Vivace HART VTT10-FH Guide rapide

INSTALLATION, OPERATION, CONFIGURATION AND MAINTENANCE MANUAL

July/2019

VTT10-FH

HART® TEMPERATURE TRANSMITTER

field model

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

manual, patent concession or model register of use/project.

No part of this publication may be reproduced, copied, processed or transmitted on any manner

or any medium (photocopy, scanning, etc.) without the express permission of Vivace Process

Instruments Inc., not even for training or electronic systems.

HART

is a registered mark of HART Communication Foundation.

NOTE

We have reviewed this manual with great care to maintain compliance with the hardware and

software versions described herein. However, due to the dynamic development and version upgrades,

the possibility of technical deviations cannot be ruled out. We cannot accept any responsibility for the

full compliance of this material.

Vivace reserves the right to, without notice, make modifications and improvements of any kind

in its products without incurring in any circumstances, the obligation to make those same modifications

to products sold previously.

The information in this manual is frequently updated. Therefore, when using a new product,

please check the latest version of the manual on the Internet through our website

www.vivaceinstruments.com, where it can be downloaded.

You customer is very important for us. We will always be grateful for any suggestions for

improvements as well as new ideas, which can be sent to the e-mail: contato@vivaceinstruments.com

preferably with the title "Suggestions".

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

SUMMARY

EQUIPMENT DESCRIPTION ........................................................................................................ 6

1.1.

BLO K DIAGRAM ......................................................................................................................................... 6

INSTALLATION ............................................................................................................................ 8

2.1.

ME HANI AL ASSEMBLY ........................................................................................................................... 9

2.2.

ELE TRI AL ONNE TION ...................................................................................................................... 11

2.3.

PRO ESS ONNE TION ........................................................................................................................... 13

CONFIGURATION ...................................................................................................................... 14

3.1.

LO AL ONFIGURATION .......................................................................................................................... 14

3.2.

JUMPER ONFIGURATION FOR LO AL ADJUST AND WRITE PROTE TION ...................................... 15

3.3.

LIQUID RYSTAL DISPLAY (L D) ............................................................................................................. 16

3.4.

LO AL ADJUST ONFIGURATION TREE ................................................................................................. 16

3.5.

HART

ONFIGURATOR ............................................................................................................................ 17

3.6.

HART ONFIGURATOR PROGRAMMING TREE ...................................................................................... 18

3.7.

FDT/DTM ONFIGURATION....................................................................................................................... 20

MAINTENANCE ..........................................................................................................................

4.1.

HART PROGRAMMER DIAGNOSTI S ...................................................................................................... 22

4.2.

ADDITIONAL DIAGNOSTI S ...................................................................................................................... 22

4.3.

ASSEMBLY AND DISASSEMBLY PRO EDURE ....................................................................................... 23

4.4.

SPARE PARTS ............................................................................................................................................ 24

CERTIFICATION ......................................................................................................................... 5

TECHNICAL CHARACTERISTICS ............................................................................................. 6

6.1.

IDENTIFI ATION ......................................................................................................................................... 26

6.2.

TE HNI AL SPE IFI ATION..................................................................................................................... 26

6.3.

OMPATIBLE SENSORS ............................................................................................................................ 27

6.4.

ORDERING ODE....................................................................................................................................... 28

WARRANTY ............................................................................................................................... 9

7.1.

GENERAL ONDITIONS ............................................................................................................................. 29

7.2.

WARRANTY PERIOD .................................................................................................................................. 29

APPENDIX ........................................................................................................................................ 30

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

It is extremely important that all the safety instructions, installation and operation in this manual are

followed faithfully. The manufacturer is not liable for damage or malfunction caused by improper use

of this equipment.

It is recommended to strictly following the rules and good practice relating to installation, ensuring

correct grounding, noise insulation and good quality cables and connections in order to provide the

best performance and durability to the equipment.

Special attention must be considered in relation to installations in hazardous areas, where applicable.

WARNING

•Appoint only skilled people, trained with process and equipment;

•Install equipment only in operation compatible areas, with the proper connections and

protections;

•Use proper safety equipment for any handling device in field;

•Turn area power off before equipment installation.

SAFETY PROCEDURES

SYMBOLOGY

Caution - indicates risk or error source

Important Information

General or Specific Risk

Electric Shock Danger

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

GENERAL INFORMATION

Vivace Process Instruments ensures the operation of this equipment, according to the

descriptions contained in its manual, as well as technical characteristics, not

guaranteeing its full performance in particular applications.

The operator of this equipment is responsible for observing all aspects of safety and

prevention of accidents applicable during the execution of the tasks in this manual.

Failures that might occur in the system, causing damage to property or injury to

persons, shall additionally be prevented by external means to a safe outlet for the

system.

This equipment must be used only for the purposes and methods proposed in this

manual.

