Vivotek IP816A-LPC-v2 Manuel utilisateur
IP Surveillance
Installation Guide
IP816A-LPC-v2
License Plate Capturing Solution
Highway & Street
Rev. 1.0
Ordering part no.:
IP816A-LPC-v2 (Highway): 199002900G
IP816A-LPC-v2 (Street): 199002800G
Document part no.: 625041100G
2
Specications
I
Model Number LPC enclosure
Power Input 24V AC
Max. Output power budget 48W (Street); 80W (Highway)
Power Consumption Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W
Environmental Operation Temp. -20°C ~ +50°C (-4°F ~ +149°F)
Protection Level IP68, IK10
Mounting Bracket Fully-cable Management
Construction Die-cast Aluminum Alloy
Coating White epoxy powder coating
Dimensions 502.8 (L) x 170 (W) x 400 (H) mm
Net Weight 6,482g (9.24 lb)
CAUTION:
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears damaged in shipment, place it properly in its carton and
notify the shipper.
IMPORTANT!:
1. Read and follow Instructions: All operating and user instructions should be read and
followed before the unit is to be operated.
2. Electrical Connections: Only a qualied electrician is allowed to make electrical
connections.
3
English
Mounting Conguration & Dimensions
II
Swivel Positions and Directions
105 mm
502.8 mm
135.5 mm
158.5 mm
170 mm
400 mm
77.4 mm
USABLE
AREA
255 mm
USABLE AREA
400
170 502.8
4
Installation Suggestions
IV
If you plan to install this camera enclosure into a tropical, sea coastal, or an environment
where salt water or corrosive industrial waste water/moist are present, please seal each
stainless steel screws and ttings with a silicon grease compounds. This will help prevent
electrolysis to occur and extend the life span of the camera and housing.
IMPORTANT:
1. Disconnect devices: A readily accessible disconnect device in the building installation wiring
should be incorporated.
2. Electrical Connection: Only a qualied electrician is allowed to make electrical connections.
Component Description
III
Camera Mounting Platform
M16 1/2" Waterproof cable gland
Power distribution
board
Ventilation fan Window frame heater
coil
• Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared
protection glasses, when working with the product. Always use camera live view to oberve IR
lighting effects.
WARNING:
5
English
Installation
V
1. Install the wall-mount bracket to a preferred location at your installation site. Drill
mounting holes and a cable routing hole (if preferred) on a wall. Install the bracket.
Prepare and route the wiring, Ethernet and 24V power source.
2. Install the IR illuminator to the bottom of the housing. Attach the included grip stricker
to the U bracket.
6
3. Secure the U bracket to the IR illuminator using the included wrench and hex screws.
4. Flip the housing over and place it on a clean, stable surface. Secure the IR illuminator
to the bottom of the housing using the included wrench and a hex socket screw.
7
English
6. Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through
the M16 waterproof connectors under the housing.
Ethernet cable Ø4 ~ 6.5mm
Power wires & DI/DO wires,
a combo cable from IR illuminator
5. You can turn the IR illuminator so that its at side is parallel with the housing, and that
you can turn the assembly over and work on the inside of the housing.
8
7. When done, tighten up and install the waterproof connectors.
8. Assemble the camera components, e.g., the CS ring and lens module. Secure the
mounting plate to the bottom of the camera (the label side) using the included screw.
There is a plastic mount pad in the package. You do not need the mounting pad
using the VIVOTEK camera.
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
You may need to remove the RJ45 connector, and use a crimping tool to connect the
Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the
width of 4 ~ 6.5mm.
9
English
Lens flush
w/ edge of
enclosure
9. Adjust the camera's position so that the lens module can ush align with the tempered
glass. Secure the camera using the screws and washers to the bottom of the housing.
10. Connect 24V power source to the power input terminal. Connect power wires from
the DC 12V output to the camera. Connect the 24V power output to drive the external IRs.
DC 12V OUT - to camera
AC 24V OUT - to external IR
AC 24V IN - external power
source
Ground
Not used for this model
10
You should prepare a power adaptor of the sufcient capacity for supplying 24V input.
Below are the requirements:
Total consumption Power adaptor
LPC Highway 80W 7A
LPC Street 48W 5A
12. Also pass the combo cable of the IR illuminator through a waterproof connector.
13. Connect the day/night signal lines from the IR unit to the DI/DO connectors on the
camera's terminal block.
DO+
DO-
DI1+
DI2+
DI3+
DI-
RS485-
RS485+
AC/DC pwr
AC/DC pwr
The day/night mode DI connection enables the synchronization of IR light and the
automated day/night switching mechanism on the camera.
11. Connect the Ethernet cable to the camera's RJ45 socket.
Name Color Gauge Description
V+ Red (20AWG) Power input
12~24V DC±10%
24V AC±10% (50~60Hz), (14.5VDC current controlled)
V- Black (20AWG)
DI+ Green (26AWG) LED ON/OFF control
* Dry contact
Logic level 1(Open) = LED off
Logic level 0(Close to GND) = LED on
* Wet contact
Logic level 1: 4V~40 V = LED off
Logic level 0: 0.8V MAX = LED on
DI- Yellow (26AWG) Ground
DO+ Purple (26AWG) Light sensor status output
1. Open = Day
2. Short = Night (20 lux for IR ON)
DO- Blue (26AWG) Ground
RS485+ Orange (26AWG) RS485 interface control
RS485- Brown (26AWG)
Cable Pinouts (IR Illuminator)
Table des matières
Autres manuels Vivotek Caméra de sécurité
Vivotek
Vivotek FD8365EHV Manuel utilisateur
Vivotek
Vivotek IP8332-C Manuel utilisateur
Vivotek
Vivotek IP7139 Manuel utilisateur
Vivotek
Vivotek PT3114 Manuel utilisateur
Vivotek
Vivotek FD9171-HT Manuel utilisateur
Vivotek
Vivotek FD8166 Manuel utilisateur
Vivotek
Vivotek FD8372 Manuel utilisateur
Vivotek
Vivotek IP8362 Manuel utilisateur
Vivotek
Vivotek IP8371E Manuel utilisateur
Vivotek
Vivotek IP8331 Manuel utilisateur
Vivotek
Vivotek 4X-FD7132 Manuel utilisateur
Vivotek
Vivotek Supreme MD8531H Manuel utilisateur
Vivotek
Vivotek FD8362/62E Manuel utilisateur
Vivotek
Vivotek FE8173 Manuel utilisateur
Vivotek
Vivotek IB9367-H Manuel utilisateur
Vivotek
Vivotek SUPREME IP9165-HP Manuel utilisateur
Vivotek
Vivotek FD8138-H Manuel utilisateur
Vivotek
Vivotek FD9391-EHTV Manuel utilisateur
Vivotek
Vivotek MD7530 Manuel utilisateur
Vivotek
Vivotek IP7330 Manuel utilisateur
