Turnigy Fabrikator II mini Manuel utilisateur
Instruction Manual
1
A.
B.
C.
D.
E.
F.
G.
H.
I
J.
K.
Precautions..……………………………......…....
Checklist..……………………………...…...........
Component Diagram..…………………………..
Specifications..……………………………...…...
Hardware Installation..………………………….
Setting Up ..……………………………...…........
Commissioning..……………………………...…
Wireless Network Function.............................
Printing..……………………………...….............
Troubleshooting...............................................
Maintenance.....................................................
NOTE.................................................................
P. 2
P. 3
P. 3
P. 4
P. 5
P.5-9
P.10-14
P.14-16
P.17-19
P.20
P.21
P.22
TABLE OF CONTENTS
A. PRECAUTIONS
2
1. Do not remove the print surface from the platform, it is a special tape that allows the
first layer of your print to adhere to the print bed.
2. Do not remove the tape or insulation from the nozzle, it is for maintaining nozzle
temperature.
3. Use this printer using the correct voltage input and follow all local laws.
4. Beware the heat blocks, nozzles, extruded filament and heating plate can be
extremely hot and will burn your skin if you are not careful.
5. Do not wear gloves when operating or repairing to avoid entanglement.
6. Do not leave the machine unattended when it is in operation.
7. At the end of its life please dispose of your 3D printer responsibly.
8. Do not load unsupported filament.
9. Keep your 3D printer and all accessories out of children’s reach.
10. When printing via USB, keep a stable connection between the PC and the printer.
11. Do not move the extruder during printing.
12. Do not pull or twist the power cable during operation.
13. Do not force or tear anything during unpacking and setup. This may damage the printer.
14. WARNING
a) Never reach inside while it is in operation. Always allow it to cool down before
reaching inside.
b) If opening the printer for service, ensure that the power supply is turned off and
the cord is disconnected.
15. CAUTION
a) Please take your time and be careful while unpacking and setting up your
3D printer; there are many components that can be damaged if it is not set up or
handled correctly.
3
B. CHECKLIST
C. COMPONENT DIAGRAM
3D Printer
Micro USB cable
Micro Memory card
Power adapter
Power line
Plastic scraper
1
1
1
1
1
1
5Power switch
4Extruder motor
3Bowden tube
2USB and Memory card slots
1Extruder
5
2
1
4
3
4
D. SPECIFICATIONS
Product
Usage
Construction
Extruder
Nozzle diameter
Positioning Precision
Layer Resolution
Input Power
Nozzle heating
Filaments
Interface
Build Surface
Supported File
OS
Certificate
Warranty
Product Dimension
Build Volume
Shipping Box
FDM Desktop 3D Printer
Rapid Prototyping, print 3D models, samples, parts, toys...
Aluminum
Single
0.4 mm (0.015 in)
XY 11 microns (0.0004 in), Z 2.5 micron (0.0001 in)
100 micron (0.0039 in)
100-240V, Max:80W
Max 250℃
1.75mm diameter PLA
Memory card, USB and wireless network
Heating bed with PEI coating
STL, OBJ/G-Code
Windows10, Mac OS X, Linux
CE, ROHS, FCC,ISO 9001:2008
6 months
About 17.2x18.3x27 cm
100x100x100 mm
About 220x220x320 mm
5
E. HARDWARE INSTALLATION
1. Connect the power line and the Micro USB line.
F. SETTING UP
Software installation on PC
1. Installation
To get started you will need a PC or laptop with an SD card reader, that is turned on
and in proximity to your Mini Fabrikator V2 3D printer. You will also need access to
mains power to connect to the printer’s power supply. Included in the provided SD
memory card you will find the Repetier installation package, this is a slicer tool that
you use to convert your 3D files to the commands the printer needs to make your
objects, it is also one of the interfaces you can use to set up your printing parameters
such as temperatures and movements, please open this file and follow the steps
below to install this software.
6
2. Set print parameters
After running the software you can begin to adjust the parameters of the software to
suit to the Mini Fabrikator V2 by clicking on the printer settings icon the top right
corner of the window.
In the settings window, click on the “Connection” tab, please refer to the following
settings to set the parameters.
After the installation is complete, click Finish to run the software.
7 7
Then click on the “Printer” tab and input the settings below:
Then click on the “Extruder” tab and input the settings below:
Finally click on the “Printer Shape” tab and input the settings below:
8
3. Set CuraEngine
Now that the printer is set-up it is time to set up the slicer program that works with
Repetier, there a few slicer engines to choose from we recommend Cura. To make
things easier we made a pre-configured Mini Fabrikator V2 file that can just be
imported. If you don’t have access to this file you can quickly configure the Cura
Slicer in the following steps. Let’s head back to Repetier-Host program. Look along
the top right and find the “Slicer” tab. Select the “CuraEngine” from the drop down.
The screen should look like the diagram below. Click on the “Configuration” button so
we can import the file we just downloaded. Following the data shown in the images
below, fill in the data for each of the first 4 tabs then click Save. Double check these
settings match those below and don’t forget to click save.
9
Table des matières
Autres manuels Turnigy Imprimante 3D
