Viessmann VITOCELL-V 100 Manuel utilisateur

VITOCELL-V 100

Installation Instructions

Vitocell 100

CVA Series

Enameled indirect-fired domestic hot water storage tank

42 to 120 USG / 160 to 450 ltr ca acity

THE HEAT TRANSFER

MEDIUM MUST BE WATER

OR OTHER NON-TOXIC

FLUID HAVING A TOXICIT

RATING OR CLASS OF 1,

AS LISTED IN CLINICAL

TOXICOLOG OF

COMMERCIAL PRODUCTS,

5TH EDITION.

THE PRESSURE OF THE

HEAT TRANSFER MEDIUM

MUST BE LIMITED TO A

MAXIMUM OF

30 PSIG B AN APPROVED

SAFET OR RELIEF VALVE

(SEE PAGE 2).

CAUTION

Read and save these instructions

for future reference.

IMPORTANT

42 to 79 USG / 160 to 300 ltr

ca acity

120 USG / 450 ltr ca acity

IN BOILER APPLICATIONS:

5167 519 v2.2 02/2009

Please file in Service Binder

Safety, Installation and Warranty Requirements

Please ensure that this manual is read and understood before commencing installation. Failure to comply with the issues listed below

and details rinted in this manual can cause product/property damage,severe personal injury, and/or loss of life. Ensure all

requirements below are understood and fulfilled (including detailed information found in manual subsections).

HLicensed professional heating

contractor

The installation, adjustment, service,

and maintenance of this equi ment

must be erformed by a licensed

rofessional heating contractor.

Please see section

entitled “Important

Regulatory and

Installation

Requirements”.

HProduct documentation

Read all applicable documentation

before commencing installation. Store

documentation near roduct in a

readily accessible location for

reference in the future by service

ersonnel.

For a listing of

applicable literature,

please see section

entitled “Important

Regulatory and

Installation Requirements”.

HAdvice to owner

Once the installation work is

com lete, the heating contractor must

familiarize the system

o erator/ultimate owner with all

equi ment, as well as safety

recautions/requirements, shut-down

rocedure, and the need for

rofessional service annually before

the heating season begins.

HWarranty

Information contained in

this and related roduct

documentation must be

read and followed. Failure

to do so renders warranty

null and void.

5167 519 v2.2

IN SOLAR

APPLICATIONS:

THE HEAT TRANSFER

MEDIUM MUST BE EITHER

POTABLE WATER OR

CONTAIN ONL

SUBSTANCES WHICH ARE

RECOGNIZED AS SAFE B

THE U.S. FOOD AND DRUG

ADMINISTRATION.

THE PRESSURE OF THE

HEAT TRANSFER MEDIUM

MUST BE MAINTAINED

LESS THAN THE NORMAL

MINIMUM OPERATING

PRESSURE OF THE

POTABLE WATER S STEM.

CAUTION

Contents

Page

Safety

Important Regulatory and Installation Requirements 4

.....

General Information

About these Instructions 5

.......................................................

Product Information 5

.................................................................

Set-up

Tank Set-up 6

...............................................................................

Recommended installation clearances for service

access 6

.........................................................................................

Minimum clearances to combustibles 6

................................

Multiple Tank Set-up 7

..............................................................

Connections

Orientation and Dimensions 8

..................................................

Installation of Inspection Opening Cover 8

...........................

DHW Tank Installation (42 to 79 USG /

160 to 300 ltr) 9

.........................................................................

DHW tem erature sensor installation 9

.................................

Aquastat installation 10

................................................................

Tem erature sensor installation for solar o eration 10

.......

Checking anode connections 11

................................................

DHW Tank Installation (120 USG / 450 ltr) 12

......................

Installation of thermal insulation 12

..........................................

DHW tem erature sensor installation 13

.................................

Aquastat installation 13

................................................................

Tem erature sensor installation for solar o eration 14

.......

Checking anode connections 15

................................................

Boiler Water/Solar Loop Connections 16

.................................

Individual DHW tank 16

...............................................................

Multi le DHW tanks 18

................................................................

Domestic Hot Water Connections 19

......................................

Recirculation Connections 21

.....................................................

Additional Information

Pressure Drop Information 22

....................................................

Post Installation ...

Start-u information 23

.................................................................

Service binder 23

...........................................................................

5167 519 v2.2

Safety

Important Regulatory and Installation Requirements

Codes

The installation of indirect-fired hot

water storage tanks might be governed

by individual local rules and regulations

for this ty e of roduct, which must be

observed. Always use latest editions of

codes.

Mechanical room

Ensure the mechanical room com lies

with the requirements of the technical

data manual.

The tank must be installed in a

mechanical room which is never subject

to freezing tem eratures.

If not in use and danger of freezing

exists in the mechanical room, ensure

water in tank is drained.

Please carefully read this manual prior

to attempting installation. Any

warranty is null and void if these

instructions are not followed.

his product must be installed

observing not only the necessary

product literature (see list below), but

also all local, provincial/state

plumbing and building codes, as they

apply to this product and all periphery

equipment.

For information regarding other

Viessmann System echnology

componentry, please reference

documentation of the respective

product.

We offer frequent installation and

service seminars to familiarize our

partners with our products. Please

inquire.

Working on the equipment

The installation, adjustment, service,

and maintenance of this equi ment

must be done by a licensed professional

heating contractor who is qualified and

ex erienced in the installation, service,

and maintenance of hot water heating

systems. There are no user serviceable

arts on this equi ment.

Ensure main power su ly to

equi ment, the heating system, and all

external controls has been deactivated.

Close main oil or gas supply valve. Take

recautions in all instances to avoid

accidental activation of ower during

service work.

he completeness and functionality of

field supplied electrical controls and

components must be verified by the

heating contractor. hese include low

water cut-offs, flow switches (if used),

staging controls, pumps, motorized

valves, air vents, thermostats,

temperature controls, etc.

Technical literature

Literature a licable to all as ects of

the Vitocell:

- Technical Data Manual

- Installation Instructions

- Start-u /Service Instructions

- O erating Instructions

and User’s Information Manual

Leave all literature at the installation

site and advise the system

operator/ultimate owner where the

literature can be found. Contact

Viessmann for additional copies.

5167 519 v2.2

If the heating system itself is to be

filled with Glycol or any other

antifreeze, the system fill must be of

non-toxic or food grade antifreeze. In

any circumstance, a non-toxic fluid

must be used. Ensure a copy of the

Material Safety Data Sheet (MSDS) is

supplied to the operator/ultimate

owner of the system.

WARNING

General Information

About These Instructions

Take note of all symbols and notations intended to draw attention to potential hazards or important product information.

These include ”WARNING”, ”CAUTION”, and ”IMPORTANT”. See below.

Warnings draw your attention to the

presence of potential hazards or

important product information.

Cautions draw your attention to the

presence of potential hazards or

important product information.

Helpful hints for installation, operation

or maintenance which pertain to the

product.

his symbol indicates that additional,

pertinent information is to be found in

column three.

his symbol indicates that other

instructions must be referenced.

Product Information

42 to 120 USG / 160 to 450 ltr ca acity

Enameled indirect-fired domestic hot water storage tank with one heat exchanger

coil for use with hot water heating boilers.

5167 519 v2.2

Indicates an imminently hazardous

situation which, if not avoided, could

result in death, serious injury or

substantial product/property damage.

WARNING

Indicates an imminently hazardous

situation which, if not avoided, may

result in minor injury or

product/property damage.

CAUTION

IMPORTANT

Set-u

Tank Set-up

HFor narrow assageways, remove

u er and lower ortion of crating and

carry DHW tank to its installation

location by means of crating boards

mounted on the tank.

HPosition tank carefully and remove

wood crating.

HLocate tank(s) on flooring or

foundation ca able of su orting the

weight of the tank(s) filled with

water.

HThe tank does not require a s ecial

foundation and can be laced directly

on the floor. If, for cleanliness

ur oses, the tank is to be ke t off

the floor, a foundation for each tank

or tank battery can be used.

HLevel tank using leveling bolts on tank

frame.

Recommended installation clearances for service access

Storage capacity USG

ltr

160

200

300

120

450

Rear inches

460

Sides May be reduced if rear i e

connections can be reached with

less clearance

inches

300

Top inches

900

1200

Front inches

600

Minimum clearances to combustibles

Storage capacity USG

ltr

160

200

300

120

450

All sides inches

Floor Combustibles

5167 519 v2.2

Fig 1.

Leveling bolt

min. ¾” / 20 mm

max. 1½” / 35 mm

Set-u

Multiple Tank Set-up

only for 79 and 120 USG / 300 and 450 ltr capacity

Two tanks, each with 79 USG / 300 ltr content, or up to four tanks, each with 120

USG / 450 ltr content, may be installed side-by-side.

he tank battery is controlled via one DHW tank aquastat making control of

individual tanks within the tank battery impossible.

If control of individual tanks within a battery is necessary, two alternatives exist.

Either a 4-tank battery needs to be separated into smaller batteries i.e. two

batteries each consisting of two tanks (one DHW tank aquastat controls each

battery), or all tanks should be installed individually i.e. individual tank set-up (one

DHW tank aquastat controls each tank).

Domestic hot water su ly

and T&P valve connection

Recirculation ta ing

Boiler/solar water su ly

O erating aquastat

Boiler/solar water return

Domestic cold water

Drain

Air vent

1. Install aquastat in the boiler water

su ly of the last tank receiving the

boiler water of the tank battery (see

illustration).

2. Install domestic cold and hot water

header lines (see illustration).

3. Install boiler/solar water su ly and

return header lines (see illustration).

4. Make final cold and hot water

connections.

Both the boiler/solar supply/return header

and the domestic hot/cold water header

must be installed in a reverse return

method. This ensures uniform heating of

all tanks in the battery. Header sizes for

batteries up to four 79 to 120 USG / 300

450 ltr tanks are printed on page 8.

5. Insulate header i ing lines.

5167 519 v2.2

Fig 2.

Installing multiple tanks in a battery

YY Y Y

IMPORTANT

In commercial installations, we

recommend the installation of an

additional high limit aquastat in the

main discharge pipe of domestic hot

water from the tank battery into the

system, and to wire this additional

high limit aquastat in series with the

operating aquastat.

CAUTION

ConnectionsConnections

Orientation and Dimensions

Storage capacity USG

ltr

42 and 53

160 and 200

300

120

450

Number of tanks 1121234

Layout

Connections (individual tank)

Heating water su ly / return

Domestic cold / hot water

Recirculation ta ing

∅”

Ground terminal

Domestic hot water su ly and

T&P valve connection

Recirculation ta ing

Aquastat well / sensor well

Boiler water su ly / solar su ly

Boiler water return / solar return

Domestic cold water su ly

Installation of Inspection Opening Cover

only for 42 to 79 USG / 160 to 300 ltr capacity

1.Insert insulation blanket.

2. Secure lastic cover with su lied

mounting bolts.

5167 519 v2.2

Fig 3.

DHW tank connections

(42 to 79 USG / 160 to 300 ltr)

Fig 4.

DHW tank connections

(120 USG / 450 ltr)

Fig 5.

Connections

DHW Tank Installation (42 to 79 USG / 160 to 300 ltr)

DHW temperature sensor installation

1. Mount sensor on the outside of the

sensor s ring-cli (not in the center

groove) so that it is flush with the

front of the sensor s ring-cli .

2. Sna sensor cabling into lastic cli

of sensor mounting equi ment.

3. Com letely insert sensor mounting

hardware along with sensor into

sensor well.

4. Remove to anel and insulation

blanket.

5. Remove ca from thermometer

o ening.

6. Slide thermometer sensor cable

through thermometer o ening in the

anel and insert thermometer.

7. Com letely insert sensor into metal

cli on flange.

8. For a lications with Vitotronic 100

control, use su lied lastic cli and

two screws to secure Honeywell bulb

ca illary. For a lications with the

Vitotronic 200 or 300 control o tion,

use su lied lastic cli and two

screws to secure sensor cable to

the tank sheet metal.

9. For Solar Domestic Hot Water with

Vitosolic 200, SCU124 or SCU 224,

use su lied lastic cli and two

screws to secure sensor cable to

the tank sheet metal.

Fig 6.

Sensor installation

5167 519 v2.2

Never wrap sensor with any type of

tape or insulation.

CAUTION

Connections

DHW Tank Installation (42 to 79 USG / 160 to 300 ltr)

(continued)

Aquastat installation

Where a Vitotronic 100 and a

Viessmann Power/Pum Control Module

(accessory) is utilized to control DHW

roduction:

1. Insert the extended ca illary of the

aquastat (su lied with Viessmann

Power/Pum Control Module, not

illustrated) fully and com letely into

sensor well. Mount aquastat

incons icuously on tank anelling.

Follow instructions in Fig 6. with

regard to sensor and s ring cli

installation.

The aquastat is to be mounted remote

from the tank well as follows:

2. Align sensor bulb with s ring cli .

3. Slide assembly into well.

4. The retention s ring cli must ress

the bulb ro erly to ensure surface

contact with the well.

Temperature sensor installation for solar operation

he temperature sensor for solar operation is included in the solar control unit package.

1. For solar o eration, install the sensor

well into the brass elbow and

connect the assembly to the heating

return line (solar return).

The brass elbow with sensor well is

available as an accessory,

Part No. 7175 213.

2. Insert the tem erature sensor until it

bottoms out inside the sensor well.

Never wrap insulating tape around the

sensor.

Fig 7.

Aquastat installation

5167 519 v2.2

Installation of temperature

sensor for solar operation

Fig. 8.

IMPORTANT

Autres manuels pour VITOCELL-V 100

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Viessmann Chaudière

Viessmann

Viessmann VITOCROSSAL 200 Manuel utilisateur

Viessmann

Viessmann VITOFLEX 300-UF Mode d'emploi

Viessmann

Viessmann B2HA 19 Manuel utilisateur

Viessmann

Viessmann Vitodens 200-W System Guide rapide

Viessmann

Viessmann Vitoflex 300-UF 390 Guide d'installation et d'utilisation

Viessmann

Viessmann Vitodens 222-W B2LB Manuel utilisateur

Viessmann

Viessmann Vitodens 100-W B1HA 26 Guide rapide

Viessmann

Viessmann VITODENS 200 Manuel utilisateur

Viessmann

Viessmann Vitocell 100-E Guide rapide

Viessmann

Viessmann VITOCAL 200-G Guide rapide

Viessmann

Viessmann VITOCELL 300B Mode d'emploi

Viessmann

Viessmann Vitoflame 100 Mode d'emploi

Viessmann

Viessmann VITOCELL 300B Mode d'emploi

Viessmann

Viessmann VITODENS 200-W B2HE 85 Guide de dépannage

Viessmann

Viessmann Vitodens 200-W B2HA series Manuel utilisateur

Viessmann

Viessmann Vitoligno 250-S Manuel utilisateur

Viessmann

Viessmann VITOCROSSAL 300 Manuel utilisateur

Viessmann

Viessmann VR2 Series Manuel utilisateur

Viessmann

Viessmann VITODENS 200-W WB2B 80 Manuel utilisateur

Viessmann

Viessmann Vitoplus 300 Mode d'emploi

Viessmann

Viessmann VITODENS Guide de démarrage rapide

Viessmann

Viessmann VITOCELL 100-VH Manuel d'instructions

Viessmann

Viessmann Vitodens 200-W WB2B Series Mode d'emploi

Viessmann

Viessmann Vitodens 242-F Guide de démarrage rapide

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur

Radiant

Radiant R2K 55 Manuel