Unit UTD4000 Series Manuel utilisateur

Safety Instructions

This unit is designed and manufactured strictly in

accordance with GB4793 safety requirements for

electronic testing meters and IEC61010-1 safety

standards. It fully meets CAT II 600V insulation and

overvoltage requirements and Grade II anti-pollution

safety standards. To prevent personal injuries and

damage of this unit or any other devices connected to

it please take note of the following safety precautions

To avoid potential hazards use this unit strictly as

instructed by this User Manual

Use only the specified

power cable which is authorized in the country of use.

Do not remove the

probe

or testing cable when they are connected to power.

This unit is grounded by

the ground wire of the power cable. To avoid electric

shock, the grounding conductor must touch the

ground. Before connecting the input or output

terminal, ensure the unit is properly grounded.

The probe ground cable is the same

as ground potential. Do not connect the ground cable

to non ground voltage or high voltage.

To prevent

fire and excessive current shock please check all

ratedvaluesandlabeldata Read the manual

carefully and check the rated values before

connecting the unit

Do not operate this unit when t

he outer cover

or front panel is open.

Only use specified fuse types

and rated specifications.

When power is on, never

make contact with exposed adaptor or components.

, .

Maintenance should only be carried out by a

trained professional.

To avoid fire and personal injury

Use a correct power cable

Remove the plug correctly

Ensure good grounding :

Connect the probe of the digital storage

oscilloscope

Check the rated values of all terminals

Do not operate the unit with the chassis cover

open

Use suitable fuses

Avoid exposing circuitry

UTD4000 Four-channel

User Manual

When fault is suspected, stop operation

Maintain good ventilation.

Do not operate in humid condition.

Do not operate in combustible and explosive

conditions.

Keep the product surface clean and dry.

Messages on the product

Danger

Warning

Caution

Icons on the product

If you

suspect a fault, ask a qualified maintenance

professional to carry out inspection.

Safety terminology used in this manual. The following

messages may appear in this manual

The following

messages may appear on the product

means potential damage that is

immediate

means potential damage that is not

immediate

means possible damage to this product

or other properties

The following icons may

appear on the product

Safety Messages and Symbols

" "

Warning

Warning statements identify conditions

or practices that could result in injury or loss of life

Caution

Caution statements identify conditions

or practices that could result in damage to this unit

or other properties

UTD4000 Four-channel

User Manual

Protective

ground terminal

Ground terminal

for chassis

Ground terminal

for testing

Caution!

Refer to manual

High voltage

Preface

This manual provides information on the operation of the

UTD4000 four-channel digital storage oscilloscope series.

Guidance is given in several chapters as follows :

Simple guide to oscilloscope

functions and installation

Guide to operation of

the UTD4000 four channel digital storage oscilloscope

series.

Example

illustrations are provided to solve various testing

problems

Chapter 1 User Guide

Chapter 2 Instrument Setups

Chapter 3 Practical Illustrations

Chapter 4 System Prompts and Trouble shooting

Chapter 5 Servicing and Support

Chapter 6 Appendixes

Appendix A : Technical Indicators

Appendix B : Accessories for UTD4000 Four-channel

Digital Storage Oscilloscopes

Appendix C : Maintenance and Cleaning

Appendix D : Factory Setup

UTD4000 Four-channel

User Manual

The UTD4000 Four-channel Digital Storage Oscilloscope Series

UTD4000 four-channel digital storage oscilloscopes offer user-friendliness, outstanding technical indicators

and a host of advanced features. They are your perfect tools to complete testing tasks swiftly and efficiently.

This manual is a user guide for 3 models of this digital storage oscilloscope series :

UTD4000 Four-channel

User Manual

Model

Bandwidth

Single-channel Sampling

Rate

Dual-channel Sampling

Rate

Equivalent Sampling

Rate

UTD4104C

UTD4204C

100MHz

200MHz

2GS/s

UTD4304C

300MHz

2GS/s

1GS/s

50GS/s

UTD4000 four-channel digital storage oscilloscopes

offer a user-friendly front panel with clear indications

to allow access to all basic functions for easy

operation. The scaling and position buttons for all

channels are optimally arranged for intuitive

operation As design is based on the familiar

practices of traditional instruments users can use

the new units without spending considerable time

in learning and familiarizing with operation For

faster adjustment to ease testing, there is an [ ]

key to instantly display the appropriate waveform and

range position.

The performance fe

atures listed below will explain

why the UTD4000 series can fully

satisfy your testing and measurement requirements

2GS/s real-time sampling rate and 50GS/s

equivalent sampling rate

Dual time base function unrivaled waveform

detail observation and analysis capabilities

24k storage depth; 60M equivalent storage

depth; 1024k recording length

Unique envelop sampling feature with direct

visual display of carrier wave details after

amplitude modulation

Scroll display in scan mode for continuous

monitoring of signal variations

Unique XY mode that displays the waveform and

Lissajou

s figure concurrently

USB drive system software upgrade

Supports plug-and-play USB storage device.