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

1 EQUIPMENT DESCRIPTION

VTT10-FH is the field model for Vivace’s temperature transmitter family, projected to be installed

directly on sensor or on a Ø 2” tube, panel or wall. It attends several sensor types, such as thermocouple,

RTDs, resistance and millivoltage signals.

The transmitter is powered by a 12 to 45 Vdc voltage and modulates communication over a 4-20 mA

output signal, according to NAMUR NE43 standard, using HART

protocol. The configuration uses HART®

7 (older versions compatible) communication protocol, already established on the world of industrial

automation for configuration, calibration, monitoring and diagnostics.

Through a HART configurator or any EDDL or FDT/DTM-based tool it is possible to configure sensor

type, measuring range, work unit, calibration and also monitoring measured variables with device status.

Configuration via local adjust is also possible with an auxiliary magnetic screwdriver.

Focusing on high performance and robustness, it was projected with the most recent electronic

component and material technology, offering long-term reliability for every scale systems.

1.1. BLOCK DIAGRAM

Component modularization for transmitter is described on the following block diagram.

Figure 1.1 – Transmitter block diagram.

The sensor signal passes through RF EMI filter and goes to ADC block, where it is converted to a

digital value. This digital value later will be converted in the temperature, according to selected sensor type.

The temperature value is finally converted in a current signal, proportional to the calibrated range.

The sensor signal is galvanic isolated from output signal, avoiding ground loop.

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

The input block (DC power supply) is responsible for the electric source for all circuits. Current control

block is composed by a circuit to transform digital values generated by microcontroller into 4-20 mA electric

current, proportional to the primary variable value.

HART

channel and HART

modem blocks provide the interface between microcontroller signals

and HART

bus connected to monitored device. Local adjust block enables local configurations by user.

The display board has the controller block to interface LCD and CPU communication signals,

adapting all the messages to be shown on display.

Finally, the CPU block can be seen as the transmitter brain, where all the activities happen, such as

time control, HART

machine, besides the common transmitter routines: configuration, calibration and

generation of output current, proportional to the primary variable.

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

2 INSTALLATION

RECOMMENDATION

When taking the equipment to the installation location, transfer it in the original packaging.

Unpack the equipment at the installation location to avoid damage during transportation.

RECOMMENDATION

Model and specification of equipment are indicated on identification plate, located at the top of

the housing. Check if supplied specification and model correspond to application requirements.

STORAGE

The following precautions should be observed when storing the equipment, especially for a

long period:

1) Select a storage area that meets the following conditions:

a) No direct exposition to rain, water, snow or sunlight.

b) No exposition to vibration and shocks.

Normal temperature and humidity (around 20°C / 70°F, 65% RH)

However, it can also be stored under the following temperature and humidity intervals:

●Ambient Temperature: -40°C to 85°C (without LCD)* or -30°C to 80°C (with LCD)

●Relative Humidity: 5% to 98% RH (@ 40°C)

(2) For equipment storage, use original factory package (or similar).

(3) If storing an already used Vivace equipment, dry every moist part and clean all

connections that was in contact with the process. Keep covers and connections closed and

properly protected for its specific application and requirements.

* Only for general use. For explosion proof version, follow product certification requirements.

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

.1. MECHANICAL ASSEMBLY

VTT10-FH was developed to be installed in the field, thus supporting exposition to several

environment situations, keeping good performance through any temperature, humidity and vibration

variations.

The transmitter’s housing is IP67 protected, being immune to water contact to electronic circuit and

electrical connections, since cable gland or conduit for electrical connection is correctly assembled and

sealed with non-hardening substance. Covers must also be tight to avoid humidity, since housing screws

are not protected by painting.

The electronic circuit is protected by varnish but constant water or corrosion exposure may

compromise this protection and damage the electronic components.

Figure 2.1 shows the dimensional drawing and mounting positions for VTT10-FH.

Figure 2.1 – Dimensional and mounting drawings for VTT10-FH.

To avoid the risk of involuntary loss of VTT10-FH covers due to vibration, for instance, it can be

locked by screw, as shown on figure 2.2.

VTT10-FH is a field device, so it can be installed through a mounting bracket on a 2” tube attached

with a U clip. For best LCD positioning device enables its display to be rotated 4 x 90°, according to figure

2.3. The transmitter can also be attached with the same mounting bracket to a wall or panel.

VTT10-FH HART

TEMPERATURE TRANSMITTER INSTALLATION, OPERATION, ONFIGURATION AND MAINTENAN E MANUAL

______________________________________________________________________________________________________________________________

Figure 2.2 – Front cover lock.

Figure 2.3 – Housing positioning.

VTT10-FH liquid crystal display can be rotate 4 x 90° so indication will be adequate for user

visualization.

Figure 2.4 illustrates rotation possibilities for VTT10-FH LCD.

Figure 2.4 – 4 x 90° LCD rotation.

Table des matières

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur