Viessmann VITORONDENS 200-T Mode d'emploi

Service instructions

for contractors

VIESMANN

Vitorondens 200-T

Type J2RA, 67.6 to 107.3 kW

Oil Unit condensing boiler

For applicability, see the last page

VITORONDENS 200-T

5614 313 UAE 2/2013 Please keep safe.

Please follow these safety instructions closely to prevent accidents and mate-

rial losses.

Safety instructions explained

!Please note

This symbol warns against the

risk of material losses and envi-

ronmental pollution.

Note

Details identified by the word "Note" con-

tain additional information.

Target group

These instructions are exclusively inten-

ded for qualified contractors.

■ Work on electrical equipment must

only be carried out by a qualified elec-

trician.

■ The system must be commissioned by

the system installer or a qualified per-

son authorised by the installer.

Regulations

Observe the following when working on

this system:

■ National installation requirements

■ Legal instructions regarding the pre-

vention of accidents

■ Legal instructions regarding environ-

mental protection

■ The Code of Practice of relevant trade

associations

■ All current safety regulations as

defined by DIN, EN, DVGW, VDE and

all locally applicable standards

aÖNORM, EN and ÖVE

cSEV, SUVA, SVTI and SWKI

Working on the system

■ Isolate the system from the power sup-

ply (e.g. by removing the separate fuse

or by means of a mains isolator) and

check that it is no longer 'live'.

■ Safeguard the system against unau-

thorised reconnection.

!Please note

Electronic assemblies can be

damaged by electrostatic dis-

charge.

Before beginning work, touch

earthed objects, such as heating

or water pipes, to discharge static

loads.

Repair work

!Please note

Repairing components that fulfil a

safety function can compromise

the safe operation of your sys-

tem.

Replace faulty components only

with original Viessmann spare

parts.

Safety instructions

5614 313 UAE

Auxiliary components, spare and

wearing parts

!Please note

Spare and wearing parts that

have not been tested together

with the system can compromise

its function. Installing non-author-

ised components and making

non-approved modifications or

conversions can compromise

safety and may invalidate our

warranty.

For replacements, use only orig-

inal spare parts supplied or

approved by Viessmann.

Safety instructions

Safety instructions (cont.)

5614 313 UAE

Product information

Intended use......................................................................................................... 5

Commissioning, inspection, maintenance

Steps - commissioning, inspection and maintenance.......................................... 6

Further details regarding the individual steps....................................................... 7

Parts lists

Parts lists.............................................................................................................. 20

Overview of the assemblies................................................................................. 21

Heat exchanger assembly.................................................................................... 22

Boiler body assembly........................................................................................... 23

Thermal insulation assembly................................................................................ 24

Commissioning/service reports........................................................................ 26

Specification....................................................................................................... 27

Certificates

Declaration of conformity...................................................................................... 28

Manufacturer's certificate according to the 1st BImSchV [Germany]................... 29

Keyword index.................................................................................................... 30

Index

5614 313 UAE

The appliance is only intended to be

installed and operated in sealed unven-

ted heating systems that comply with

EN 12828, with due attention paid to the

associated installation, service and

operating instructions. It is only designed

for the heating of water that is of potable

water quality.

Intended use presupposes that a fixed

installation in conjunction with permissi-

ble, system-specific components has

been carried out.

Commercial or industrial usage for a pur-

pose other than heating the building or

DHW shall be deemed inappropriate.

Any usage beyond this must be

approved by the manufacturer for the

individual case.

Incorrect usage or operation of the appli-

ance (e.g. the appliance being opened

by the system user) is prohibited and

results in an exclusion of liability. Incor-

rect usage also occurs if the components

in the heating system are modified from

their intended use (e.g. if the flue gas and

ventilation air paths are sealed).

Product information

Intended use

5614 313 UAE

For further information regarding the individual steps, see the page indicated

Commissioning steps

Inspection steps

Maintenance steps Page

••• 1. Commissioning the system........................................... 7

•2. Filling the heating system.............................................. 8

•3. Venting the heating system

• • 4. Shutting down the system

• • 5. Draining the heating system (if required)..................... 9

• • 6. Opening the boiler door................................................. 10

• • 7. Cleaning the heating surfaces....................................... 11

• • 8. Checking gaskets and thermal insulation sections.... 13

•9. Fitting the boiler door..................................................... 14

• • 10. Separating the neutralising system (if installed) from

the boiler and connecting the drain hose.................... 15

• • 11. Checking the neutralising system (if installed)........... 15

• • 12. Checking the connection on the flue gas side for leaks 16

• • 13. Cleaning the condensate drain pipe and siphon and

reconnecting to the drainage system........................... 17

•14. Filling the siphon and neutralising system

(accessories) with water................................................ 17

••• 15. Checking connections and sensor well on the heating

water side for tightness

••• 16. Checking the function of the safety equipment

• • 17. Checking the expansion vessel and system pressure 18

••• 18. Checking the thermal insulation for firm seating

• • 19. Checking the mixer for ease of operation and leaks... 18

••• 20. Adjusting the burner...................................................... 18

•21. Instructing the system user........................................... 19

•22. Operating and service documents................................ 19

Commissioning, inspection, maintenance

Steps - commissioning, inspection and maintenance

5614 313 UAE

Commissioning the system

Operating instructions, service

instructions – control unit and

burner

1. Check that the installation room vent

is open.

