Vitek VTD-VPH Manuel utilisateur
BLACK
VITEK
VTD-VPH
Vandal Resistant Color
Dome Camera Series
Product Manual
The VTD-VPH Vandal Resistant Dome Camera is a
smaller, more attractive camera ideal for use in
commercial or residential applications. It measures only 5”
in diameter and comes with a 24 Volt AC power input for
easy integration with standard cameras and power
systems. Versatile mounting and lens options allow you to
achieve perfect video images in virtually any environment.
All VTD-VPH domes feature Sony Super-HAD and/or
Ex-View Technology with Hi-Resolution of 480 Television
Lines.
2
CONTENTS OF PACKAGE
•One Fully Assembled VTD-VPH Series Dome Camera
•One Additional Knock-Out Plug
•One Tamper-Proof Wrench
•One Rubber Sealer Mat
•One Instruction/Installation Manual
•Assorted Additional screws for Convenience
Your VTD-VPH Dome Camera is designed to be flush or ceiling mounted on a wall or ceiling and
comes complete with a surface mount rear casing including conduit knockouts. Its patented 3-axis
gimbal allows for perfect viewing angles on any vertical or horizontal surface. An optional goose
neck wall mount (VT-VPHWM) is available if desired. The VTD-VPH Dome Camera is weather
sealed for indoor or outdoor locations.
The VTD-VPH Dome Camera should be powered by 24 Volts AC. Polarity is not important but you
should make sure that the power supply you are using is CSA Certified Class 2 Power Supply
delivering a minimum of 2.5 Watts.
For optimum video signal, use 95% copper shielded coax cable. Twisted pair or CAT-5E cable may
also be used with optional VT-TR1M Passive Video Transceivers. Maximum cable distance for 95%
copper braid coax is approximately. 800’; For Cat-5E or twisted pair, 2000’ using VT-TR1M
transceivers.
INSTALLATION OVERVIEW
WIRING CONNECTIONS
BLACK
3
FLUSH MOUNT INSTALLATION
Begin by removing the three tamper proof screws in the outer bezel with the special wrench
included and removing it. Continue by removing the tamper proof screws on the inner casing (you
may want to remove and set aside the polycarbonate bubble to avoid scratching it).
Remove the inner casing from the outer surface mount casing and set the outer casing aside. You
may want to keep the surface mount box in case you decide to re-mount it at a later time.
Cut a hole in the ceiling or wall the exact size of the inner back box and set the camera into the
hole securing it with anchors. When installing in a drop ceiling always attach a guy wire to a beam
above the camera to hold the weight and secure the camera for safety reasons.
Begin by removing the three tamper proof screws in the outer bezel with the special wrench
included and removing it. Continue by removing the tamper proof screws on the inner casing (you
may want to remove and set aside the polycarbonate bubble to avoid scratching it).
Remove the inner casing from the outer surface mount casing (back box) and temporarily set the
inner casing/camera to the side.
Secure the outer back box directly to a wall or ceiling using wood screws or anchors. If installing
outside, remember to glue the rubber matting to the wall and then attach the back box. Conduit
may be attached to the rear or the side of the back box depending on the installation.
Re-secure the inner casing with the camera to the back box but remember to attach the wiring
before doing so. You may also want to find a desirable angle of view and adjust the iris and focus
before making the final wiring connections.
Remove Inner Screws Detach CasingRemove Top Bezel
SURFACE MOUNT INSTALLATION
4
CAMERA SETUP
Your VTD-VPH Dome Camera has been set at average default settings from the factory so the
performance should be excellent right from the start. However, certain challenging environments
may require additional set-up procedures to enhance the image.
There are four dip switches on the rear board
of the camera. They should all be set to off
from the factory. The following adjustments may
be made:
DIP SWITCH SETTINGS
Electronic Shutter Control
Leave this switch in the “Off” position if your camera has an auto
iris lens.
Switch to the “On” position when using a fixed lens version to
enhance the camera’s ability to react to changing light.
Back Light Control
Leave this switch in the “Off” position if your camera is being
installed outdoors or if the installation is indoors in a controlled
lighting environment.
Switch to “On” position when installing the camera indoors looking
toward windows or doors or if outdoors looking into semi-direct
sunlight. Never install camera looking into direct sunlight.
Flickerless On/Off
Flickerless shutter speed for minimizing image flicker under
fluorescent lighting.
Auto White Balance
Switch “On” if the image appears discolored or floats between
colors. This will enable the camera to find “White”.
Dip Switch 1 =
Dip Switch 2 =
Dip Switch 3 =
Dip Switch 4 =
Dip Switch Adjustments
BBLLAACCKK
5
AUTO IRIS LENS ADJUSTMENT
Your DC Auto Iris Lens should be set properly at default from the factory. However, if the picture
appears too bright or too dark, the iris function can be adjusted by turning the small silver
potentiometer located on the board above the lens.
On all varifocal versions, the width of view may be
adjusted by turning the forward lever toward the
smaller number for wider and toward the larger number
for more telephoto.
The Focus may be adjusted by turning the rear lever
toward the “W” for near and toward the “T” for far (or
telephoto). After making these adjustments, tighten the
levers to lock them in place.
On the fixed version, the focus may be adjusted by
simply screwing or unscrewing the lens. Be careful
not to over tighten the lens or you may
damage the pick-up sensor.
Auto Iris Adjustment
Focus Adjustment
FIELD OF VIEW AND FOCUS ADJUSTMENT
6
ROUTINE MAINTENANCE
Use mild liquid cleaners to remove dirt and grime from the dome surface.
Do not use harsh or abrasive cleaners which can scratch the polycarbonate dome and reduce
visibility for the camera.
If the camera view is obstructed by scratches, remove the front plate (bezel) and rotate the bubble
to a portion that is not scratched.
If the dome becomes damaged or scratched beyond use, contact your distributor to order a
replacement.
VT-VPHWM
Goose Neck Wall Mount w/Cable Feed thru.
OPTIONAL EQUIPMENT
VTD-VPH/WM
BBLLAACCKK
7
DOME SPECIFICATIONS
Image Device
Effective Pixels
Resolution
Minimum Illumination
S/N Ratio
Electronic Shutter
AGC
Lens
Video Output
White Balance
Power Source
Power Consumption
Weight
Dimensions
Construction
IP Rating
1/3” High Resolution Super HAD Color CCD
768 x 494
480 TV Lines
Standard Cameras: 0.7 Lux / F1.2 (AGC On)
Day/Night Cameras: 0.03 Lux / F1.2 (AGC On) With Day/Night Function
More than 48dB (AGC off)
1/60 to 1/100,000 Sec.
Built-In (On)
VTD-VPH3.6: Color Camera With 3.6mm Fixed Iris Lens
VTD-VPH266: Color Camera With 2.6-6mm Varifocal Lens
VTD-VPH3895: Color Camera With 3.8-9.5mm Varifocal Lens
VTD-VPH412: Color Camera With 4-12mm Varifocal Lens
VTD-VPH266DN: Day/Night Color Camera With 2.6-6mm Varifocal Lens
VTD-VPH3895DN: Day/Night Color Camera With 3.8-9.5mm Varifocal Lens
VTD-VPH412DN: Day/Night Color Camera With 4-12mm Varifocal Lens
Composite: 1.0 Vp-p / 75 Ohm
Auto White Balance (AWB)
24VAC 60Hz
220mA
750 g. / 26.46 Oz. / 1.65 Lbs.
160mm x 99mm / 6.29” x 3.89” (D x H)
Aluminum/Tin Base - Polycarbonate Bubble
IP66/68
8
9970 GLENOAKS BLVD. UNIT B SUN VALLEY, CA 91352
PHONE: 888-VITEK-70 / 818-771-0300 FAX: 818-771-0400
WWW.VITEKCCTV.COM | SALES@VITEKCCTV.COM
LIMITED LIABILITY WARRANTY
Your new Camera is guaranteed to be free from defects in materials
and workmanship for a period of two years from the date of
purchase.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental
damage, caused by excessive voltage or lightning.
The product must not have been tampered with in any way then the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact VITEK or your local distributor if servicing should become
necessary.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Vitek Caméra de sécurité
Vitek
Vitek VTC-C661 Manuel utilisateur
Vitek
Vitek Mighty Series Manuel utilisateur
Vitek
Vitek VTC-TNT4RFS Manuel utilisateur
Vitek
Vitek VTD-A4F/VW Manuel utilisateur
Vitek
Vitek VTD-MH2910 Manuel utilisateur
Vitek
Vitek VTC-TNB4RMA4 Manuel utilisateur
Vitek
Vitek VTD-VH49B2 Manuel utilisateur
Vitek
Vitek VTD-M2HET2812 Manuel utilisateur
Vitek
Vitek VTC-AR2B4FN Manuel utilisateur
Vitek
Vitek VT-IR1B/24 Manuel utilisateur
Vitek
Vitek VTC-TNT4RMS Manuel utilisateur
Vitek
Vitek VTD-MD5CH Manuel utilisateur
Vitek
Vitek VTC-THB8R2 Manuel utilisateur
Vitek
Vitek VTC-TNB8RMA4B Manuel utilisateur
Vitek
Vitek VTD-MD2-4 Manuel utilisateur
Vitek
Vitek Transcend VTC-THB5R3/R2 Manuel utilisateur
Vitek
Vitek VTC-HOCRBD4F Manuel utilisateur
Vitek
Vitek VTC-IRM5H-2713 Manuel utilisateur
Vitek
Vitek VTC-TTB42R2F Manuel utilisateur
Vitek
Vitek VTD-C13A Manuel utilisateur
