TRNDlabs SKEYE Manuel utilisateur
SKEYE
USER GUIDE
Mini Drone
2
Parts Idencaon
SKEYE Mini Drone
USB Charging Cable
MicroSD Card
Rotor Protecon Cage
Replacement Rotor Blades
MicroSD card reader
Controller
Rechargeable Baery
3
Baery Installaon
Sensivity Flip
Direcon
Forward/Backward
Sideways
Forward Trimmer
Sideways Trimmer
Right
Not In Use
Video
Rotaon
Power Switch
ON/OFF
Sideways
Trimmer Le
Backward
Trimmer
Throle/Rotate
Photo
Rotaon
Trimmer /Le
Not In Use
Controller Funcons
Geng Started
1. Use a screwdriver to open the controller baery cover.
2. Install 4x 1.5V AA baeries into the controller.
3. Lock the baery cover.
Parts Idencaon
4
Charging
1. Disconnect the power cable.
2. Connect the USB charging cable to a USB port. The LED on the USB
charging cable lights red indicang that the baery is charging. When the
baery is fully charged, the LED on the USB charging cable turns o. It takes
about 60 minutes to recharge a discharged baery.
2. Slide the baery into the baery
bay on the boom of the drone.
Connect the power cable.
1. Move the throle/rotate sck
to the full down posion.
Make sure you only charge the rechargeable baery with the supplied USB
charging cable. If you try to charge the rechargeable baery with a dierent
baery charger, this might cause serious damage.
Immediately aer switching it on, place the drone on a at and level surface.
The gyro-system will then set itself automacally.
Flying Your Drone
5
4. The controller needs to be
calibrated aer successful binding:
move the throle/rotate sck to
the full up posion and then push
the throle/rotate sck to the full
down posion. When the LED on
the controller and the LEDs on the
drone are all solid (not blinking), the
drone is ready to y.
3. Push the power switch of the
controller to the ON posion. The
controller will emit a tone to
indicate that binding is complete. At
the same me, the LED lights on the
drone will start to ash slowly.
Throle Control
Pushing the Throle/Rotate sck forward will cause the main rotors to spin.
The farther you push the sck, the faster the rotors will spin, causing the
drone to li o and gain altude.
If you noce that the drone moves forward or to the side without you
touching the control scks, please adjust the trim of the drone as described in
“Trimming”.
To start or to y higher, push the throle/rotate sck cauously forwards. To
land or y lower, push the throle/rotate sck cauously backwards.
Flight Controls
6
Rotaon Control
To y the drone to the le or the right, push the direcon sck cauously to
the le or the right.
To make the drone circle to the le or the right, move the throle/rotate sck
cauously to the le or the right.
Direcon Control
To y the drone forwards or backwards, push the direcon sck cauously to
forwards or backwards.
7
The drone has two sensivity sengs: beginner and advanced.
Press the sensivity buon in order to change the sensivity:
1. When the controller emits 1 tone = beginner sensivity mode.
2. When the controller emits 2 tones = advanced sensivity mode.
A higher sensivity makes the drone faster
and more responsive.
Sensivity Control
The drone can perform 360° front ips, back ips and side ips. Press the ip
buon, then push the Direcon sck forward, backward, right or le at the
same me. The drone carries out the ip in the respecve direcon.
Advanced Flight: Performing 360° Flips
Do not aempt these stunts unl you are able to y condently. Choose an
area that will provide a so landing (carpet or grass) and maintain an altu
de of at least 10 feet/3 meter to allow room to recover control as you
pracce ipping the drone.
8
Forward 360° Flip
Press the ip buon and push the direcon sck to the right at the same me.
Le Side 360° Flip
Right Side 360° Flip
Press the ip buon and push the direcon sck to the le at the same me.
Press the ip buon and push the direcon sck to the right at the same me.
9
Backward 360° Flip
Direcon Trim
Press the ip buon and push the direcon sck backward at the same me.
The correct trim is a basic requirement for fault-free ying behavior
of your drone.
When hovering, if the drone ies forwards or backwards without you moving
the direcon sck, please proceed as follows:
If the drone moves on its own forwards, press the backward trimmer in steps.
If the drone moves on its own backwards, press the forward trimmer in steps.
Trimming
10
Rotaon Trim
When hovering, if the drone ies to the le or right without you moving the
direcon sck, please proceed as follows:
If the drone moves on its own sideways to the le, press the
right trimmer in steps.
If the drone moves on its own sideways to the right, press the
le trimmer in steps.
When hovering, if the drone rotates to le or right without you moving the
rotaon sck, please proceed as follows:
If the drone moves on its own le, press the right trimmer in steps.
If the drone moves on its own right, press the le trimmer in steps.
Table des matières
Autres manuels TRNDlabs Drone
