VORON 2.4 Manuel utilisateur
VORON 2.4
KIT 3
∙Z DRIVE
WWW.VORONDESIGN.COM
INTRODUCTION
Before you begin on your journey, a word of caution.
In the comfort of your own home you are about to assemble a robot. This
machine can maim, burn, and electrocute you if you are not careful. Please
do not become the rst VORON fatality. There is no special Reddit air for that.
Please, read the entire manual before you start assembly. As you begin wrenching,
please check our Discord channels for any tips and questions that may halt your progress.
Most of all, good luck!
THE VORON TEAM
01
WWW.VORONDESIGN.COM
https://voron.link/m5ybt4d
HEAT SET INSERTS
This design relies heavily on heat
set inserts. Make sure you have the
proper inserts (check the hardware
reference for a close up picture and
the BOM for dimensions).
If you’ve never worked with heat set
inserts before we recommend you
watch the linked guide.
Heat Set Insert
PREPARATION
02
WWW.VORONDESIGN.COM
SET SCREWS
aka the root of all issues
Insert both set screws and use thread
locker on all set screws.
Use a high quality hex driver to prevent
the hex prole from stripping. Ball-end
drivers are not recommended.
Loose set screws account for the majority
of issues that our users report. Save
yourself hours of troubleshooting and
apply thread locker to all set screws
during the build.
See the products application notes for
instructions - keep away from printed
parts.
GT2 20T 9mm wide Pulley
5x60 Shaft
POSITION AS SHOWN
Make sure one of the set screws is
oriented with the D cut, as shown in
the image.
BELT DRIVE ASSEMBLY
03
WWW.VORONDESIGN.COM
625 Bearing
GT2 80 Tooth Pulley
625 Bearing
625 Bearing
CHECK YOUR WORK
Compare your assembled parts to
the graphics shown here.
BELT DRIVE ASSEMBLY
APPLY THREAD LOCKER
Make sure to use thread locker on the
set screws.
M5 Shim
04
WWW.VORONDESIGN.COM
GT2 188mm Belt Loop
Z DRIVE
05
WWW.VORONDESIGN.COM
CHECK SHAFT POSITION
Compare your assembled parts to
the graphics shown here.
Z DRIVE
06
WWW.VORONDESIGN.COM
M3x40 SHCS
Z DRIVE
07
WWW.VORONDESIGN.COM
WHERE’S THAT PRINTED PART?
Look for Voron heart next to the part.
It indicates that this is an accent part.
M5 Nut M3x8 SHCS
Z DRIVE
CHECK FOR BELT
Make sure the closed belt loop is in
the part.
08
WWW.VORONDESIGN.COM
GT2 16 Tooth Pulley
NEMA17 Stepper Motor
16 TOOTH PULLEYS
The Z drive motors are the only
place in the printer that use 16 tooth
pulleys!
Remove them from your work surface
after you nish this chapter.
PULLEY POSITION
Depending on your motors,
you may nd that the pulley
sits better in the opposite
orientation. The important
thing is the placement of the
actual teeth.
Z DRIVE
APPLY THREAD LOCKER
Make sure to use thread locker on the
set screws.
https://voron.link/fx10m8e
Autres manuels pour 2.4
2
Table des matières
Autres manuels VORON Imprimante 3D
VORON
VORON SWITCHWIRE Manuel utilisateur
VORON
VORON STEALTHBURNER Manuel utilisateur
VORON
VORON 2 Manuel utilisateur
VORON
VORON TAP Manuel utilisateur
VORON
VORON ZERO Manuel utilisateur
VORON
VORON CopyMaster3D Manuel utilisateur
VORON
VORON SWITCHWIRE Manuel utilisateur
VORON
VORON ERCF v2 Manuel utilisateur
VORON
VORON 2 Manuel utilisateur
VORON
VORON 2.4 KIT 5 Manuel utilisateur