Communication with computer through the USB

device

Storage of waveforms setups and bit maps

waveforms and setups reproduction

Built-in FFT

Multiple waveform mathematics functions

(including add, subtract, multiply and divide)

;

, ;

AUTO

Four-channel

●

UTD4000 Four-channel

User Manual

UTD4000 Four-channel

User Manual

●

Edge, video, pulse, slope and alternate trigger

functions

Automatic measurement of 24 waveform parameters

parameters testing and customization

Multiple setups for extra flexibility

Visual system help messages

4 x 1.2m, 1:1/10:1 probe. For details refer to the

probe instructions. These accessories conform

with EN61010-031: 2008 standards

Power line conforming to international standards

applicable in the country of use

User Manual

USB connecting cable : UT-D06

UTD4000 four-channel oscilloscope

communication control software (USB-device)

2x multimeter test lead; 2x c -to-vol

tage

converter module: UT M03/UT-M04

;

AUTO

UTD4000 Four-channel accessories :

urrent

TableofContents

Item Page

SafetyInstructions

Preface

Chapter1

FunctionalCheck

ProbeCompensation

AutomaticSetupforWaveformDisplay

GettingtoKnowtheVerticalSystem

GettingtoKnowtheHorizontalSystem

GettingtoKnowtheTriggerSystem

Chapter2 InstrumentSetups

SettingtheVerticalSystem

SettingtheHorizontalSystem

SettingtheTriggerSystem

Setting the Display System

UserGuide------------------------------------------------------------------------------

GeneralInspection----------------------------------------------------------------------

-----------------------------------------------------------------------

------------------------------------------------------------------

----------------------------------------------

--------------------------------------------------

-----------------------------------------------

----------------------------------------------

----

---------------------------------------------------------------------

------------------------------------------------------------

---------------------------------------------------------

------------------------------------------------------------

----------------------------------------------------

------------------------------------------------------------------

--------------------------------------------------------

Setting the Sampling System

Storage and Recall

UTD4000 Four-channel

User Manual

Item Page

Automatic Measurement

UsingtheRun/Stop

Auto Setup

Help System

Chapter3 PracticalExampleIllustrations

Illustration 1 : Measuring simple signals

Illustration 2 : Observing the delay caused by a

sine wave signal passes through the circuit

Illustration 3 : Acquiring single signals

Illustration 4 : Reducing random noise of signals

Illustration 5 : Using the cursors for measurement

Illustration 6 : Using the X-Y function

Illustration 7 :

Illustration 8 :

----------------------------------------------------------------

-----------------------------------------------------------

-----------------------------------------------------------------

-----------------------------------------------------------------------

-------------------------------------------------------------------------------

-------------------------------------------------------------

-----------------------------------------------------------------------------

------------------------

-----------------------------------

-------------------------------------------

---------------------------------------

---------------------------------------------

---------------------------------

-------------------------------

-----------------------------------------------

------------------------------

-------------------------------------------------

Utility Function Setup

Cursor Measurement

Multimeter Measurement

Vedio signal triggering

Using the dual time base function

Illustration 9 : Using the multimeter

UTD4000 Four-channel

User Manual

tem Page

Chapter 4 System Prompts and Trouble-shooting -------------------------------------------

Definitions of System Prompts -----------------------------------------------------

Troubleshooting-----------------------------------------------------------------------

Chapter 5 ----------------------------------------------

Chapter 6 Technical Indicators ------------------------------------------------------------------

Appendix A : Technical indicators--------------------------------------------------

Appendix B :

----------------

--------------------------------------------------

Appendix C : Maintenance and Cleaning-----------------------------------------

Appendix D -------------------------------------------------------

Upgrading System Software on USB

Accessories for UTD4000 Four-channel Digital Storage

Oscilloscope Series

Factory Setups

106

115

116

117

UTD4000 Four-channel

User Manual

Chapter 1 UserGuide

Your UTD4000 Four-channel digital storage

oscilloscope is a small and compact benchtop device.

The user-friendly front panel enables easy operation.

This chapter will guide you through basic testing

steps.

This chapter provides notes on the following :

General inspection

Functional check

Probe compensation

Automatic setups for waveform display

Getting to know the vertical system

Getting to know the horizontal system

Getting to know the trigger system

When beginning to use your UTD4000 Four-channel

oscilloscope, first familiarize yourself with the

operation front panel. This ch

apter briefly describes

the operation and functions of the front panel, so you

can get started with your UTD4000 four-channel

digital storage oscilloscope as quickly as possible.

Your UTD4000 Four-channel oscilloscope comes with

a front panel with at-a-glance functions for easy

operation There are knobs and function keys on

the front panel The functions of knobs are similar

to other oscilloscopes On the right you will find 5

menu operation keys designated as to

from top down With these keys you can set up

different options of the current menu. The other keys

are function keys. You can use the

m to enter different

function menus or access particular functions directly.

●

( [ ] [ ]

F1 F5

UTD4000 Four-channel

User Manual

Autres manuels pour UTD4000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Unit Équipement de test

Unit

Unit UT311A Manuel utilisateur

Unit

Unit UT528 Manuel utilisateur

Unit

Unit UPO2102 Manuel utilisateur

Unit

Unit UT525 Manuel utilisateur

Unit

Unit UT713 Manuel utilisateur

Unit

Unit UT5300X+ Series Manuel utilisateur

Unit

Unit UT-P35 Manuel utilisateur

Unit

Unit UTD2025 series Manuel utilisateur

Unit

Unit UT 4000 Series Manuel utilisateur

Unit

Unit UT279 Manuel utilisateur

Unit

Unit UT712 Manuel utilisateur

Unit

Unit UT3200+ Series Manuel utilisateur

Unit

Unit MSO/UPO2000 Series Manuel du propriétaire

Unit

Unit UT361 Manuel utilisateur

Unit

Unit UT12A Manuel utilisateur

Unit

Unit UTD1000L Series Manuel utilisateur

Unit

Unit UPO1000CS Series Manuel utilisateur

Unit

Unit UT590 Series Manuel utilisateur

Unit

Unit UT522 Manuel utilisateur

Unit

Unit UT581 Manuel utilisateur

Unit

Unit UTD2000CEX-II Series Manuel utilisateur

Unit

Unit UT-513A Manuel utilisateur

Unit

Unit UT526 Manuel utilisateur

Unit

Unit utd2000 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur