TRENDnet TEW-715APO Manuel utilisateur
N150 Wireless Outdoor PoE Access Point
TEW-715APO
Quick Installation Guide (1)
TEW-715APO (V1.0R) / 08.23.2012
Minimum Requirements
TEW-715APO
CD-ROM (User's Guide)
Multi-Language Quick Installation Guide
PoE injector
Power cord
Pole mounting clamp
Grounding wire
Computer with an Ethernet port and Web
Browser
A network switch or router with an available
network LAN port
2 x RJ-45 network cables
Note: The TEW-715APO does not support IEEE 802.3af. You must use the proprietary Power over
Ethernet injector that is supplied with the TEW-715APO.
Note:
1. The default IP address of the TEW-715APO is 192.168.10.100. To configure the TEW-715APO,
your network adapter must have an IP address within the 192.168.10.x subnet (e.g.
192.168.10.50). Please refer to the Appendix in the User's Guide for more information.
2. Disable any anti-virus and firewall programs before configuring the access point.
Package Contents
1. Before You Start
1
2. Hardware Configuration
Note:
1. The initial configuration should be completed in a testing environment with the two
TEW-715APO's approximately 15 ft. (5 meters) apart from one another.
2. Configure and connect the devices before mounting.
Phase 1: Configuration
2
TEW-715APO
3
2. Pinch the tab and slide the cover down.
11. Click Wireless and then click Basic
Settings.
12. Select Bridge for Operation Mode.
13. Click Apply.
1. Write the MAC address of the two
TEW-715APOs. The MAC address can be
found on the back of the unit.
3. Connect one end of a network cable into the
TEW-715APO #1.
Remove the bottom cover and connect a
network cable to the PoE port.
4. Connect the opposite end of the network
cable to the POE port on the Power over
Ethernet Injector.
5. Connect one end of another network cable to
the LAN port on the Power over Ethernet
Injector.
6. Connect the other end of a network cable to
your computer's Ethernet port.
7. Connect the power adapter into the Power
over Ethernet Injector. Then connect the
power adapter into a power outlet.
8. Assign a Static IP address to your computer's
network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.25) and a
subnet mask of 255.255.255.0.
9. Open your web browser, type the IP address
of the access point in the address bar, and
then press Enter. The default IP address is
192.168.10.100
10. Enter the User name and Password, and
then click Login. By default:
User Name: admin
Password: admin
Note: User Name and Password are case
sensitive.
4
16. C lick Enabled for WDS Separation.
17. Enter the MAC address of the
TEW-715APO that you are connecting to.
18. Click Apply.
19. Click OK.
20. Please refer to the user manual for the
steps in setting up wireless encryption.
Note: To protect your network from any
unauthorized access it is recommended to
enable wireless encryption.
22. Click System and then click Network
Settings.
14. Click OK.
15. Click Wireless and then click WDS
Settings.
21. Click Back.
23. Select Use Fixed IP Address.
24. Configure the TEW-715APO's IP address to
a valid IP address within the subnet defined
by the Router. Avoid using an IP address
within the DHCP pool of your router. In this
example, we will assume the following:
Router IP Address: 192.168.10.1
Subnet Mask: 255.255.255.0
DHCP Pool:
192.168.10.100~192.168.10.199
The TEW-715APO will be setup with the
following IP address assignment:
IP Address: 192.168.10.200
Subnet Mask: 255.255.255.0
Gateway IP Address: 192.168.10.1
DNS 1: 192.168.10.1
5
25. Click Apply.
26. Click OK.
27. Repeat steps 2-26 for TEW-715APO #2.
Phase 2: Confirm Connectivity
Note:
1. Leave TEW-715APO #2 connected to your computer.
2. Connect TEW-715APO #1 to a LAN port of a router on your network.
3. To verify connectivity, run your computer's command prompt and ping TEW-715APO #1's
assigned IP address from your computer.
4. A successful ping reply determines that both TEW-715APOs are configured properly and
connected.
6
Building 1
Point-to-Point (WDS Bridge) Configuration
Building 2
3. Hardware Installation
Modem
Internet
Router
TEW-715APO #2
TEW-715APO #1
7
1. Refer to the above diagram.
2. Mount the TEW-715APOs in your desired location. See Pole Mounting the TEW-715APO for
mounting instructions.
3. Connect the TEW-715APOs to their respective network.
4. Confirm that the TEW-715APOs are facing each other.
5. Verify that the status LED indicators on both TEW-715APOs are fully functional: Power
(Solid/Green), LAN (Blinking/Green) and Signal Indicator [Wireless] (Green, Yellow or Red).
1. Loosen and remove the metal O-ring on the N-type connector.
2. Put the grounding wire into the connector and tighten up with the O-ring.
3. Connect the grounding wire to a grounding object. e.g. Earth driven rod or grounded electrical
system.
Connecting the Grounding Wire
Pole Mounting the TEW-715APO
8
2. Insert the pole mounting clamp through the
middle of the TEW-715APO.
Note:
The pole mounting clamp supports poles with
a maximum diameter of 63mm (2.48 inches).
1. Turn the screw on the pole mounting
clamp counter clockwise.
3. Wrap the mounting clamp around a pole.
4. Secure the TEW-715APO to pole by turning
the screw clockwise.
Wireless outdoor access point installation is
now complete.
For detailed information regarding the
TEW-715APO's configuration and advanced
settings and mounting instructions, please refer
to the User's Guide on the provided CD-ROM.
Autres manuels pour TEW-715APO
2
Table des matières
Autres manuels TRENDnet Routeur sans fil
TRENDnet
TRENDnet TEW-691GR Manuel utilisateur
TRENDnet
TRENDnet TEW-652BRP Manuel utilisateur
TRENDnet
TRENDnet TEW-635BRM - Wireless Router Manuel utilisateur
TRENDnet
TRENDnet TEW-431BRP Mode d’emploi
TRENDnet
TRENDnet TEW-691GR Manuel utilisateur
TRENDnet
TRENDnet TEW-712BR Manuel utilisateur
TRENDnet
TRENDnet TEW-651BR Manuel utilisateur
TRENDnet
TRENDnet TEW-800MB Manuel utilisateur
TRENDnet
TRENDnet TEW-731BR Manuel utilisateur
TRENDnet
TRENDnet TEW-818DRU Manuel utilisateur
TRENDnet
TRENDnet TEW-732BR Manuel utilisateur
TRENDnet
TRENDnet TEW-633GR - Wireless Router Manuel utilisateur
TRENDnet
TRENDnet TEW-611BRP Manuel utilisateur
TRENDnet
TRENDnet TEW-823DRU Manuel utilisateur
TRENDnet
TRENDnet TEW-711BR Manuel utilisateur
TRENDnet
TRENDnet TEW-733GR Manuel utilisateur
TRENDnet
TRENDnet TEW-659BRV Manuel utilisateur
TRENDnet
TRENDnet AC600 Manuel utilisateur
TRENDnet
TRENDnet TEW-431BRP Manuel utilisateur
TRENDnet
TRENDnet TEW-610APB Manuel utilisateur
