Vertiv Liebert ITA2 Manuel utilisateur

Vertiv | Liebert®ITA2™, 8-10kVA, 208/220V Three-Phase UPS Quick-Start Guide | Rev. 0 | 01/18 | 1

LIEBERT®ITA2™UPS

Quick-Start Guide—60Hz, 208V, 8-10kVA

The complete Liebert ITA2 UP user manual is available at Vertiv’s Web site,

www.vertivco.com/en-us/products-catalog/critical-power/uninterruptible-power-

supplies-ups/ or by using the QR code at right.

Unpacking and Inspection

Unpack and inspect the UPS and its accessories,

shown at right

1. If any problem is found, file a damage claim with the

carrier immediately and send a copy to Vertiv at:

Vertiv

1050 Dearborn Drive

P.O. Box 29186

Columbus, Ohio 43085 USA

2. Check the accessories and models against the

delivery list. If any problem is found, notify your local

Vertiv representative immediately.

Single-Input Configuration

1. Remove the conduit box cover to gain access to the

input and output terminal blocks.

2. Remove the knockout plates and attach the

conduits to the rear of the conduit box.

Hardwire Connections—UPS Input

3. Leave the shorting busbars in place on the UPS

input terminal block.

4. Using Figure 1, make these connections:

• Phase A cable from the upstream feeder panel

to UPS Jumper 11

• Phase B cable from the upstream feeder panel

to UPS Jumper 12

• Phase C from the upstream feeder panel to

UPS Terminal 13

• Neutral from the upstream feeder panel to UPS

Terminal 14 or 15

• The safety equipment ground cable from

upstream feeder panel to UPS ground stud 10

Hardwire Connections—UPS Output

The UPS has two output terminal block sections, one is always on and the other is programmable/controllable.

These instructions will list the always-on connections first, followed by the programmable connections inside

parentheses.

1. Using Figure 1, make these connections:

• Phase A cable from UPS Terminal 4 (9) to the downstream distribution panel Phase A on the panelboard main breaker

• Phase B cable from UPS Terminal 3 (8) to the downstream distribution panel Phase B on the panelboard main breaker

• Phase C cable from UPS terminal 2 (7) to the downstream distribution panel Phase C on the panelboard main breaker

• Neutral cable from UPS terminal 5 (6) to the downstream distribution panel neutral bus

• The safety equipment ground cable from UPS Ground Stud 1 to the downstream distribution panel ground bus

2. Replace the conduit box cover and secure it.

Corner

Braces

Protective

Packing

Protective

Packing

Bag of

Hardware

Front

Panel

Liebert ITA2

Support

Base

Liebert ITA2 and Accessories as Shipped

Vertiv | Liebert®ITA2™, 8-10kVA, 208/220V Three-Phase UPS Quick-Start Guide | Rev. 0 | 01/18 | 2

Figure 1 Wiring diagram—Single-input configuration

Dual-Input Configuration

Dual input configuration for the UPS requires that both feeds be from the same source.

1. Remove the conduit box cover to gain access to the input and output terminal blocks.

2. Remove the knockout plates and attach the conduits to the rear of the conduit box.

Dual-Input Hardwire Connections—Main Input

3. Remove the shorting busbars from the UPS input terminal block on Terminals 11, 12 and 13

Dual-Input Hardwire Connections—UPS Rectifier Input

4. With the shorting busbars removed from the UPS input terminal block, using Figure 2, make these connections:

• Phase A cable from the upstream feeder panel to UPS Terminal 11

• Phase B cable from the upstream feeder panel to UPS Terminal 13

• Phase C from the upstream feeder panel to UPS Terminal 15

• Neutral from the upstream feeder panel to UPS Terminal 17

• The safety equipment ground cable from the upstream feeder panel to UPS ground stud 10.

1. PE: Output PE Terminal 2. C: AC Output Terminal Phase C 3. B: AC Output Terminal Phase B

4. A: AC Output Terminal Phase A 5. N: Output Neutral Line Terminal 6. N: Output Neutral Line Terminal

7. pC: AC Output Terminal Phase C 8. pB: AC Output Terminal Phase B 9. pA: AC Output Terminal Phase A

10. PE: Output PE Terminal. 11. L1: Input Line Phase A 12. L2: Input Line Phase B

13. L3: Input Line Phase C 14. N: Input Neutral Line Terminal 15. N: Input Neutral Line Terminal

16. BAT+: Battery Positive Terminal 17. BATN: Battery Neutral Terminal 18. BAT-: Battery Negative Terminal

19. PE: Battery PE Terminal

Table 1 Shorting copper bar

Bypass Shorting Copper Bar Drawing

2-Pin Copper Bar

1234 56 789 10

12131415161718 11

Vertiv | Liebert®ITA2™, 8-10kVA, 208/220V Three-Phase UPS Quick-Start Guide | Rev. 0 | 01/18 | 3

Dual-Input Hardwire Connections—UPS Bypass Input

5. With the shorting busbars removed on the UPS input terminal block, using Figure 2, make these connections:

• Phase A cable from the upstream feeder panel to UPS Terminal 12

• Phase B cable from the upstream feeder panel to UPS Terminal 14

• Phase C from the upstream feeder panel to UPS Terminal 16

• Neutral from the upstream feeder panel to UPS Terminal 18

• The safety equipment ground cable from the upstream feeder panel to UPS Ground Stud 10.

