Unit UPO1000 Series Manuel utilisateur

Quick Guide

UPO1000 Series Digital Phosphor Oscilloscope

Quick Guide UPO1000 Series

2/17

Trademark

UNI-T is the registered trademark of Uni-Trend Technology (China) Co., Ltd.

File Version

20230822-V1.00.0018

Statement

UNI-T products are protected by patent rights in China and foreign countries, including issued and

pending patents.

UNI-T reserves the rights to any product specification and pricing changes.

UNI-T reserves all rights. Licensed software products are properties of Uni-Trend and its subsidiaries

or suppliers, which are protected by national copyright laws and international treaty provisions.

Information in this manual supersedes all previously published versions.

Technical data are subject to change without prior notice.

Quick Guide UPO1000 Series

3/17

1. Safety Requirements

This section contains information and warnings that must be followed to keep the instrument operating

under safety conditions. In addition, user should also follow the common safety procedures.

Safety Precautions

Warning

Please follow the following guidelines to avoid possible electric shock and risk to

personal safety.

Users must follow the following conventional safety precautions in operation,

service and maintenance of this device. UNI-T will not be liable for any personal

safety and property loss caused by the user’s failure to follow the following safety

precautions. This device is designed for professional users and responsible

organizations for measurement purposes.

Do not use this device in any way not specified by the manufacturer. This device is

only for indoor use unless otherwise specified in the product manual.

Safety Statement

Warning

“Warning” indicates the presence of a hazard. It reminds users to pay attention to a

certain operation process, operation method or similar. Personal injury or death

may occur if the rules in the “Warning” statement are not properly executed or

observed. Do not proceed to the next step until you fully understand and meet the

conditions stated in the “Warning” statement.

Caution

“Caution” indicates the presence of a hazard. It reminds users to pay attention to a

certain operation process, operation method or similar. Product damage or loss of

important data may occur if the rules in the “Caution” statement are not properly

executed or observed. Do not proceed to the next step until you fully understand and

meet the conditions stated in the “Caution” statement.

Note

“Note” indicates important information. It reminds users to pay attention to

procedures, methods and conditions, etc. The contents of the “Note” should be

highlighted if necessary.

Safety Sign

Danger

It indicates possible danger of electric shock, which may cause

personal injury or death.

Warning

It indicates that you should be careful to avoid personal injury or

product damage.

Caution

It indicates possible danger, which may cause damage to this device

or other equipment if you fail to follow a certain procedure or

condition. If the “Caution” sign is present, all conditions must be met

before you proceed to operation.

Note

It indicates potential problems, which may cause failure of this device

if you fail to follow a certain procedure or condition. If the “Note” sign

is present, all conditions must be met before this device will function

properly.

Alternating current of device. Please check the region’s voltage range.

Direct current device. Please check the region’s voltage range.

Quick Guide UPO1000 Series

4/17

Grounding

Frame and chassis grounding terminal

Grounding

Protective grounding terminal

Grounding

Measurement grounding terminal

OFF

Main power off

Main power on

Power

Supply

Standby power supply: when the power switch is turned off, this

device is not completely disconnected from the AC power supply.

CAT I

Secondary electrical circuit connected to wall sockets through transformers or

similar equipment, such as electronic instruments and electronic equipment;

electronic equipment with protective measures, and any high-voltage and

low-voltage circuits, such as the copier in the office.

CAT II

CATII: Primary electrical circuit of the electrical equipment connected to the indoor

socket via the power cord, such as mobile tools, home appliances, etc. Household

appliances, portable tools (e.g. electric drill), household sockets, sockets more than

10 meters away from CAT III circuit or sockets more than 20 meters away from CAT

IV circuit.

CAT III

Primary circuit of large equipment directly connected to the distribution board and

circuit between the distribution board and the socket (three-phase distributor

circuit includes a single commercial lighting circuit). Fixed equipment, such as

multi-phase motor and multi-phase fuse box; lighting equipment and lines inside

large buildings; machine tools and power distribution boards at industrial sites

(workshops).

CAT IV

Three-phase public power unit and outdoor power supply line equipment.

Equipment designed to “initial connection”, such as power distribution system of

power station, power instrument, front-end overload protection, and any outdoor

transmission line.

Certific

ation

CE indicates a registered trademark of EU.

Certific

ation

UKCA indicates a registered trademark of the United Kingdom.

Certific

ation

It conforms to UL STD 61010-1, 61010-2-030, CSA STD C22.2 No.61010-1 and

61010-2-030.

Waste

This product complies with the marking requirements of WEEE Directive

(2002/96/EC). This additional label indicates that this electrical / electronic product

must not be discarded in household waste.

EFUP

This environment-friendly use period (EFUP) mark indicates that dangerous or toxic

substances will not leak or cause damage within this indicated time period. The

environment-friendly use period of this product is 40 years, during which it can be

used safely. Upon expiration of this period, it should enter the recycling system.

Safety Requirements

Warning

Quick Guide UPO1000 Series

5/17

Preparation

before use

Please connect this device to AC power supply with the power cable provided;

The AC input voltage of the line reaches the rated value of this device. See the

product manual for specific rated value.

The line voltage switch of this device matches the line voltage;

The line voltage of the line fuse of this device is correct;

Not use to measure the main circuit.

Check all

terminal rated

values

Please check all rated values and marking instructions on the product to avoid fire

and impact of excessive current. Please consult the product manual for detailed

rated values before connection.

Use the power

cord properly

You can only use the special power cord for the instrument approved by the local

and state standards. Please check whether the insulation layer of the cord is

damaged or the cord is exposed, and test whether the cord is conductive. If the cord

is damaged, please replace it before using the instrument.

Instrument

Grounding

To avoid electric shock, the grounding conductor must be connected to the ground.

This product is grounded through the grounding conductor of the power supply.

Please be sure to ground this product before it is powered on.

AC power supply

Please use the AC power supply specified for this device. Please use the power cord

approved by your country and confirm that the insulation layer is not damaged.

Electrostatic

prevention

This device may be damaged by static electricity, so it should be tested in the

anti-static area if possible. Before the power cable is connected to this device, the

internal and external conductors should be grounded briefly to release static

electricity. The protection grade of this device is 4KV for contact discharge and 8KV

for air discharge.

Measurement

accessories

Measurement accessories are of lower class, which are definitely not applicable to

main power supply measurement, CAT II, CAT III or CAT IV circuit measurement.

Probe assemblies and accessories within the scope of IEC 61010-031 and current

sensors within the scope of IEC 61010-2-032 shall meet their requirements.

Use the input /

output port of

this device

properly

Please use the input / output ports provided by this device in a properly manner. Do

not load any input signal at the output port of this device. Do not load any signal that

does not reach the rated value at the input port of this device. The probe or other

connection accessories should be effectively grounded to avoid product damage or

abnormal function. Please refer to the product manual for the rated value of the

input / output port of this device.

Power fuse

Please use power fuse of specified specification. If the fuse needs to be replaced, it

must be replaced with another one that meets the specified specifications by the

maintenance personnel authorized by UNI-T.

Disassembly and

cleaning

There are no components available to operators inside. Do not remove the

protective cover.

Maintenance must be carried out by qualified personnel.

Service

environment

This device should be used indoors in a clean and dry environment with ambient

temperature from 0 ℃- 40 ℃.

Do not use this device in explosive, dusty or humid air.

Do not operate

in humid

environment

Do not use this device in a humid environment to avoid the risk of internal short

circuit or electric shock.

Do not operate

in flammable

and explosive

environment

Do not use this device in a flammable and explosive environment to avoid product

damage or personal injury.

Caution

Quick Guide UPO1000 Series

6/17

Abnormality

If this device may be faulty, please contact the authorized maintenance personnel of

UNI-T for testing. Any maintenance, adjustment or parts replacement must be done

by the relevant personnel of UNI-T.

Cooling

Do not block the ventilation holes at the side and back of this device;

Do not allow any external objects to enter this device via ventilation holes;

Please ensure adequate ventilation, and leave a gap of at least 15 cm on both sides,

front and back of this device.

Safe

transportation

Please transport this device safely to prevent it from sliding, which may damage the

buttons, knobs or interfaces on the instrument panel.

Proper

ventilation

Poor ventilation will cause the device temperature to rise, thus causing damage to

this device. Please keep proper ventilation during use, and regularly check the vents

and fans.

Keep clean and

dry

Please take actions to avoid dust or moisture in the air affecting the performance of

this device. Please keep the product surface clean and dry.

Note

Calibration

The recommended calibration period is one year. Calibration should only be carried

out by qualified personnel.

1.1 Environmental Requirements

This instrument is suitable for the following environment:

Indoor use

Pollution degree 2

In operating: altitude lower than 3000 meters; in non-operating: altitude lower than 15000 meters

Unless otherwise specified, operating temperature is 0 to +40℃; storage temperature is -20 to﹢70℃

In operating, humidity temperature below to +35℃, ≤90％relative humidity;

In non-operating, humidity temperature +35℃to +40℃, ≤60％relative humidity

There are ventilation opening on the rear panel and side panel of the instrument. So please keep the air

flowing through the vents of the instrument housing. To prevent excessive dust from blocking the vents,

please clean the instrument housing regularly. The housing is not waterproof, please disconnect the power

supply first and then wipe the housing with a dry cloth or a slightly moistened soft cloth.

1.2 Connecting Power Supply

The specification of input AC power.

Voltage Range

Frequency

Maximum Power

100-240 VAC (fluctuant: ±10%)

50/60 Hz

75 W

100-120 VAC (fluctuant: ±10%)

400 Hz

Please use the attached power cable to connect to the power port.

Connecting to service cable

This instrument is a Class I safety product. The supplied power lead has good performance in terms of case

ground. This spectrum analyzer is equipped with a three-prong power cable that meets international safety

standards. It provides good case grounding performance for the specification of your country or region.

Quick Guide UPO1000 Series

7/17

Please install AC power cable as follows.

Ensure the power cable is in a good condition.

Leave enough space for connecting the power cord.

Plug the attached three-prong power cable into a well-grounded power socket.

1.3 Electrostatic Protection

Electrostatic discharge may cause damage to component. Components can be damaged invisibly by

electrostatic discharge during transportation, storage and use.

The following measure can reduce the damage of electrostatic discharge:

Testing in anti-static area as far as possible.

Before connecting the power cable to the instrument, inner and outer conductors of the instrument

should be briefly grounded to discharge static electricity.

Ensure all the instruments are properly grounded to prevent the accumulation of static.

Quick Guide UPO1000 Series

8/17

2. Introduction of UPO1000

UPO1000 series digital phosphor oscilloscope includes three models.

Model

Analog Bandwidth

Analog Channel

Sampling Rate

UPO1204

200 MHz

2 GSa/s

UPO1104

100 MHz

2 GSa/s

UPO1054

50 MHz

2 GSa/s

UPO1000 series digital phosphor oscilloscope adopts UNI-T 3D technique Ultra Phosphor 2.0 with new

appearance upgrade and the function of deep storage, high waveform capture rate, real-time

waveform recording and playback and 256-level grayscale display.

The series is equipped with three levels of bandwidth of 50 MHz/100 MHz/200 MHz, real-time sampling

rate up to 2 GSa/s. The whole series are equipped with 4 channels, the maximum storage depth is

56Mpts, up to 500,000wfms/s in Fast Acquire mode. Hardware real-time waveform uninterrupted

recording and waveform analysis up to 120,000 waveform frames; support DVM module, rich trigger

and bus decoding functions, and support full memory hardware real-time decoding.

It widely used in many fields, including communication, semiconductor, computer, IC design,

instrumentation, industrial electronics, consumer electronics, automotive electronics, field

maintenance and R&D/education.

Quick Guide UPO1000 Series

9/17

3. Getting Started Guide

This chapter is to introduce on using the oscilloscope for the first time, the front and rear panels, the user

interface, as well as the built-in help system.

3.1 General Inspection

It is recommended to inspect the instrument follow the steps below before using the UPO1000 series for

the first time.

(1) Check for Damages caused by Transport

If the packaging carton or the foam plastic cushions are severely damaged, please contact the UNI-T

distributor of this product immediately.

(2) Check Attachment

Please check appendix for the list of accessories. If any of the accessories are missing or damaged,

please contact UNI-T or local distributors of this product.

(3) Machine Inspection

If the instrument appears to be damaged, not working properly, or has failed the functionality test,

please contact UNI-T or local distributors of this product.

If the equipment is damaged due to shipping, please keep the packaging and notify both the

transportation department and UNI-T distributors, UNI-T will arrange maintenance or replacement.

3.2 Before Use

To perform a quick verification of the instrument’s normal operations, please follow the steps below.

(1) Connecting to the Power Supply

AC power specification of UPO1000 series digital storage oscilloscope refers to Connecting Power

Supply section. Use the assembled power line or other power line that meets the local country

standards to connect the oscilloscope. The power soft indicator in the left bottom on front

panel is extinguished and this soft switch key is no-effect when the power switch on rear panel is not

opened. The power soft indicator in the left bottom on front panel is illuminated with red and

then press the soft switch key to enable the oscilloscope.

(2) Boot Check

Press the soft power key and the indicator should change from red to green. The oscilloscope

will show a boot animation, and then enter the normal interface.

(3) Connecting Probe

Use BNC of the port to connect to BNC of CH1 of the oscilloscope. Connecting the probe to the “probe

compensation signal connection clip” and connecting the ground alligator clip to the “ground terminal”

under the “probe compensation signal connection clip”. The output of probe compensation signal

connection clip is the amplitude about 3Vpp and the frequency defaults to 1 kHz.

Quick Guide UPO1000 Series

10/17

Figure 4-1 Probe Compensation Signal Connection Clip and Ground Terminal

(4) Function Check

Press the AUTO key, a 3 Vpp, 1 kHz square wave should appear on the screen. Repeat step 3 to check all

channels.

(5) Probe Compensation

When the probe is connected to any input channel for the first time, this step might be adjusted to

match the probe and the input channel. Probes that are not compensated may lead to measurement

errors or mistake. Please follow the following steps.

Set the attenuation coefficient in the probe menu to 10x and the switch of the probe at 10x, and

connecting the probe of the oscilloscope to CH1. If use the probe’s hook head, make sure it stably

touch to the probe. Connecting the probe to the “probe compensation signal connection clip” and

connecting the ground alligator clip to the “ground terminal” under the “probe compensation signal

connection clip”. Open CH1 and press the AUTO key.

View the displayed waveform, as shown in Figure 4-2.

Excessive Compensation Correct Compensation Insufficient Compensation

Figure 4-2 Compensating Calibration of Probe

If the displayed waveform is look like the above “Insufficient Compensation” or “Excessive

Compensation”, use a non-metallic screwdriver to adjust the probe’s variable capacitance until the

display matches the "Correct compensation" waveform.

Warning：To avoid electric shock when using the probe to measure high voltage, please ensure that the

probe insulation is in good condition and avoid physical contact with any metallic part of the probe.

Ground terminal

Probe compensation

signal connection clip

Autres manuels pour UPO1000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Unit Équipement de test

Unit

Unit UT528 Manuel utilisateur

Unit

Unit UT659A Manuel utilisateur

Unit

Unit UPO1000X Series Manuel utilisateur

Unit

Unit MSO Series Manuel utilisateur

Unit

Unit UPO2000E Series Manuel utilisateur

Unit

Unit UTD2000CEX+ Series Manuel utilisateur

Unit

Unit UT890D Manuel utilisateur

Unit

Unit MSO2000 Series Manuel utilisateur

Unit

Unit UT313 Manuel utilisateur

Unit

Unit MSO/UPO2000 Series Manuel du propriétaire

Unit

Unit UT525 Manuel utilisateur

Unit

Unit UT3200+ Series Manuel utilisateur

Unit

Unit UT528 Manuel utilisateur

Unit

Unit UT522 Manuel utilisateur

Unit

Unit UT677A Manuel utilisateur

Unit

Unit UTG1000X Series Manuel du propriétaire

Unit

Unit UT512 Manuel utilisateur

Unit

Unit UT3550 Manuel utilisateur

Unit

Unit UT522 Manuel utilisateur

Unit

Unit UT2000 series Manuel utilisateur

Unit

Unit UT712 Manuel utilisateur

Unit

Unit UTD1025CL Manuel utilisateur

Unit

Unit UPO1000CS Series Manuel utilisateur

Unit

Unit UT527 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur