch to OFF

position.

7. Allow motor to come to a complete stop before

removing container from blender base. Never place

the container on the motor base or remove it from

the motor base while motor is running.

8. Always hold container with one hand when starting and

while blending. Never operate without jar lid.

9. Wash and dry container after each use. See Cleaning

and Sanitizing Instructions.

10. Unplug to turn off all power to blender.

CLEANING AND SANITIZING INSTRUCTIONS

THE CONTAINER MUST BE CLEANED AND DRIED AFTER

EACH USE OF THE BLENDER ACCORDING TO THE

FOLLOWING INSTRUCTIONS.

FAILURE TO DO SO MAY ALLOW RESIDUE OF

PROCESSED MATERIAL TO COLLECT ON THE INTERNAL

SEALS OF THE BLADE ASSEMBLY, RENDERING THEM

INEFFECTIVE.

• Wash, rinse, sanitize and dry container prior to initial use

and whenever it will not be used again within a period of

1 hour.

• Wash and rinse container and blade assembly after

each use.

• Clean and sanitize motor base prior to initial use and after

each use.

• Washing solutions based on non-sudsing detergents and

chlorine-based sanitizing solutions having a minimum

chlorine concentration of 100 PPM are recommended.

The following washing, rinsing, and sanitizing solutions, or

their equivalents, may be used.

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE

Washing Diversey®Wyandotte 4 Tablespoons Hot 115˚F (46˚C)

Diversol®BX/A or CX/A /Gallon

Rinsing Plain Water Warm 95˚F (35˚C)

Sanitizing Clorox®1 Tablespoon/Gallon Cold 50˚F–70˚F

Institutional Bleach (10˚C–21˚C)

• In repetitive batch-processing applications, frequent

cleaning of the container will prolong the life of the blade

assembly. In no case should actual running time between

cleanings exceed one-half hour.

• Do not use container to store processed foods or

beverages.

TO WASH AND RINSE CONTAINER

1. REMOVE CONTAINER FROM MOTOR BASE.

Remove lid. Rinse container interior and lid under

running water. Add washing solution to container.

Scrub and ush out the container interior and lid to

dislodge and remove as much food residue as

possible. Empty container.

2. Wipe down exterior of container with a soft cloth or

sponge dampened with washing solution. Wash lid

and lid insert in fresh washing solution. Fill container

one-quarter full with fresh washing solution, cover

(with lid only), place on motor base and run on HIGH

speed for two (2) minutes. Empty container.

3. Repeat step (2) using clean rinse water in place of

washing solution.

IMPORTANT

NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF

SCALDING, TEMPERATURE OF WASHING SOLUTION

AND RINSE WATER MUST NOT EXCEED 115˚F (46˚C), AND

QUANTITY USED MUST NOT EXCEED ONE-QUARTER

CONTAINER FULL.

TO SANITIZE AND DRY CONTAINER

1. Wipe down exterior of container with a soft cloth

or sponge dampened with sanitizing solution.

2. Fill container with sanitizing solution, cover, place on

motor base, and run on HIGH speed for one (1) minute.

Empty container. Dislodge any residual moisture from

blade assembly by placing empty container on motor

base and running on HIGH speed for two (2) seconds.

3. Sanitize lid and lid insert by immersing in sanitizing

solution for two (2) minutes.

4. Do not rinse container, lid, or lid insert after sanitizing

is completed. Allow parts to air-dry.

TO CLEAN AND SANITIZE MOTOR BASE

1. UNPLUG POWER CORD. Wipe down exterior surfaces

of motor base with soft cloths or sponges dampened

with washing solution, rinse water, and sanitizing

solution. Prevent liquid from running into motor base

by wringing all excess moisture from cloths or sponges

before using them.

DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION,

RINSE WATER OR SANITIZING SOLUTION.

2. Allow motor base to air-dry before using.

SERVICE

Refer to the list of Authorized Service Centers enclosed

with your Waring®Commercial Blender for the name of the

nearest Service Center, or write to:

Waring Factory Service Center

P.O. Box 3201

314 Ella T. Grasso Avenue

Torrington, CT 06790

1-800-492-7464

Ship blenders for repair to the above address or to an

Authorized Service Center. Do not ship to a Waring Sales

Ofce.

NOTE: If your application involves the processing of

biologically active material, we request that any items

returned for service be sterilized before being shipped.

Such items must be clearly identied as having been

sterilized, both by a tag on the item itself and by a statement

in the accompanying correspondence. Waring will not

accept delivery of any return unless it is so identied.

Replacement parts for your out-of-warranty repairs are

obtainable at the address below.

LIMITED TWO YEAR WARRANTY

Waring warrants every new Waring®Commercial Blender

to be free from defects in material and workmanship for a

period of two years from the date of purchase when used

with foodstuffs, nonabrasive liquids (other than detergents)

and nonabrasive semi-liquids, providing it has not been

subject to loads in excess of the indicated rating. In addition,

the motor in this appliance has a full three year warranty.

Under this warranty, Waring will repair or replace any part

that, upon our examination, is defective in materials or

workmanship, provided the product is delivered prepaid

to the Waring Service Center at: 314 Ella T. Grasso Ave.,

Torrington, CT 06790, or any Authorized Service Center.

This warranty does not: a) apply to any product that has

become worn, defective, damaged or broken due to misuse

or due to repairs or servicing by other than the Waring

Service Center or an Authorized Service Center, or due

to abuse, misuse, overloading or tampering; or b) cover

incidental or consequential damages of any kind.

The one year warranty is applicable only to appliances

used in the United States or Canada; this supersedes all

other express product warranties or warranty statements.

For Waring products sold outside of the U.S. and Canada,

the warranty is the responsibility of the local importer

or distributor. This warranty may vary according to local

regulations.

Warning: This warranty is void if appliance is used on

Direct Current (DC).

Waring Commercial

314 Ella T. Grasso Avenue

Torrington, CT 06790

1-800-4-WARING

www.waringcommercialproducts.com

Autres manuels pour BB155 SERIES

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Waring Mixer

Waring

Waring BB185 Manuel utilisateur

Waring

Waring TBB160 Manuel utilisateur

Waring

Waring BOLT WSB38X Manuel utilisateur

Waring

Waring RB70 Manuel utilisateur

Waring

Waring Xtreme MX1000XTX Manuel utilisateur

Waring

Waring MX1000XT Manuel utilisateur

Waring

Waring BB185 Manuel utilisateur

Waring

Waring BIG STIX WSB50 Manuel utilisateur

Waring

Waring wsb33x Manuel utilisateur

Waring

Waring WSB40 Manuel utilisateur

Waring

Waring PRO MEGAMIX HPB300 Guide rapide

Waring

Waring Blender Manuel utilisateur

Waring

Waring BB300 Manuel utilisateur

Waring

Waring BB320 Manuel utilisateur

Waring

Waring Torq 2.0 TBB160 Manuel utilisateur

Waring

Waring QUIK STIK PLUS WSB40 Manuel utilisateur

Waring

Waring CB15 SERIES Manuel utilisateur

Waring

Waring Torq 2.0 TBB175S6 Manuel utilisateur

Waring

Waring BB155 SERIES Manuel utilisateur

Waring

Waring 700G Manuel utilisateur

Waring

Waring BIG STIX WSB50 Manuel utilisateur

Waring

Waring MBB Manuel utilisateur

Waring

Waring QUIK STIK PLUS WSB40E Manuel utilisateur

Waring

Waring HPB305 Manuel utilisateur

Manuels Mixer populaires d'autres marques

ROTOR

ROTOR 1125.201 Manuel utilisateur

Braun

Braun Multiquick 5 Vario series Manuel utilisateur

ARENDO

ARENDO MIRA 305424 Manuel utilisateur

CHEF-BUILT

CHEF-BUILT CCB-3500 Manuel utilisateur

Viconte

Viconte VC-4406 Manuel utilisateur

Oster

Oster BLSTAB-CB0 Manuel utilisateur

HOFFEN

HOFFEN MC-3005 Manuel utilisateur

Black & Decker

Black & Decker BLC18750DM Manuel utilisateur

Sunbeam

Sunbeam 4182 Manuel utilisateur

Bialetti

Bialetti FMX35 Manuel utilisateur

Black & Decker

Black & Decker BL8000 Manuel utilisateur

Duronic

Duronic BL530 Manuel utilisateur

Exquisit

Exquisit MS 3002 wes Manuel utilisateur

Lumme

Lumme LU-KP1891A Manuel utilisateur

Binatone

Binatone HB-735 Manuel utilisateur

Moulinex

Moulinex LM936E10 Manuel utilisateur

Oster

Oster VERSA Manuel d'installation et d'exploitation

Ninja

Ninja NN210Q Manuel utilisateur