Dual-Input Hardwire Connections—UPS Output

The UPS has two output terminal block sections, one is always on and the other is programmable/controllable.

These instructions will list the always-on connections followed by the programmable connections inside

parentheses.

6. Using Figure 2, make these connections:

• Phase A cable from UPS Terminal 4 (9) to the downstream distribution panel Phase A on the panelboard main breaker

• Phase B cable from UPS Terminal 3 (8) to the downstream distribution panel Phase B on the panelboard main breaker

• Phase C cable from UPS Terminal 2 (7) to the downstream distribution panel Phase C on the panelboard main breaker

• Neutral cable from UPS Terminal 5 (6) to the downstream distribution panel neutral bus

• The safety equipment ground cable from UPS Ground Stud 1 to the downstream distribution panel ground bus

7. Replace the conduit box cover and secure it.

Figure 2 Wiring diagram—Dual input configuration

Install Auxiliary Equipment

If the installation will include a Liebert ITA2 Maintenance Bypass Cabinet or Liebert ITA2 Battery Cabinet, refer to

the quick start guides or user manuals to install those units.

The UPS startup procedures can be performed after the installation is finished and the external input MBC’s are

closed.

1. PE: Output PE Terminal 2. C: AC Output Terminal Phase C 3. B: AC Output Terminal Phase B

4. A: AC Output Terminal Phase A 5. N: Output Neutral Line Terminal 6. N: Output Neutral Line Terminal

7. pC: AC Output Terminal Phase C 8. pB: Programmable AC Output Terminal Phase B 9. pA: Programmable AC Output Terminal Phase A

10. PE: Input PE Terminal. 11. rA: AC Rectifier Input Phase A 12. bA: Bypass Input Phase A

13. rB: AC Rectifier Input Phase B 14. bB: Bypass Input Phase B 15. rC: AC Rectifier Input Phase C

16. bC: Bypass Input Phase C 17. N: Input Neutral Line Terminal 18. N: Input Neutral Line Terminal

19. BAT+: Battery Positive Terminal 20. BATN: Battery Neutral Terminal 21. BAT-: Battery Negative Terminal

22. PE: Battery PE Terminal.

1234 56789 10

12131415161718 11

2021

Vertiv | Liebert®ITA2™, 8-10kVA, 208/220V Three-Phase UPS Quick-Start Guide | Rev. 0 | 01/18 | 4

Initial Startup

When the UPS is first started, the interfaces below will appear to guide in setting basic parameters At the

Welcome Screen, press the Enter button to start the guide...

names, trademarks or registered trademarks of their respective owners.

While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and disclaims all liability, for damages resulting

from use of this information or for any errors or omissions. Specifications are subject to change without notice.

Enter

Welcome Screen Language, Date and Time

Battery Parameters Screen

(Default is 32)

Output Voltage and Frequency Screen

Finish Screen

Click Finish at the final guidance screen

to enter the UPS Mimic Screen. The UPS

will begin normal operation.

Technical Support Three-Phase UPS & Power Systems

800-543-2378

Outside North America: 614-841-6598

United States

SL-26255QS_REV0_01-18

1050 Dearborn Drive

P.O. Box 29186

Columbus, OH 43085

www.vertivco.com

Autres manuels pour Liebert ITA2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vertiv UPS

Vertiv

Vertiv Liebert GXTRT-1000IRT2UXL Manuel utilisateur

Vertiv

Vertiv LIEBERT PSI5 Series Guide de l'utilisateur

Vertiv

Vertiv Liebert PST5 Series Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert EXM2 Manuel utilisateur

Vertiv

Vertiv Liebert PSI PS2200RT3-120 Manuel utilisateur

Vertiv

Vertiv Liebert GXT3 Series Instructions d'installation et d'entretien

Vertiv

Vertiv Avocent HMXCC1-G2 Manuel utilisateur

Vertiv

Vertiv Liebert EXS 80kVA UPS Manuel utilisateur

Vertiv

Vertiv Liebert NX 225 kVA Manuel utilisateur

Vertiv

Vertiv Liebert ITA2 Manuel utilisateur

Vertiv

Vertiv Liebert GXT5-5000MVRT4UXLN Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert Trinergy Cube Mode d’emploi

Vertiv

Vertiv Liebert GXT RT+ Series Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert NXL Manuel utilisateur

Vertiv

Vertiv Liebert PSI XR 1000 Manuel utilisateur

Vertiv

Vertiv LIEBERT PSA itON-SOHO Manuel utilisateur

Vertiv

Vertiv Liebert NXL Manuel utilisateur

Vertiv

Vertiv Liebert PSA Manuel utilisateur

Vertiv

Vertiv Liebert EXS Manuel utilisateur

Vertiv

Vertiv Liebert PSA Manuel utilisateur

Vertiv

Vertiv Liebert ITA2 Manuel utilisateur

Vertiv

Vertiv Liebert PST4-660MT120 Instructions d'installation et d'entretien

Vertiv

Vertiv Liebert EXS 0030kTH16FN01000 Manuel utilisateur

Vertiv

Vertiv Liebert MicroPOD Instructions d'installation et d'entretien

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur