Unitronics MJ20-MEM1 Manuel utilisateur

Unitronics 1

MJ20-MEM1 Installation Guide & Technical Specifications

Program Cloner Add-on Module

Before using this product, the user must read and understand this document.

For additional information regarding this product, refer to the Jazz™user guide.

All examples and diagrams are intended to aid understanding, and do not guarantee operation.

Unitronics accepts no responsibility for actual use of this product based on these examples.

Please dispose of this product according to local and national standards and regulations.

Only qualified service personnel should open this device or carry out repairs.

Failure to comply with appropriate safety guidelines can cause severe injury or property damage.

Do not attempt to use this device with parameters that exceed permissible levels.

Environmental Considerations

Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,

moisture or rain, excessive heat, regular impact shocks or excessive vibration.

Do not place in water or let water leak onto the unit.

Do not allow debris to fall inside the unit during installation.

About the Program Cloner Add-on Module

The Program Cloner enables you to copy applications between Jazz™OPLCs™. You plug the

Cloner into the jack of a Jazz OPLC and then use Info Mode to:

Copy the complete application, including the PLC Ladder program, HMI application, and OS

into the Cloner. In addition, you can also copy certain current application values. You can

find a list of these values in the Jazz user guide.

Plug the Cloner into another Jazz OPLC and download the complete application

Installation and Removal

1. Remove the cover from the Jazz jack as shown in the first two figures below.

2. Position the Cloner so that the Cloner’s pin receptacles are aligned with the pins in the

Jazz jack as shown in the third figure below.

3. Gently slide the port into the jack until it snaps into place.

4. To remove the port, slide it out, and then re-cover the Jazz jack.

4/06 MJ20-MEM1

DIP Switch

There are two switches on the Cloner.

1: - ON enables you to both read from and write to the Cloner

- OFF enables you to apply write protection. This enables read-only

2: This switch is for factory use only. It is set in the ON position. Do not move it.

Read Only

Internal use only

Keep ON

Read / Write

MJ20-MEM1 Technical Specifications

Memory

Memory type Flash

Environmental

Operating temperature 0°to 50°C (32°to 122°F)

Storage temperature -20°to 60°C (-4°to 140°F)

Relative Humidity (RH) 10% to 95% (non-condensing)

Dimensions

71 mm (2.795") 20 mm (0.787")

38 mm (1.496")

Weight 24g (0.85oz.)

Київ

тел. +38 044 495 33 40

[email protected].ua

Самара

тел. +7 846 273 95 85

[email protected]

Москва

тел. +7 495 641 1616

[email protected]

Екатеринбург

тел. +7 343 287 19 19

yekat[email protected]

Санкт-Петербург

тел. +7 812 327 3752

[email protected]

Rīga

tel. +371 6738 1617

[email protected]

Helsinki

puh. +358 9 540 4940

automation@klinkmann.

Tallinn

tel. +372 668 4500

[email protected]

Vilnius

tel. +370 5 215 1646

[email protected]

Минск

тел. +375 17 2000 876

[email protected]

www.klinkmann.ru

mj20-mem1_spec_04-06_en_1215

Autres manuels Unitronics Contrôleurs

Unitronics

Unitronics Jazz OPLC JZ20-R10 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V130-J-B1 Manuel utilisateur

Unitronics

Unitronics V230 Manuel utilisateur

Unitronics

Unitronics UniStream USC-B5-TA32 Manuel utilisateur

Unitronics

Unitronics Vision V350-35-T2 Manuel utilisateur

Unitronics

Unitronics UniStream 5 inch Manuel utilisateur

Unitronics

Unitronics Vision OPLC V130-33-TA24 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V350-35-TR20 Manuel utilisateur

Unitronics

Unitronics Vision V120 Manuel utilisateur

Unitronics

Unitronics UniStream USC-B5-B1 Manuel utilisateur

Unitronics

Unitronics UniStream USC-B10-RA28 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V1040-T20B Manuel utilisateur

Unitronics

Unitronics UniStream PLC Series Manuel utilisateur

Unitronics

Unitronics Uni-COM UAC-CB-01RS2 Manuel utilisateur

Unitronics

Unitronics Samba OPLC SM43-J-R20 Manuel utilisateur

Unitronics

Unitronics Samba OPLC SM43-J-R20 Manuel utilisateur

Unitronics

Unitronics MJ20-MEM1 Manuel utilisateur

Unitronics

Unitronics Vision OPLC V1040-T20B Manuel utilisateur

Unitronics

Unitronics UniStream USC-C3-R20 Manuel utilisateur

Unitronics

Unitronics UniStream Built-in Series Manuel utilisateur

Unitronics

Unitronics Vision700 Manuel utilisateur

Unitronics

Unitronics UniStream USC-B5-R38 Manuel utilisateur

Unitronics

Unitronics Vision V130-J Series Manuel utilisateur

Unitronics

Unitronics Samba SM70-J-RA22 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur