Vista 2500 Manuel utilisateur

IN GROUND INSTALLATION POUR CONCRETE INSTALLATION

INSTALLATION INSTRUCTIONS FOR 12 VOLT

BOLLARD

MODEL #2500

FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT

EXCEED 25 AMPS, 15 VOLT MAX.

WARNING: Bollard luminaires must be installed in accordance with

the National Electrical Code (NEC) and local codes. Failure to do so

will void the warranty and may result in serious injury and/or damage to the bollard luminaire.

SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used.

Lens and metal around lamp can become hot enough to blister hands. Particular care

should be taken not to locate luminaires where small children can reach them if high wattage lamps are used.

LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A

POOL OR SPA. SECONDARY CABLE IS NOT TO BE BURIED MORE THAN

6". WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED

TOTAL WATTS OF TRANSFORMER RATING. DO NOT USE EXTENSION

CORDS ON POWER UNITS.

NOTE: Always use UL recognized wire connectors for connections.

NOTE: Save these instructions for future reference.

BOLLARD IS UL LISTED FOR ABOVE GROUND INSTALLATION ONLY.

TOOLS REQUIRED FOR INSTALLATION:

Flat head screwdriver Shovel Wire strippers Cement concrete (if pour concrete method chosen)

INSTRUCTIONS FOR STAKE MOUNT INSTALLATION

NOTE: Your Vista 12 volt Bollards are shipped with a ground stake to facilitate a stake mount

installation. However, for a permanent and secure installation a concrete footing

support for the bollard base is recommended.

1. To prevent electrical shock, disconnect transformer from electrical supply before installation

or service.

2. Dig a hole at selected location.

3. Using the 1/2" threaded short nipple (provided), attach ground stake to center hole in

bollard base and insert stake with base into the ground until bottom of base is even with grade.

Base Set Screw

Post

Lens Set Screw

Lens

Base

Grade

Concrete

Lens

Post

Base Set Screw

Base

Grade

Lens Set Screw

4. Run wire pigtail through bottom hole of base and strip the two (2) leads from the

bollard wire. Using the two (2) silicone filled safety connectors (provided), connect the leads

from the bollard to the main supply cable leads.

NOTE: Luminaires are supplied with 36" of 18-2 cable pigtail for secure connection to the main

supply cable. The wire is to be protected by routing in close proximity to the luminaire.

The wiring shall be buried a maximum of 6 inches (15.2 cm) in order to connect the

main supply cable.

5. Slip bollard over base and tighten set screws.

6. Provide power to the luminaire and check for proper operation.

INSTRUCTIONS FOR POUR CONCRETE INSTALLATION

1. To prevent electrical shock, disconnect transformer from electrical supply before installation

or service.

2. Dig a hole at selected location.

3. Using the 1/2" threaded short nipple (provided), attach ground stake to center hole in

bollard base and insert stake with base into the ground until bottom of base is even with grade.

4. Run wire pigtail through bottom hole of base and strip the two (2) leads from the

bollard wire. Using the two (2) silicone filled safety connectors (provided), connect the leads

from the bollard to the main supply cable leads.

NOTE: Luminaires are supplied with 36" of 18-2 cable pigtail for secure connection to the main

supply cable. The wire is to be protected by routing in close proximity to the luminaire.

The wiring shall be buried a maximum of 6 inches (15.2 cm) in order to connect the

main supply cable.

5. Pour concrete at least 2" thick.

6. Slip bollard over base and tighten set screws.

7. Provide power to the luminaire and check for proper operation.

IMPORTANT SAFETY INSTRUCTIONS

LIGHTED LAMP IS HOT!!

WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO PERSONS:

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamps get hot quickly! Contact only switch/plug when turning on.

3. Do not touch hot lens, guard or enclosure.

4. Keep lamp away from material that may burn.

5. Do not touch the lamp at any time. Use a soft cloth. Oil from

the skin may damage lamp.

6. Do not operate luminaire fitting with a missing or damaged cover.

LAMP INSTALLATION/REPLACEMENT:

CAUTION: Do not exceed maximum wattage marked on luminaire

label.

1. To prevent electrical shock, disconnect transformer from electrical supply before

service.

2. Loosen the two (2) base set screws and remove luminaire from base.

3. Replace lamp with correct wattage and type marked on fixture label.

NOTE: DO NOT touch lamp with bare hands. Always use soft cloth or the

plastic wrapping (if available) from the lamp to handle the lamp.

4. Re-install luminaire and tighten the two (2) base set screws.

VISTAPROFESSIONALOUTDOORLIGHTING DivisionofU.S.T.E.Inc. Website:www.vistapro.com

1625 SurveyorAvenue,SimiValley,CA93063 (805)527-0987 FAX:(805)527-6830 (800)766-847

Table des matières

Autres manuels Vista Éclairage extérieur

Vista

Vista 7216 Landscape Series Manuel utilisateur

Vista

Vista 1218 Manuel utilisateur

Vista

Vista Architectural Series Manuel utilisateur

Vista

Vista 12V Series Manuel utilisateur

Vista

Vista 1447 Manuel utilisateur

Vista

Vista 6223 Landscape Series Manuel utilisateur

Vista

Vista 5250 Manuel utilisateur

Vista

Vista 9216 Landscape Series Manuel utilisateur

Vista

Vista Landscape Series Manuel utilisateur

Vista

Vista 1093 Manuel utilisateur

Vista

Vista 2165 Manuel utilisateur

Vista

Vista Landscape Series Manuel utilisateur

Vista

Vista Architectural 1092 Manuel utilisateur

Vista

Vista 9222 Landscape Series Manuel utilisateur

Vista

Vista 1039 Manuel utilisateur

Vista

Vista 4017 Manuel utilisateur

Vista

Vista Landscape Series Manuel utilisateur

Vista

Vista 2166 Series Manuel utilisateur

Vista

Vista 5104 Manuel utilisateur

Vista

Vista 5203 Series Manuel utilisateur

Vista

Vista Architectural Series Manuel utilisateur

Vista

Vista 6216 Landscape Series Manuel utilisateur

Vista

Vista 2117 Manuel utilisateur

Vista

Vista 7223 Landscape Series Manuel utilisateur

Manuels Éclairage extérieur populaires d'autres marques

Sealey

Sealey LED37 Manuel utilisateur

nordlux

nordlux VEJERS Guide de l'utilisateur

SImx

SImx ELITE LED LHTC637 Manuel utilisateur

GEV

GEV CAROLINE 10833 Manuel utilisateur

NEBO

NEBO NEB-LSP-0020 Manuel utilisateur

WE-EF

WE-EF PFL540 LED Manuel utilisateur

Lindby

Lindby 9949029 Manuel utilisateur

HEPER

HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation

HEPER

HEPER LW8034.003-US Instructions d'installation et d'utilisation

Maretti

Maretti VIBE S 14.6080.04.A Manuel utilisateur

BEGA

BEGA 84 253 Manuel

HEPER

HEPER MINIMO Instructions d'installation et d'utilisation

LIGMAN

LIGMAN BAMBOO 3 Manuel utilisateur

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur

urban ambiance

urban ambiance UQL1273 Manuel utilisateur

TotalPond

TotalPond 52238 Manuel utilisateur

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuel utilisateur