Viessmann VITODENS 050-W Manuel utilisateur

5685058 GB 8/2017 Dispose after installation.

Installation instructions

for contractors

VIESMANN

Converting the gas type from natural gas to LPG

for Vitodens 050-W

Safety instructions

Please follow these safety instructions closely to prevent accidents

and material losses.

Safety instructions explained

Danger

This symbol warns against the

risk of injury.

!Please note

This symbol warns against the

risk of material losses and envi-

ronmental pollution.

Note

Details identified by the word "Note"

contain additional information.

Installation, initial start-up, inspection,

maintenance and repairs must only be

carried out by a competent person

(heating engineer/installation contrac-

tor).

Before working on the equipment/heat-

ing system, isolate the power supply

(e.g. by removing a separate mains

fuse or by means of a mains isolator)

and safeguard against unauthorised

reconnection.

When using gas as fuel, also close the

main gas shut-off valve and safeguard

against unauthorised reopening.

Repairing components which fulfil a

safety function can compromise the

safe operation of your heating system.

For replacements, use only original

spare parts supplied or approved by

Viessmann.

Opening the Vitodens

Installation and service instruc-

tions

Replacing the gas train

Note

The Vitodens may be equipped with different gas train versions.

■Pressure die cast casing A

■Bolted casing B

1. Pull cable from gas train.

2. Undo union nut H and remove old

gas gasket.

3. Undo 2 screws C and remove gas

train.

4. For boilers equipped with gas train

A, insert new gasket D with cor-

rect new gas restrictor F for the

relevant gas type from the conver-

sion kit.

!Please note

Ensure the gas restrictor is

fitted correctly.

If equipped with gas train B (bol-

ted casing), insert new gasket D

with gas restrictor E from the con-

version kit for the relevant gas type.

Converting the gas type to LPG P (G31)

5685058

5. Mount gas train with new gas gas-

ket G.

Torque for fixing screws C: 6 Nm

Torque for union nut B: 30 Nm

6. Start the boiler.

7. Check all gas connections for tight-

ness.

Danger

Escaping gas leads to a risk

of explosion.

Check all gas equipment for

tightness.

!Please note

The use of leak detection

spray can result in faulty

operation.

Leak detection spray must

not come into contact with

electrical contacts or seal

the diaphragm opening on

the gas valve.

Changing the gas type at the control unit

1. Turn on the ON/OFF switch.

2. Press MODE and simultaneously

and hold for 3 s.

"SERV" appears on the display

and "I" flashes.

3. Use / to select "5" and confirm

with OK.

"0" flashes on the display.

4. Use / to select "1" and confirm

with OK.

The burner has been converted to

operation with LPG.

5. Press MODE and simultaneously

and hold for 3 s.

Service mode is terminated. Serv-

ice mode also terminates automati-

cally after 30 min.

6. Turn the ON/OFF switch off and on

again.

The selected gas type is now ena-

bled.

Converting the gas type to LPG P (G31) (cont.)

5685058

1. Connect a flue gas analyser at flue

gas port A on the boiler flue con-

nection.

2. Start the boiler.

3. To check the CO2 content the

burner output can be adjusted man-

ually.

Set the burner output at the boiler

control unit:

1. Press MODE.

2. / repeatedly until "SERV"

appears.

3. Press OK to confirm.

"OFF" appears on the display.

4. Use / to adjust the burner out-

put:

Display

shows

Burner out-

put

_ 20 20 %

_ _ 40 40 %

_ _ _ 60 60 %

_ _ _ _ 80 80 %

_ _ _ _ _ 100 100 %

5. Confirm your settings with OK.

Checking the CO2 content

5685058

4. Set the higher heating output

(100 %) and check the CO2 con-

tent.

The CO2 content must be within the

following range for the respective

gas type. See table.

Gas type CO2 content

in %

E (G20) 7.5 – 10.5

P (G31) 10.0 – 12.0

5. Set the lower heating output (20 %)

and check the CO2 content.

The CO2 content must be between

0.3 and 0.9 % below the value of

the upper heating output (100 %).

6. ■ If the CO2 content is within the

range indicated, continue with

step 6.

■ If the CO2 content lies outside

the given range, check the bal-

anced flue system for tightness.

Remedy any leaks.

Replace gas train if required.

7. Re-check the CO2 content for the

higher and lower heating output.

8. Use / to set the burner output to

"OFF".

9. Press MODE, "SERV" is no longer

shown.

Note

The function also terminates auto-

matically after 30 min.

Checking the CO2 content (cont.)

5685058

1. Shut down the boiler, remove the

flue gas analyser and close flue

gas test port A.

2. Select the appropriate label from

the "Gas type" labels supplied and

affix it next to the type plate on the

top of the boiler.

Note

The delivered condition shown on

the type plate then no longer

applies.

3. Mount the front panel and start the

boiler.

Starting the boiler

5685058

Viessmann Limited

Hortonwood 30, Telford

Shropshire, TF1 7YP, GB

Telephone: +44 1952 675000

Fax: +44 1952 675040

E-mail: [email protected]

Viessmann Werke GmbH & Co. KG

D-35107 Allendorf

Telephone: +49 6452 70-0

Fax: +49 6452 70-2780

www.viessmann.com

5685058 Subject to technical modifications.

Autres manuels pour VITODENS 050-W

Table des matières

Autres manuels Viessmann Chaudière

Viessmann

Viessmann VITOCROSSAL 200 Manuel d'instructions

Viessmann

Viessmann VITOROND 200 VD2A-125 Manuel utilisateur

Viessmann

Viessmann VITORONDENS 200-T Mode d'emploi

Viessmann

Viessmann Vitodens 222-F B2TB Guide de l'utilisateur

Viessmann

Viessmann Vitodens 100-W WB1C Manuel utilisateur

Viessmann

Viessmann VITODENS 050-W Guide rapide

Viessmann

Viessmann VITOCROSSAL 300 Mode d'emploi

Viessmann

Viessmann Vitodens 100-W Guide rapide

Viessmann

Viessmann VITOCROSSAL 300 Manuel utilisateur

Viessmann

Viessmann VITOGAS 100 Mode d'emploi

Viessmann

Viessmann VITODENS 050-W Guide rapide

Viessmann

Viessmann Vitodens 242-F Guide de démarrage rapide

Viessmann

Viessmann Vitogas 100 GS1 Series Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Manuel utilisateur

Viessmann

Viessmann VITOPLEX 100?LS Guide rapide

Viessmann

Viessmann VITOCELL 100-V Guide rapide

Viessmann

Viessmann Vitodens 100-W B1HF Series Guide rapide

Viessmann

Viessmann Vitoligno 300-H Mode d'emploi

Viessmann

Viessmann VITORONDENS 200-T Mode d'emploi

Viessmann

Viessmann Vitodens 222-F Manuel utilisateur

Viessmann

Viessmann Vitodens 200-W System Manuel utilisateur

Viessmann

Viessmann VITOCROSSAL 300 Manuel d'instructions

Viessmann

Viessmann Vitodens 100-W Guide rapide

Viessmann

Viessmann VR1 22 Guide rapide

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur

Radiant

Radiant R2K 55 Manuel