Vaisala GMD20 Manuel utilisateur

CO2transmitter GMD20 and GMD20D M210292en-A

INTRODUCTION

Vaisala’s GMD20 uses silicon based CARBOCAPsensor technology providing

excellent stability and reliability. The GMD20 transmitters require almost no

maintenance: the recommended calibration interval is five years in HVAC and related

benign applications. Transmitters are available without a display (GMD20 version) and

with a display (GMD20D version).

MOUNTING

The GMD20 transmitters are truly duct mounted. The distance between the probe and the

duct wall is easily adjusted by using the mounting plate. The mounting plate is fastened

with four screws ST.4.2x16-C-Z/A4m DIN 7981. Note that four ∅3.2 holes on the duct

surface are needed, as well as one ∅22...25 mm hole in the middle (see figure below).

Insert the transmitter through the mounting plate and adjust the distance.

Figure 1 Dimensions of the GMD20 and the mounting plate (in mm)

ELECTRICAL CONNECTIONS

Open the transmitter cover and remove the display board if there is one installed. The

cable is inserted through a rubber plug included in the package. Pierce the rubber plug

with a screwdriver or a similar instrument in order to open the hole for the cable. Then

insert the plug in the appropriate hole in the transmitter cover. Strip a few millimetres of

the cable insulation and insert the cable carefully through the rubber plug so that you can

connect the wires to the terminal block on the righthand side of the component board.

min 80 max 140

Ø15

The nominal 24 V supply must be connected between terminals + and -. The analogue

output is available at remaining terminals. The common wire is connected to terminal 0

and the other wire either to terminal V (voltage output) or to terminal mA (current

output). The current output type is chosen with the jumper 0/4mA (see Figure 2):

4...20mA is chosen by connecting the jumper (default) and the 0...20 mA is chosen by

disconnecting the jumper. If the relay output of the display board (in GMD20D ) is used,

connect the wires to the terminal block at the back of the display board before re-

installing it. The default relay trigger point has been set to 1000 ppm and it can be

changed with the optional software kit 19222GM. For further details, contact your local

Vaisala representative. If an optional LonWorks interface or a relay output option is

installed in the GMD20, please, refer to the corresponding manuals for details.

Note that during normal operation the green led (V10) at the lower righthand corner is

blinking. In case the self-diagnostics procedure comes across some abnormality, the red

led (V7) lights up (see Figure 2).

Figure 2 Electrical connections and leds V7, V10

SERVICE AND MAINTENANCE

The GMD20 transmitters have an excellent stability and require almost no maintenance.

In benign environments the recommended calibration interval is five years. If the reading

differs too much from the reference value during checking, the transmitter should be

removed and preferably sent to Vaisala or Vaisala distributor for re-calibration. In case

the user prefers to do the re-calibration himself, Vaisala's software Kit 19222GM and

accurate calibration gases are needed.

If full accuracy is required, the transmitter has to be calibrated against accurate and

traceable calibration gases in stable environmental conditions (temperature, pressure).

Accurate calibrations are usually performed in laboratories; in these calibrations,

temperature and pressure corrections have to be made. A full after sales calibration and

service facility is naturally provided by Vaisala and its distributors. For further details,

consult your local Vaisala representative.

CO2transmitter GMD20 and GMD20D M210292en-A

POWER SUPPLY REQUIREMENTS

The GMD20 transmitter is designed to operate from a nominal 24 VAC/VDC supply. The

power supply should maintain the voltage between 18...30 VDC or 20...26 VAC for all

load conditions and all mains voltages. The power input includes a halfwave rectifier. To

avoid current peaks, it is recommended to use a DC supply. The average transmitter cur-

rent consumption is 85 mA maximum but peak currents of 170 mA may occur during

normal operation.

CONNECTION TO A 24 VAC SUPPLY

The GMD20 transmitters can also be connected to a 24 VAC supply without an external

rectifier. However, when more than one transmitter is connected to one 24 VAC

transformer, a common loop is formed and there is an increased risk of a short-circuit. To

avoid this, always use separate floating supply for each transmitter (see Figure 3A).

However, if several transmitters have to share one transformer, the phase (∼) must always

be connected to + connector in each transmitter (see Figure 3B).

Figure 3 AC connections

24V OUT

GND

24V OUT

GND

CONTROLLER

GM20

Signal

output

Signal

output

Supply

voltage

Supply

voltage

24VAC

GM20

24V OUT

GND

24V OUT

GND

Signal

output

Signal

output

Supply

voltage

Supply

voltage

SHARED

COMMON

LINE

GM20

CONTROLLER

24VAC

CO2transmitter GMD20 and GMD20D M210292en-A

TECHNICAL DATA

Carbon dioxide

Measuring range 0...2000 ppm CO2(nominal); with recalibration 0...5000 ppm CO2,

0...10 000 ppm CO2, 0...20 000 ppm CO2

Accuracy at 20°C against

certified factory references <±[30 ppm + 2.0 % of the reading]

(including repeatability and calibration uncertainty)

Non-linearity <±1.0 %FS

Temperature dependence

of output (typical) < 0.15 %FS / °C (reference 25°C)

Long-term stability <±5 %FS / 5 years

Response time (0…63%) 1 minute

Operating conditions

Operating temperature -5...+45 °C

Storage temperature -20...+70 °C

Humidity range short term 0...85 %RH (non-condensing)

Air flow range 0...10 m/s

General

Analogue outputs 0...20 mA or 4...20 mA and 0...10 V

Resolution of analog outputs 0.5 % FS

Recommended external load:

current output max. 500 Ω

voltage output min. 1kΩ

Relay contact ratings max. 50 V 0.5 A

Power supply nominal 24 VDC/VAC (18...30 VDC)

Power consumption < 2.5 W average

Warm-up time < 15 minutes

Mechanics

Housing material ABS plastic

Housing classification IP65

(electronics housing)

Weight:

GMD20 140 g

GMD20D 170 g

ACCESSORIES

Order code Description

GMR20 Relay output option (not for the GMD20D)

GML20 LonWorksinterface option (not for the GMD20D )

GM35001 Calibration pipe

19222GM Calibration software kit (incl. disk and serial COM adapter)

GUARANTEE

Vaisala issues a guarantee for the material and workmanship of this product under

normal operating conditions for one (1) year from the date of delivery. Exceptional

operating conditions, damage due to careless handling and misapplication will void

the guarantee.

CO2transmitter GMD20 and GMD20D M210292en-A

210292

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vaisala Émetteur

Vaisala

Vaisala HUMICAP DMT132 Manuel utilisateur

Vaisala

Vaisala DPT145 Manuel utilisateur

Vaisala

Vaisala Indigo 202 Manuel utilisateur

Vaisala

Vaisala HUMICAP HMD70U Manuel utilisateur

Vaisala

Vaisala HMD60 Series Manuel utilisateur

Vaisala

Vaisala Spectracap OMT355 Manuel utilisateur

Vaisala

Vaisala HUMICAP HMT140 Manuel utilisateur

Vaisala

Vaisala WXT510 Manuel utilisateur

Vaisala

Vaisala HUMICAP HMT310 Manuel utilisateur

Vaisala

Vaisala TMI110 Manuel utilisateur

Vaisala

Vaisala HUMICAP HMT120 Series Manuel utilisateur

Vaisala

Vaisala PDT101 Manuel utilisateur

Vaisala

Vaisala HUMICAP MMT310 Manuel utilisateur

Vaisala

Vaisala MHT410 Manuel utilisateur

Vaisala

Vaisala HUMICAP HMI41 Manuel utilisateur

Vaisala

Vaisala GMW95 Manuel utilisateur

Vaisala

Vaisala Indigo300 Manuel utilisateur

Vaisala

Vaisala PTU200 Series Manuel utilisateur

Vaisala

Vaisala WXT510 Manuel utilisateur

Vaisala

Vaisala HUMICAP HMT330 SERIES Manuel utilisateur

Vaisala

Vaisala HUMICAP HMT360 SERIES Manuel d'installation et d'exploitation

Vaisala

Vaisala HUMICAP HMT120 Series Manuel utilisateur

Vaisala

Vaisala HUMICAP HMT360 SERIES Manuel utilisateur

Vaisala

Vaisala INTERCAP HMW82 Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur