Unit UT528 Manuel utilisateur

P/N:110401105431X

REV.3

DATE:2015/07/15

Overview - UT528/528AU

UT528/528AU from.

UT528/528AU Main Unit

UT528/528AU

2

＊EarthNullingBlock 1x

＊Neck strap 1x

＊IEC Lead 1 x

＊Batteries C Type R14 1.5V UM2 6 x

Safety Information

Warnings - Please be aware of the following warnings.

●Before using the unit and test leads inspect both items. Do not use the unit

and test leads if they are damaged or the case is broken or damaged as this

could result in electrical shock.

●Replace the battery as soon as the battery indicator “ ”appears. Low

battery levels may produce inaccurate readings.

●Do not use or store the unit in high temperature, humid, flammable or

electromagnetic environments as damage and incorrect readings may result.

●If the tester requires repair or replacement please contact your local service

center.

Declaration of Conformity

Uni-T manufactures this product and declares that this product conforms to the

UT528/528AU

4

8.Warning Symbol

9.Unit Error

10.Readings and Cable Results

11.Leakage Current

12.Double Insulated / Class II Test

13.Class I Test

5

ClassITestButton+Zero/NullSelection

Class II Test Button + 250V Insulation Selection

IEC / Cable Test Button +30m Long Lead Selection

Earth Probe Mains / IEC testing

6

Front Panel Operation

1: Press +button to Power on / Power Off.

2: Press button when testing a CLASS I Appliance.

3: Press button when testing a CLASS II Appliance.

4: Press button when performing Cord / Extension Lead testing.

Advance Features

5: Press and hold the button this will set the tester into Long Lead Mode.

6. Press and hold the button to activate 250v insulation test.

You can exit the above advanced features by turning the unit off and back on.

7

Before Testing - Zero the Earth Bond Test Lead!

Plug the earth probe into the rear of the unit and connect it to the earth nulling

adapter. Plug the earth nulling adapter into the front panel earth socket to

complete the circuit.

Press and hold the button for 5 seconds to zero the earth bond reading

using the earth bond lead and the nulling adapter together in the front test socket.

This will null the earth reading of the test lead and “GOOD” will be displayed once

complete. It is good practice to do this once prior to carrying out testing.

Auto Switch Off

The unit will automatically switch off after approximately 2 minutes if no buttons

are pressed.

Testing a Class 1 Appliance

Plug the appliance into the UT528/528AU panel main socket. Plug the earth test lead into

the socket on the UT528/528AU end panel. Connect the earth crocodile clip to an

8

exposed metal part on the appliance as shown in Diagram 3.

1. Earth / Protective Conductor Test

Press the Class 1 test button to start the test. The earth resistance test will

begin.

9

If the earth resistance measured is greater than 0.2Ω, the meter will display “×

Rpe”, which is a FAIL. If this occurs, re- check the connections between the pin of

the plug to the bodywork of the appliance and that the crocodile clip is attached to

clean earthed metalwork on the appliance (try attaching the clip to an alternative

piece of metalwork). If all connections are ok the appliance earth connection may

be faulty.

The PASS mark for the earth bond test is 0.2 Ωfor a Class 1 appliance.

If the reading is less than 0.2 Ω, the meter will display “√Rpe”, which is a PASS.

The unit will then automatically attempt to proceed to the insulation test. If it

detects that the appliance’s power switch is in the ON position it will carry out the

insulation test automatically.

If this is not detected the unit will display a flashing symbol and also “LO

LOAD”. Press the button to proceed to the insulation test.

Autres manuels pour UT528

1

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Unit Équipement de test

Unit

Unit UPO2000E Series Manuel utilisateur

Unit

Unit UT522 Manuel utilisateur

Unit

Unit UPO1000CS Series Manuel utilisateur

Unit

Unit UT525 Manuel utilisateur

Unit

Unit UT2000 series Manuel utilisateur

Unit

Unit UPO3000E Series Manuel utilisateur

Unit

Unit UPO1000 Series Manuel utilisateur

Unit

Unit UTD1000L Series Manuel utilisateur

Unit

Unit UT659A Manuel utilisateur

Unit

Unit UPO3000E Series Manuel du propriétaire

Unit

Unit UT501B Manuel utilisateur

Unit

Unit UT521 Manuel utilisateur

Unit

Unit UT3550 Manuel utilisateur

Unit

Unit UT15A Manuel utilisateur

Unit

Unit UT3500 Series Manuel utilisateur

Unit

Unit UT522 Manuel utilisateur

Unit

Unit UT261 Series Manuel utilisateur

Unit

Unit UTD1025CL Manuel utilisateur

Unit

Unit MSO2000 Series Manuel utilisateur

Unit

Unit UT5300X+ Series Manuel utilisateur

Unit

Unit UTL8200 Series Manuel utilisateur

Unit

Unit utd2000 Manuel utilisateur

Unit

Unit UPO1000 Series Manuel utilisateur

Unit

Unit UTD2000M Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur