ViewSonic CDE5561T Manuel utilisateur
CDE5561T/CDE6561T/CDE7061T/
CDE8452T/SWB5561B/SWB6561B/
SWB7061B/SWB8452B
LCD Display
User Guide
Model No. VS16480/VS16477/VS16436/VS15420
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specic languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Thank you for choosing ViewSonic
Withover25yearsasaworldleadingproviderofvisualsolutions,ViewSonic
is dedicated to exceeding the world’s expectations for technological
evolution, innovation, and simplicity. At ViewSonic, we believe that our
products have the potential to make a positive impact in the world, and
we are confident that the ViewSonic product you have chosen will serve
you well.
Once again, thank you for choosing ViewSonic !
i
Compliance Information
NOTE: This section addresses all connected requirements and statements regarding
regulations. Confirmed corresponding applications shall refer to nameplate labels
and relevant markings on unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2012/19/EU (WEEE).The mark indicates
the requirement NOT to dispose the equipment as unsorted municipal
waste, but use the return and collection systems according to local law.
ii
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India) This product complies
with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for
the exemptions set in Schedule 2 of the Rule.
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
iii
Cautions and Warnings
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings and follow all instructions.
4. Always handle the LCD display with care when moving it.
5. Never remove the rear cover. This LCD display contains high-voltage parts.
You may be seriously injured if you touch them.
6. Do not use this equipment near water. Warning: To reduce the risk of fire or
electric shock, do not expose this apparatus to rain or moisture.
7. Avoid exposing the LCD display to direct sunlight or another heat source. Orient
the LCD display away from direct sunlight to reduce glare.
8. Clean with a soft, dry cloth. If further cleaning is required, see the “Care and
Maintenance” section in this guide for further instructions.
9. Avoid touching the screen. Skin oils are difficult to remove.
10. Do not rub or apply pressure to the LCD panel, as it may permanently damage
the screen.
11. Do not block any ventilation openings. Install the equipment in accordance with
the manufacturer’s instructions.
12. Do not install near any heat sources such as radiators, heat registers, stoves, or
other devices (including amplifiers) that produce heat.
13. Place the LCD display in a well ventilated area. Do not place anything on the
LCD display that prevents heat dissipation.
14. Do not place heavy objects on the LCD display, video cable, or power cord.
15. If smoke, an abnormal noise, or a strange odor is present, immediately switch
the LCD display off and call your dealer or ViewSonic. It is dangerous to continue
using the LCD display.
16. Do not attempt to circumvent the safety provisions of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade
and the third prong are provided for your safety. If the plug does not fit into your
outlet, consult an electrician for replacement of the outlet.
17. Protect the power cord from being tread upon or pinched, particularly at the plug,
and the point where if emerges from the equipment. Be sure that the power outlet
is located near the equipment so that it is easily accessible.
18. Only use attachments/accessories specified by the manufacturer.
(Continued on next page)
iv
19. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the equipment. When a cart is used,
use caution when moving the cart/equipment combination to avoid
injury from tipping over.
20. Unplug this equipment when it will be unused for long periods of time.
21. Refer all servicing to qualified service personnel. Service is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
22. The Unit is a Monitor with LED backlight intended for general office used.
v
Contents
Compliance Information
FCC Compliance Statement................................................................ i
Industry Canada Statement................................................................. i
CE Conformity for European Countries............................................... i
Indian Restriction of Hazardous Substances ......................................ii
Declaration of RoHS2 Compliance......................................................ii
Cautions and Warnings......................................................................iii
Copyright Information
Product Registration........................................................................... 2
For Your Records............................................................................... 2
1. Getting Started
1.1 Package Contents........................................................................ 3
1.2 Wall Mount Kit Specifications (VESA).......................................... 4
2. Smart Whiteboard/LCD Display
Features
2.1 Control Panel Overview................................................................ 5
2.2 Terminal Interface Overview ........................................................ 6
2.3 Remote Control Overview ............................................................ 7
2.4 Inserting Remote Control Batteries .............................................. 9
2.5 Remote Control Receiver Range ............................................... 10
3. Setting Up Your Display
3.1 Connecting an External PC........................................................ 11
3.2 RS232 Connections ................................................................... 12
3.3 Connecting USB Peripherals...................................................... 13
3.4 AV IN Connections..................................................................... 14
3.5 HDMI Connections ..................................................................... 15
3.6 Coaxial Connections .................................................................. 15
3.7 VGA Connections....................................................................... 16
vi
4. OSD Menu Operation
4.1 General Setting .......................................................................... 17
4.2 More OSD settings..................................................................... 19
4.3 Annotation Menu ........................................................................ 22
4.5 Embd Player Interface................................................................ 23
4.6 Multimedia File Playback Interface............................................. 31
5. Trouble Shooting
6. Care and Maintenance
7. Display Modes
7.1 VGA Mode.................................................................................. 39
7.2 HDMI Mode ................................................................................ 40
8. Specifications
9. RS-232 Protocol
9.1 Introduction................................................................................. 42
9.2 Description ................................................................................. 42
9.2.1 Hardware specification............................................................ 42
9.2.2 Communication Setting ........................................................... 43
9.2.3 Command Message Reference............................................... 43
9.3 Protocol ...................................................................................... 43
9.3.1 Set-Function Listing................................................................. 43
9.3.2 Get-Function Listing ................................................................ 49
9.3.3 Remote Control Pass-through mode....................................... 53
Other Information
Customer Support ............................................................................ 56
Limited Warranty .............................................................................. 57
Mexico Limited Warranty.................................................................. 59
1
Copyright Information
Copyright © ViewSonic Corporation, 2016. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS, DisplayPort, and DDC are trademarks of VESA.
is a trademark of SRS Labs, Inc.
Premium Sound technology is incorporated under license from SRS Labs, Inc.
ENERGY STAR®is a registered trademark of the U.S. Environmental Protection
Agency (EPA).
As an ENERGY STAR®partner, ViewSonic Corporation has determined that this
product meets the ENERGY STAR®guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specifications without notice. Information in this
document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
2
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
Your LCD displays serial number is located on the rear side of the display.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
CDE5561T/CDE6561T/CDE7061T/CDE8452T/
SWB5561B/SWB6561B/SWB7061B/SWB8452B
ViewSonic LCD Display
VS16480/VS16477/VS16436/VS15420
CDE5561T/CDE6561T/CDE7061T/CDE8452T/
SWB5561B/SWB6561B/SWB7061B/SWB8452B_UG_
ENG Rev. 1B 02-19-16
_______________________________________
_______________________________________
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
Ce manuel convient aux modèles suivants
11
Table des matières
Autres manuels ViewSonic Moniteur
ViewSonic
ViewSonic E771 - 17" CRT Display Manuel utilisateur
ViewSonic
ViewSonic VP2250WB - 21.6" LCD Monitor Manuel utilisateur
ViewSonic
ViewSonic VA2715-h Manuel utilisateur
ViewSonic
ViewSonic VG3209-4K Manuel utilisateur
ViewSonic
ViewSonic VP920B - ThinEdge - 19" LCD Monitor Manuel utilisateur
ViewSonic
ViewSonic VX2423w Manuel utilisateur
ViewSonic
ViewSonic VP2000S Manuel utilisateur
ViewSonic
ViewSonic VA1616W-6 VS12018 Manuel utilisateur
ViewSonic
ViewSonic ViewPanel VE170 Manuel utilisateur
ViewSonic
ViewSonic Q241WB - Optiquest - 24" LCD Monitor Manuel utilisateur
ViewSonic
ViewSonic VA2756-4K-MHD Manuel utilisateur
ViewSonic
ViewSonic VS11869 Manuel utilisateur
ViewSonic
ViewSonic PF790 - 19" CRT Display Manuel utilisateur
ViewSonic
ViewSonic E90F - 19" CRT Display Manuel utilisateur
ViewSonic
ViewSonic VX2450w-LED Manuel utilisateur
ViewSonic
ViewSonic VG2453-CN Manuel utilisateur
ViewSonic
ViewSonic E96f+SB Manuel utilisateur
ViewSonic
ViewSonic VA926 - 19" LCD Monitor Guide de démarrage rapide
ViewSonic
ViewSonic VA2409-mh Manuel utilisateur
ViewSonic
ViewSonic EA771 Manuel utilisateur