2. Check the pre-charge pressure of the

expansion vessel.

If the pre-charge pressure of the

expansion vessel is lower than the

static system pressure, top up with

sufficient nitrogen to raise the pre-

charge pressure higher (0.1 to

0.2 bar/10 to 20 kPa) than the static

system pressure.

The static pressure corresponds to

the static head.

3. Open the check valves.

4. Fill the heating system with water and

vent it until the charge pressure is

higher (0.1 to 0.2 bar/10 to 20 kPa)

than the pre-charge pressure of the

expansion vessel (see page 18).

Permiss. operating pressure: 3 bar

(0.3 MPa)

Mark the charge pressure at pressure

gauge A.

6. Return the check valves to their oper-

ating position.

7. Open the oil shut-off valves.

Commissioning, inspection, maintenance

Further details regarding the individual steps

5614 313 UAE

Filling the heating system

Fill water

!Please note

Unsuitable fill water increases

the level of deposits and corro-

sion and may lead to boiler dam-

age.

■ Flush the heating system thor-

oughly before filling.

■ Only use fill water of potable

quality.

■ An antifreeze additive suitable

for heating systems can be

added to the fill water. The anti-

freeze manufacturer must ver-

ify its suitability.

■ Fill and top-up water with a

water hardness in excess of

the following values must be

softened, e.g. with a small soft-

ening system for heating water.

Total permissible hardness of the fill and top-up water

Total heating

output

Specific system volume

kW < 20 l/kW ≥ 20 l/kW to

< 50 l/kW

≥ 50 l/kW

≤ 50 ≤ 3.0 mol/m3

(16.8 °dH)

≤ 2.0 mol/m3

(11.2 °dH)

< 0.02 mol/m3

(0.11 °dH)

> 50 to ≤ 200 ≤ 2.0 mol/m3

(11.2 °dH)

≤ 1.5 mol/m3

(8.4 °dH)

< 0.02 mol/m3

(0.11 °dH)

> 200 to ≤ 600 ≤ 1.5 mol/m3

(8.4 °dH)

≤ 0.02 mol/m3

(0.11 °dH)

< 0.02 mol/m3

(0.11 °dH)

> 600 < 0.02 mol/m3

(0.11 °dH)

< 0.02 mol/m3

(0.11 °dH)

< 0.02 mol/m3

(0.11 °dH)

Commissioning, inspection, maintenance

Further details regarding the individual steps (cont.)

5614 313 UAE

AFilling/draining

Note

Let the heating circuit pump run whilst

filling in order to vent the indirect coils.

Draining the heating system (if required)

Drain at filling/draining connector A.

Commissioning, inspection, maintenance

Further details regarding the individual steps (cont.)

5614 313 UAE

Opening the boiler door

lÖ

Commissioning, inspection, maintenance

Further details regarding the individual steps (cont.)

5614 313 UAE

Autres manuels pour VITORONDENS 200-T

Table des matières

Autres manuels Viessmann Chaudière

Viessmann

Viessmann Vitodens 200-W System Mode d'emploi

Viessmann

Viessmann Vitodens 222-F Mode d'emploi

Viessmann

Viessmann B2HB 45 Manuel utilisateur

Viessmann

Viessmann VITODENS 333 Mode d'emploi

Viessmann

Viessmann VITODENS 100-W B1HE Manuel utilisateur

Viessmann

Viessmann VITOCROSSAL 300 Manuel utilisateur

Viessmann

Viessmann VITOCROSSAL Series Manuel utilisateur

Viessmann

Viessmann Vitodens 200-W System Guide de démarrage rapide

Viessmann

Viessmann Vitodens 100-W Guide rapide

Viessmann

Viessmann VITOCROSSAL 300 Mode d'emploi

Viessmann

Viessmann Vitodens 100-W Guide rapide

Viessmann

Viessmann CM2-620 TX Manuel utilisateur

Viessmann

Viessmann VITOPLEX 300 Mode d'emploi

Viessmann

Viessmann Vitodens 100 Manuel utilisateur

Viessmann

Viessmann Vitocrossal Mode d'emploi

Viessmann

Viessmann VITOTRONIC 300-K Manuel utilisateur

Viessmann

Viessmann VITOLADENS 300-T Mode d'emploi

Viessmann

Viessmann Vitorond 100 Manuel d'instructions

Viessmann

Viessmann Vitotron 100 Mode d'emploi

Viessmann

Viessmann VITOFLEX 300-UF Manuel utilisateur

Viessmann

Viessmann Vitodens 300 Mode d'emploi

Viessmann

Viessmann Vitodens 100-W WB1B Series Guide rapide

Viessmann

Viessmann VITOCELL 100-B Mode d'emploi

Viessmann

Viessmann VITOLADENS 300-W Mode d'emploi

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur

Radiant

Radiant R2K 55 Manuel