TYAN THUNDER LE-T Manuel utilisateur

http://www.tyan.com

Thunder LE-T

S2518

User’s Manual

Revision 1.20

may be reproduced or translated without prior written consent from Tyan Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

Tyan, Thunder LE-T S2518 are trademarks of Tyan Computer Corporation.

Intel, Intel Pentium, combinations thereof are trademarks of Intel Corporation.

ServerWorks, ServerSet III LE3, combinations thereof are trademarks of Broadcom/ServerWorks,

Corp.

AMI, AMI BIOS are trademarks of American Megatrends Inc.

Microsoft, Windows are trademarks of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Micronics is a trademark of Micronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Iomega, Zip are registered trademarks of Iomega Corporation.

Information contained in this document is furnished by Tyan Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. Tyan assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of Tyan products including

liability or warranties relating to fitness for a particular purpose or merchantability. Tyan retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will Tyan be held liable for any direct or indirect, incidental or consequential damage, loss

of use, loss of data or other malady resulting from errors or inaccuracies of information contained in

this document.

http://www.tyan.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.1 Congratulations!

1.2 Hardware Specifications

1.3 Software Specifications

Chapter 2: Board Installation

2.1 Front Panel Connector

2.2 CMOS Reset

2.3 PCI Speed Jumper

2.4 FSB Speed Jumper

2.5 LAN1/2 Activity LED Headers

2.6 FAN Connectors (FAN 1 to 6)

2.7 Speaker Connector

2.8 CPU Voltage ID Mismatch LED

2.9 IDE RAID Connector

2.10 SCSI Connectors

2.11 Parallel Port Connector

2.12 USB Port Headers

2.13 Serial Port Header

2.14 Slim Floppy Connector (optional)

2.15 Riser Card Information

2.16 Hardware Reset Switch Connector

2.17 BIOS Flash Utility

2.18 Mounting the Motherboard

2.19 Installing Memory

2.20 Installing CPU and Cooling Fans

2.21 Connecting IDE and Floppy Drives

2.22 Installing Add-in Cards

2.23 Connecting PS/2, USB, Serial

2.24 Connecting the power supply

2.25 You’re done!

Chapter 3: BIOS Setup

3.1 Main Setup

3.2 Advanced

3.2a Super I/O Configuration

3.2b IDE Configuration

3.2c Floppy Configuration

3.2d Boot Settings Configuration

3.2e Onboard Device Configuration

3.2f Even Log Configuration

3.2g Remote Access Configuration

3.3 Chipset

3.4 PCIPnP

3.5 Boot

3.6 Power

3.7 Security

3.8 Exit

……………………………………………..Page 4

……………………………………………..Page 5

……………………………………………..Page 6

……………………………………………..Page 7

……………………………………………..Page 8

……………………………………………..Page 9

……………………………………………Page 10

……………………………………………Page 11

……………………………………………Page 12

……………………………………………Page 13

……………………………………………Page 14

……………………………………………Page 15

……………………………………………Page 16

……………………………………………Page 17

……………………………………………Page 18

……………………………………………Page 19

……………………………………………Page 20

……………………………………………Page 21

……………………………………………Page 22

……………………………………………Page 23

……………………………………………Page 24

……………………………………………Page 25

……………………………………………Page 26

……………………………………………Page 28

……………………………………………Page 30

……………………………………………Page 31

……………………………………………Page 32

……………………………………………Page 33

……………………………………………Page 34

……………………………………………Page 35

……………………………………………Page 36

……………………………………………Page 37

……………………………………………Page 38

……………………………………………Page 39

……………………………………………Page 40

http://www.tyan.com

Chapter 4: Installing the Hard Drives

SCSI Setup Section

Chapter 5: System Resources

5.1 Beep Codes

5.2 Flash Utility

Appendix I: Hardware Monitoring Information

Appendix II: Glossary

Technical Support

……………………………………………Page 41

……………………………………………Page 45

……………………………………………Page 55

……………………………………………Page 56

……………………………………………Page 57

……………………………………………Page 62

http://www.tyan.com

Before you begin…

Check the box contents!

The retail motherboard package should contain thefollowing:

1x Thunder LE-T motherboard

1x 34-Pin floppy drive cable

2x Ultra-DMA-100/66/33 IDE cable (1 for optional IDE if included onboard)

1x Ultra160 SCSI cable (for optional SCSI if included onboard)

1x 64-bit PCI Riser card

1x Cable set: 9-pin Serial and 25-pin printer cables

1x Thunder LE-T user’s manual

1x Tyan driver CD

1x Adaptec 7899W NT Ultra160 SCSI driver diskette (if optional SCSI included)

1x Promise 20267 NT/2000/XP driver diskette (if optional IDE included)

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

http://www.tyan.com

Chapter 1: Introduction

1.1 Congratulations!

You are now the owner of the Tyan Thunder LE-T motherboard, the most reliable, high

performance motherboard for dual Pentium III processing. Designed to be portable as well as

flexible, the Thunder LE-T can fit into standard ATX chassis and 1U and 2U rackmount chassis.

This platform utilizes ServerWorks’ high-performance ServerSet III LE3 chipset, enabling next

generation application and platform support. Intel Pentium III processors between 500MHz and

1.7GHz* are supported in single and dual configuration. *Please see Tyan’s website for updates

and information concerning CPU information and support:

http://www.tyan.com

This integrated performance board is supported in an ATX form factor. Features of the Thunder

LE-T include onboard UltraDMA-33 (UltraDMA-100/66 with Promise controller and Ultra160SCSI

with onboard Adaptec controller) and multiple boot options.

With both I/O and drive controller support onboard, dual 64-bit PCI slots provide upgrade solutions

for future add-in cards. Integrated 2D/3D graphics provided by the onboard ATI RAGE XL

controller enables ease of use into 1U and 2U chassis. Dual onboard LAN ports provide

connectivitywithoutadd-in overhead.

The Thunder LE-T supports up to 4GB of Registered ECC PC133 SDRAM.

Remember to visit Tyan’s Website at http://www.tyan.com. There you can find information on all of

Tyan’s products with FAQs, distributors list and BIOS setting explainations.

1.2 Hardware Specifications

Processor

•Dual PGA370 ZIF sockets

•Supports up to two Intel PentiumIII

processors

•Supports Intel’s PentiumIII Processor DP

•One onboard VRM (VRM 8.5) supports 2

CPUs

•Front-side bus support for 100/133MHz

Chipset

•ServerWorksLE chipset

•Integrated I/O APIC

•OSB4 south bridge

•SMSC FDC37B787 Super I/O ASIC

Memory

•Four 3.3v 168-pin DIMM sockets

•25-degrees angledsockets enable

rackmount installation

•Supports up to 4GB of Registered

PC133/100 SDRAM

•Supports ECC (72-bit) memory

IntegratedLAN

•Dual Intel82559 LAN controllers

•10/100Mbps max data rate per controller

Integrated 2D/3D Graphics

•ATIRAGE XL graphics controller

•4MB frame buffer (SDRAM)

•Standard 15-pin analog VGA port

IntegratedATA-100/IDE RAID

(manufacturingoption)

•PromiseFastTrak 100 RAID controller or

PromiseATA-100 controller

•Dual-channel busmaster mode

•Supports up to four E-IDE drives

•Supports UltraDMA-100/66/33 drives

•SupportsATA-100 IDE RAID levels 0, 1

and 0+1

http://www.tyan.com

Expansion Slots

•Two 64-bit/66MHz (one 5v, one 3.3v) PCI

slots

•Total of two usable slots (one if installed in

1U chassis)

•PCI riser card required when installed in

1U/2U chassis

Integrated PCI IDE

•Dual-channel master mode

•Up to four E-IDE drives

•Support for DMA/ATAPI devices

Integrated I/O

•One floppy connector supports up to two

drives (second one via optional slim FD

connector)

•Two 9-pin 16550-based serial ports (one via

optional cable)

•One 25-pin SPP/ECP/EPP parallel port (via

optional cable)

•Four USB ports (two via optional cable)

•PS/2 keyboard and mouse ports

Integrated SCSI (manufacturing option)

•AdaptecAIC-7899W controller

•Dual-channel Ultra160 SCSI support

•160MB/sec max data throughput per

channel

•Supports up to 15 LVD SCSI devices per

channel

HardwareMonitoring

•Dual Winbondchips

•WinbondW83782D hardware monitoring

ASIC

•CPU Temp, voltage and fan monitoring

BIOS

•AMI4Mb BIOS Flash ROM

•Auto-configure IDE drive types

•Multiple boot options

•DMI 2.0 compliant

Form Factor

•ATX footprint (12” x 9.6”, 304.8mm x

243.84mm

•One 20-pin ATX power connector

•One Serial port and one VGA port

•Stacked USB (two) ports

•Side-by-side LAN (two) ports

•Stacked keyboard and mouse ports

Regulatory

•FCC DoC (declaration of Conformity)

•European Community of CE (declaration of

Conformity)

1.3 Software Specifications

OS Windows NT/2000/XP, Red Hat Linux 7.x*

*Support of Red Hat 7.x is limited by Red Hat’s customer support for this product andversion

Tyan takes no responsibility and will not be held liable if Red Hat should no longer support Red

Hat 7.x.

http://www.tyan.com

Chapter 2: Board Installation

Installation

You are now ready to install your motherboard. The mounting hole pattern of the Thunder LE-T

matches the ATX system board specifications. Your chassis should support a standard ATX

motherboard form factor.

How to install our products right… the first time

The first thing you should do is read this user’s manual. It contains important information which will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer powersupply and then touch the power supply.

For the safest conditions, Tyan recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board.

(3) Avoid touching the motherboard components, IC chips, connectors, and leads.

(4) Avoid touching memory module contacts and IC chips

(5) Place the motherboard on a grounded antistatic surface or on the antistatic bag from

which it came in.

Having reviewed the precautions above, the next step is to take the motherboard out of the

cardboard box and static bag, hold it by its edges and place it on a grounded antistatic surface,

component side up. Inspect the board for damage.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.tyan.com

2.1 Front Panel Connector (J80)

Your chassis will usually come with connectors to install onto the motherboard, such as HDD and

Power LEDs. The Front Panel Connector (J80) has been implemented for such purposes.

J80

Infrared

(IrDA)

HM_INTR

IR TX

RST

HDD

LED

GND

IR RX

VCC

GND

VCC+

16 1418 12 10 8642

GND

Slp LED+

Pwr LED+

PWR

LED

http://www.tyan.com

2.2 CMOS Reset(JP1)

If you have been locked out of your system because you forgot your password, or set the CMOS

incorrectly, or have just finished flashing your BIOS, you will need to reset the CMOS. The

instructions are as follows:

1. Power off the system

2. Close J58

3. Wait about three seconds

4. Open J58, then power on the system again

By following this procedure, you will erase your password and reset the CMOS. The location of

J58 is shown in the diagram below.

J58

OPEN

Normal

* default is OPEN

OPEN

Normal

http://www.tyan.com

2.3 PCI Speed Jumper (J60)*

With this jumper, the PCI bus can be set to either 33 or 66MHz. Please check the PCI card speed

before setting J60. Setting the PCI bus to 66MHz, while the PCI devices can only run at 33 MHz,

will cause those PCI devices to run past their designated busspeeds.

Pay careful attention to the speed of the devices that you will be installing

into the PCI slots, and use that information to set J60 accordingly. Setting

the PCI bus to a speed higher than your PCI device can handle will

damage the PCI device.

Tyan takes no responsibility and will not be held liable for damage related

to the operation of the PCI device using different settings from those of the

PCI device manufacturer’s specified device settings.

NOTE

J60

OPEN

66MHz

33MHz

* default is OPEN

* Onboard Adaptec 7899W, if available on your Thunder LE

T, runs on a 66MHz SCSI bus.

After setting the SCSI bus to 33MHz, the Adaptec 788W will be downgraded to 64-bit / 33MHz

speed.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TYAN Carte mère

TYAN

TYAN TIGER I7501R Manuel utilisateur

TYAN

TYAN Thunder n4250QE-S4985G3NR-E Manuel utilisateur

TYAN

TYAN THUNDER I840 Manuel utilisateur

TYAN

TYAN THUNDER LE Manuel utilisateur

TYAN

TYAN S7066 Manuel utilisateur

TYAN

TYAN S7056 Manuel utilisateur

TYAN

TYAN S8030 Manuel utilisateur

TYAN

TYAN TOMCAT IIIS D Manuel utilisateur

TYAN

TYAN TRINITY I845E Manuel utilisateur

TYAN

TYAN S8028 Manuel utilisateur

TYAN

TYAN S7063 Manuel utilisateur

TYAN

TYAN Tempest i5000VS S5372-LC Manuel utilisateur

TYAN

TYAN TITAN III Manuel utilisateur

TYAN

TYAN TOMCAT I875PF Manuel utilisateur

TYAN

TYAN Thunder i7500 Pro S2721 Manuel utilisateur

TYAN

TYAN Thunder i7501 S2720-533 Manuel utilisateur

TYAN

TYAN THUNDER K8S Manuel utilisateur

TYAN

TYAN Tiger MPX S2466 Manuel utilisateur

TYAN

TYAN S5548GM4NED83-4T Manuel utilisateur

TYAN

TYAN Thunder n3600QX Manuel utilisateur

TYAN

TYAN S7065 Manuel utilisateur

TYAN

TYAN S5510 Manuel utilisateur

TYAN

TYAN THUNDER H2000M Manuel utilisateur

TYAN

TYAN TIGER I7501X Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur